Kenwood TS-990S Instruction Manual page 241

Parameter Operation and activation of function assigned
Press to open the Noise Blanker 1 (Sub Band)
NB1 SEL (Sub
screen. The transceiver does not behave even if you
Band)
press and hold this PF key.
Press to open the Noise Blanker 2 (Sub Band)
NB2 SEL (Sub
screen. The transceiver does not behave even if you
Band)
press and hold this PF key.
Press and hold to open the Noise Reduction
NR1 SEL (Sub 1 (Sub Band) screen for the sub band. The
Band) transceiver does not behave even if you press and
hold this PF key.
Press and hold to open the Noise Reduction
NR2 SEL (Sub 2 (Sub Band) screen for the sub band. The
Band) transceiver does not behave even if you press and
hold this PF key.
Press to open the Audio Peak Filter screen for the
APF/SEL (Sub
sub band. The transceiver does not behave even if
Band)
you press and hold this PF key.
MUTE (Sub Band) Press to mute the audio of the sub band.
Press to enable the voice guidance of the main band
VOICE 1 (Main frequency.
Band) This is the default for Menu 17, "VOICE (Main Band):
Key Assignment".
Press to emit a voice guidance, such as a value for
the signal strength of the selected band during the
receive, and a value for transmit power during the
VOICE 2
transmit.
This is the default for Menu 15, "PF A Key: Key
Assignment".
Press to emit a voice guidance, such as a value of
the selected with [METER] (F). The transceiver does
VOICE 3 not emit the voice guidance during the reception.
This is the default for Menu 16, "PF B Key: Key
Assignment".
Press to enable the voice guidance of the sub band
VOICE 1 (Sub frequency.
Band) This is the default for Menu 18, "VOICE (Sub Band):
Key Assignment".
While you are holding down this key, the passband
DSP MONITOR
width of the IF filter is expanded to maximum.
While you are holding down this key, the squelch
RX MONITOR
opens.
TX TUNE Press to start the TX tuning.
Press to transmit the signal entered via the
DATA SEND modulation source (rear panel) configured for each
audio source.
Press to place the transceiver into a transmit state.
SEND Press again to revert the transceiver to the original
state.
Each time you press this key, the modulation line
cycles as follows: Off > ACC 2 > USB > OPT.
DATA VOX/SEL
Press and hold to open the Modulation Source
screen.
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 1.
CH1
This is the default for Menu 19, "External PF 1: Key
Assignment".
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 2.
CH2
This is the default for Menu 20, "External PF 2: Key
Assignment".
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 3.
CH3
This is the default for Menu 21, "External PF 3: Key
Assignment".
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 4.
CH4
This is the default for Menu 22, "External PF 4: Key
Assignment".
Contents Index
Parameter Operation and activation of function assigned
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 5.
CH5
This is the default for Menu 23, "External PF 5: Key
Assignment".
Press to transmit the Voice message, the CW
message, FSK message, or PSK message stored in
Message Memory
channel 6.
CH6
This is the default for Menu 24, "External PF 6: Key
Assignment".
Press to transmit the CW message, FSK message,
Message Memory or PSK message stored in channel 7.
CH7 This is the default for Menu 25, "External PF 7: Key
Assignment".
Press to transmit the CW message, FSK message,
Message Memory or PSK message stored in channel 8.
CH8 This is the default for Menu 26, "External PF 8: Key
Assignment".
Contest Number Press to subtract the contest number by one. (CW
Decrement Mode)
SWL Press to place the transceiver into SWL mode.
RF Scope Press to display the bandscope.
AF Scope Press to display the audio scope.
Waterfall Press to display the waterfall.
Extended Memory
Press to invoke the Extended Memory Channel.
Channel
Press to operate the transceiver in the same
manner as when the [DOWN] key of the optional
Down Key
microphone is pressed.
(Microphone)
This is the default for Menu 31, "Microphone DOWN:
Key Assignment".
Press to operate the transceiver in the same manner
as when the [UP] key of the optional microphone is
Up Key
pressed.
(Microphone)
This is the default for Menu 32, "Microphone UP:
Key Assignment".
Press to capture the screen images in the main
Capture screen and the sub-screen and save them as image
files to a USB flash drive.
Safe Removal of
Press to execute Safe Removal of the USB Flash
the USB Flash
Drive
Drive
Emergency Press to call using the frequency allocated to notify
Frequency the emergency call frequency on the main band.
Off Nothing is activated.
USEFUL FUNCTIONS 16
16-9