Sharp MX-M264U Service Manual page 98

26-3
Purpose Setting
Function (Purpose) Used to set the specifications of the auditor.
(Setting must be made according to the
auditor use conditions.)
Section Auditor
Operation/Procedure
Select an item to be set with the touch panel.
Item/Display
BUILT-IN P10
AUDITOR
OUTSIDE NONE
AUDITOR
P VENDOR1
P VENDOR3
P OTHER
VENDOR-EX
(*1)
VENDOR-EX
(MULTI) (*1)
S_VENDOR
DOC ADJ ON
OFF
PF ADJ ON
OFF
VENDOR MODE1
MODE (*2)
MODE2
MODE3
Default
Content
value
Built-in auditor mode P10
(standard mode) operation.
No external connection NONE
vendor is used.
Coin vendor mode
(Only the copy mode can
be controlled.)
Vendor mode in which
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
Mode for an external
auditor connected to the
SCU.
Vendor I/F for EQUITRAC
VENDOR-EX + Multi job
cueing Enable mode
Serial vendor mode
Support for the auditor in OFF
document filing print
No support for the auditor in
document filing print
Continuous printing is OFF
performed in the duplex
print mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
Continuous printing is not
performed in the duplex
print mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back
surface.
Vendor mode 1 MODE
3
Vendor mode 2
Vendor mode 3
MX-M264U SIMULATION 6 – 24
Item/Display
COUNTUP FUSER_IN
TIMING
FUSER_OUT
EXIT_OUT
(*1) Displayed only when EQUITRAC.
(*2) Details of the vendor mode
Details of the vendor mode
Completion Insufficient money during
of the
specified
quantity.
(no money
(Money
remaining)
remaining)
Condition 1 Condition 2
MODE1 Operation 1 Operation 2
MODE2 Operation 1 Operation 1
MODE3 Operation 1 Operation 3
Operation 1:
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
26-5
Purpose Setting
Function (Purpose) Used to set the count mode of the total
counter and the maintenance counter. (A3/
11x17 size)
Section
Operation/Procedure
1) Select an item to be set with scroll keys.
2) Enter the setting value with 10-key
1 = Count up by 1, 2 = Count up by 2
3) Press [OK] key.
The set value in step 2) is saved.
Item/Display
A TOTAL (B/W) Total counter (B/W)
B MAINTE (B/W) Maintenance counter (B/W)
C DEV (B/W) Developer counter (B/W)
Default
Content
value
Mode in which the detection EXIT_
timing of the paper lead OUT
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
Mode in which the detection
timing of the paper rear
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
Mode in which the detection
timing of the paper rear
edge by the paper exit
sensor of the right paper
exit tray or of the after
process unit is used as the
money charging timing.
Completion
copy job of the
specified
BW BW
quantity.
(money
(No money
remaining)
remaining)
Condition 3 Condition 4
Operation 2 Operation 1
Operation 2 Operation 1
Operation 2 Operation 3
Content Default value
1
(Japan)
2
(Except Japan)
2