Sharp MX-M264U Service Manual page 97

25-2
Purpose Setting
Function (Purpose) Used to make the initial setting of toner
density when replacing developer. (Auto-
matic adjustment)
Section Image process (Photoconductor/Develop-
ing)
Operation/Procedure
1) Press [EXECUTE] key.
The developing motor rotates and the toner density sensor makes
sampling of the toner density, displaying the detected level.
After stopping the developing motor, it is set as the reference toner
density control level.
CAUTION: When the above operation is interrupted on the way, the
reference toner concentration level is not set. Also when
error code of EE-EL or EE-EU is displayed, the refer-
ence toner density level is not set normally.
CAUTION: Do not execute this simulation except when new devel-
oper is supplied. If it is executed in other cases, under-
toner or overtone may occur, causing a trouble.
Item/Display Content
AT DEVE ADJ Automatic development
adjustment value
Display during execution of the simulation
Item/Display
TCS Toner sensor output value
Error content
Display Error name
EE-EL EL abnormality The sensor output level is less than 78.
EE-EU EU abnormality The sensor output level exceeds 178.
25-4
Purpose Adjustment/Setting/Operation data check
Function (Purpose) Used to display the operation data of the
toner correction quantity. (Not used in the
market.)
Section Process
Operation/Procedure
The operation data of the toner supply quantity are displayed.
Item/Display
TONER DEN_LT Current toner density sensor output
value (final value)
TONER DEN_ST Current toner density reference
value display (the value including all
the correction values)
AUTO DEVE Automatic development adjustment
value
ALL All correction reference value
LIFE Life correction value
ENV Environment correction value
DUPLEX Duplex correction value
PRINT RATE Print ratio correction value
AREA Area correction value
AUTO DEVE AREA Area in the auto development
adjustment
CURRENT AREA Current area
Display Default
range value
1 - 255 128
Content
Error content
Display
Content
range
1 - 255
1 - 255
1 - 255
1 - 255
-128 - 127
-128 - 127
-128 - 127
-128 - 127
-128 - 127
-128 - 127
-128 - 127
MX-M264U SIMULATION 6 – 23
26
26-1
Purpose Setting
Function (Purpose) Used to set Yes/No of installation of the Job
separator.
Section Paper exit
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key. (The set value is saved.)
This setting is required to use the Job separator.
Item/Display
A 0 YES
1 NO
26-2
Purpose Setting
Function (Purpose) Used to set the paper size of the paper feed
tray. (When the paper size is changed, this
simulation must be executed to change the
paper size in software.)
Section Paper feed
Operation/Procedure
Select a paper size and a weight system to be changed.
Item Setting value
LEGAL SET
G/LBS SET
Destination
LEGAL SET
U.S.A 8.5 x 14
CANADA 8.5 x 14
INCH 8.5 x 14
JAPAN 8.5 x 14
AB_B 8.5 x 14
EUROPE 8.5 x 14
U.K. 8.5 x 14
AUS. 8.5 x 14
AB_A 8.5 x 14
CHINA 8.5 x 14
Content
Job separator provided
Job separator not provided
Content
0 8.5 x 14
1 8.5 x 13.4
2 8.5 x 13.5
0 GRAM
1 LBS
Setting value
G/LBS SET
LBS
LBS
LBS
GRAM
GRAM
GRAM
GRAM
GRAM
GRAM
GRAM