Sign In
Upload
Manuals
Brands
DURKOPP ADLER Manuals
Sewing Machine
745-35-10 D
DURKOPP ADLER 745-35-10 D Manuals
Manuals and User Guides for DURKOPP ADLER 745-35-10 D. We have
2
DURKOPP ADLER 745-35-10 D manuals available for free PDF download: Service Instructions Manual, Operating Instructions Manual
DURKOPP ADLER 745-35-10 D Service Instructions Manual (338 pages)
Brand:
DURKOPP ADLER
| Category:
Sewing Machine
| Size: 43.69 MB
Table of Contents
Table of Contents
3
1 About These Instructions
7
For Whom Are These Instructions Intended
7
Representation Conventions - Symbols and Characters
7
Other Documents
9
Liability
9
2 Safety
11
Basic Safety Instructions
11
Signal Words and Symbols Used in Warnings
12
3 Machine Head
15
Gages
15
Slot in the Arm Shaft Crank
15
Swiveling up the Machine Head
16
Swiveling down the Machine Head
18
Disassembling the Machine Head
19
Assembling Machine Head
21
Assembling the Crank Pin at the Arm Shaft
23
Needle Bar Linkage
28
Disassembling the Needle Bar Linkage
28
Removing a Needle Bar from the Needle Bar Linkage
31
Dismantling the Needle Bar
33
Assembling the Needle Bar
34
Assembling Needle Bars into the Needle Bar Linkage
35
Assembling the Needle Bar Linkage
38
Setting the Height of the Needle Bar Linkage
40
Aligning the Needle Bar Linkage with the Throat Plate
42
Changing the Needle Holder
43
Hook
45
Setting the Height of the Hook Shaft
45
Setting the Gear Clearance of the Hook Drive
47
Setting the Loop Stroke
48
Setting the Needle Holder Height
49
Setting the Distance between Hook Tips and Needles
51
Setting the Needle Guard
54
Changing the Hook
55
Setting the Bobbin Case Holding Wire
56
Middle Knife
58
Disassembling the Drive Motor
58
Assembling the Drive Motor
59
Disassembling the Switching Cylinder
60
Assembling the Switching Cylinder
61
Setting the Middle Knife
62
Setting the Thread Tension Spring
64
Setting the Trimming and Clamping Device for the Needle Threads
65
Setting the Trimming and Clamping Device for the Hook Threads
68
Setting the Thread Advancing Device for the Needle Threads
71
Setting the Synchronizer
72
Setting the Differential Gear
73
4 Transport Carriage
75
Setting the Rear End Position of the Transport Carriage
75
Setting the Position of the Reference Switch in the Slotted Hole
76
Setting the Distance between Switching Screw and Reference Switch
77
Setting the Transport Carriage Stop
78
Changing the Toothed Belt
79
Setting the Toothed Belt Tension
82
5 Transport Clamps
85
Aligning the Transport Clamps with the Sliding Plate Edge
86
Setting the Stroke Height of the Transport Clamps
87
Setting the Distance of the Transport Clamps to the Folder Sole
89
Setting the Front End Position of the Transport Clamp
91
6 Corner Knife
93
Setting the Initial Position of the Corner Knives
93
Setting the Corner Knife Parameters
94
Checking the Corner Knife Station
96
Checking the Front Left Corner Knife
97
Checking the Rear Left Corner Knife
98
Aligning the Corner Knife Station with the Seams
98
Setting the Slant of the Corner Knife Cuts
101
Replacing Corner Knives
102
7 Aligning the Marking Lamps
103
8 Light Barriers
107
Setting the Swivel Arm
107
Aligning the Light Barrier
108
Setting the Light Barrier for the Flap
114
Aligning the Air Nozzles for Cleaning the Reflecting Foils
115
9 Setting the Folding Station Plate
117
10 Aligning the Machine Head
119
11 Setting Fabric Sliding Plate and Vacuum Plate
123
12 Folder
125
Assembling the Folder
125
Aligning the Folder with the Middle of the Pocket Opening
126
13 Positioning Device
129
Aligning the Positioning Device
129
Setting the Pattern Shift Correction
130
Setting the Throttle Valve
131
Setting the Pocket Bag Feed
132
Setting the Loading Position
132
Setting the Position of the Assembly Strip
133
Setting the Throttle Valve
134
14 Additional Equipment
135
Setting the Outfeed Roller
135
Setting the Tape Feeding and Tape Cutting Device
137
15 Throw-Over Stacker
139
Checking the Function Sequence
139
Setting the Throw-Over Stacker
142
Setting the Stacking Speed
145
Activating the Stacker
145
16 Pressure Supply
147
Setting the Pressure Monitor
147
Setting the Transport Clamp Control
148
17 Programming
149
18 Maintenance
283
Cleaning
284
Lubricating
285
Checking the Oil Level in the Oil Reservoir
286
Lubricating the Hook
287
Servicing the Pneumatic System
288
Setting the Operating Pressure
288
Draining the Water Condensation
289
Cleaning the Filter Element
290
Parts List
291
19 Decommissioning
293
20 Disposal
295
21 Troubleshooting
297
Customer Service
297
Messages of the Software
297
22 Technical Data
309
23 Appendix
311
Advertisement
DURKOPP ADLER 745-35-10 D Operating Instructions Manual (256 pages)
Brand:
DURKOPP ADLER
| Category:
Sewing Machine
| Size: 29.62 MB
Table of Contents
Table of Contents
3
1 About These Instructions
5
For Whom Are These Instructions Intended
5
Representation Conventions - Symbols and Characters
5
Other Documents
7
Liability
7
2 Safety
9
Basic Safety Instructions
9
Signal Words and Symbols Used in Warnings
10
3 Machine Description
13
Components of the Machine
13
Proper Use
14
Declaration of Conformity
15
4 Operation
17
Preparing the Machine for Operation
17
Switching on the Machine
17
Swiveling the Folding Station to the Side
18
Locking the Folding Station in Place
19
Inserting/Changing the Needles
20
Threading the Needle Thread
21
Winding the Hook Thread
24
Changing the Bobbins
25
Thread Tension
26
Setting the Needle Thread Tension
27
Setting the Hook Thread Tension
28
Sliding Back the Hood and Removing the Fabric Sliding Plate
29
Swiveling up the Machine Head
31
Swiveling down the Machine Head
33
Remaining Thread Monitor
34
Stacker Control
35
Corner Knife Station
36
Swivel the Corner Knife Station in and out
36
Adjust Corner Knife
37
Setting the Reference Position
38
Performing a Quick Stop
38
Flap and Piping Projection
39
Additional Equipment
40
Roll-Off Device
40
Tape Feeder and Automatic Cutter
41
Vacuum Device
44
Sewing
45
Start Sewing
45
Sewing Breast Welt Pockets
46
5 Programming
51
6 Maintenance
185
Cleaning
186
Lubricating
187
Lubricating the Machine Head
188
Lubricating the Hook
189
Servicing the Pneumatic System
190
Setting the Operating Pressure
190
Draining the Water Condensation
191
Cleaning the Filter Element
192
Parts List
193
7 Setup
195
Checking the Scope of Delivery
195
Removing the Transport Locks
195
Setting up the Machine
196
Lifting the Machine
196
Rolling the Machine (Optional)
196
Assembling and Connecting the Pedal
197
Setting the Working Height
199
Assembling the Machine Parts Removed for Shipping
200
Assembling the Reel Stand
200
Assembling the Control Panel
201
Assembling Winder and Tray
201
Assembling the Cylinder for the Pick-Up Folder Stroke
202
Assembling the Workpiece Boxes (Optional)
203
Mounting the Table Extensions (Additional Equipment)
204
Electrical Connection
206
Pneumatic Connection
207
Assembling the Compressed Air Maintenance Unit
207
Setting the Operating Pressure
207
Connection to the In-House Vacuum System
208
Performing a Test Run
209
8 Decommissioning
211
9 Disposal
213
10 Troubleshooting
215
Customer Service
215
Messages of the Software
215
11 Technical Data
227
12 Appendix
229
Advertisement
Related Products
DURKOPP ADLER 745-34 -
Durkopp Adler 745-34-2
DURKOPP ADLER 745 - 34 - 2
DURKOPP ADLER 745-35-10 S
DURKOPP ADLER 745-35-10 A
DURKOPP ADLER 745-35-10 B
DURKOPP ADLER 745-35-10 F
DURKOPP ADLER 743-422
DURKOPP ADLER 7700
DURKOPP ADLER 756
DURKOPP ADLER Categories
Sewing Machine
Sewing Machine Accessories
Accessories
Controller
Scanner
More DURKOPP ADLER Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL