Sharp MX-M264U Service Manual page 102

Item/Display
B REMAINING 0.45 8 Toner
TONER preparation at
LEVEL remaining toner
level of 45%
0.5 9 Toner
preparation at
remaining toner
level of 50%
C TONER NEAR END 0 The toner near
(0:YES 1:NO) end message is
displayed.
1 The toner near
end message is
not displayed.
D TONER END 1 Operation setup
1
2 Operation setup
2
3 Operation setup
3
E TONER END Setting of the
COUNT number of copy/print/
FAX outputs Enable
after TONER NEAR
END.
F TONER E-MAIL 0 Low status send
ALERT of E-mail alert
(When the toner
preparation
message is
displayed) (in
near near toner
end)
1 Low status send
of E-mail alert
(near toner end)
Item E (TONER END COUNT) setting value and printable quan-
tity
Setting value Printable quantity at A4/6% equivalent conversion
1
2
3
4
5
List of Default values and set values for each destination
Destination
Toner preparation
message
U.S.A 0 (Displayed)
CANADA 0 (Displayed)
INCH 0 (Displayed)
JAPAN 0 (Displayed)
AB_B 0 (Displayed)
EUROPE 0 (Displayed)
U.K. 0 (Displayed)
AUS. 0 (Displayed)
AB_A 0 (Displayed)
CHINA 0 (Displayed)
Setting Default
Content
range value
0 - 9 4
0 - 1 List of
Default
values and
set values
for each
destination
1 - 3 –
1 - 5 4
0 - 1 1
0
20
40
80
160
Setting value
Toner near end message
0 (Displayed)
0 (Displayed)
0 (Displayed)
1 (Not Displayed)
0 (Displayed)
0 (Displayed)
0 (Displayed)
0 (Displayed)
0 (Displayed)
0 (Displayed)
MX-M264U SIMULATION 6 – 28
Contents of set items
A: Enable/Disable setting of the toner preparation message display.
B: The toner remaining quantity at which the toner preparation
message is displayed.
C: Enable/Disable setting of the toner preparation message display
when the toner near end status is reached.
D: Machine operation at toner end
E: Number of allowable copy/print/FAX when the toner near end
message is displayed. (Range: 0 - 160 sheets)
The number of output print allowed in item D is based on the
assumption that the sheets are of A4 size with print ratio of 6%.
(The number of outputs allowed differs depending on the paper
size and the print ratio.)
CAUTION: When item A is set to "0" and item E is properly set,
printing can be made after toner near end. However,
improper phenomena such as insufficient density, thin
spots, or improper color balance may result depending
on the using conditions. When item E is set to "1" print-
ing is disabled after toner near end. In this case, toner
end display is made in the toner near end status, and
copy/print/FAX outputs are disabled.
26-73
Purpose Setting
Function (Purpose) Enlargement continuous shoot, A3 wide
copy mode image loss (shade delete quan-
tity) adjustment
Section
Operation/Procedure
1) Select an item to be set with scroll keys.
2) Enter the set value with 10-key.
3) Press [OK] key.
When the adjustment value is increased, the image loss
(shade delete quantity) is increased.
Item/Display Content
A DELETING Rear frame side
SHADOW ADJ image loss quantity
(M) (shade delete
quantity) adjustment
B DELETING Lead edge image
SHADOW ADJ (S) loss quantity (shade
delete quantity)
adjustment
26-74
Purpose Setting
Function (Purpose) Used to set the OSA trial mode.
Section
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key.
Item/Display
A OSA TRIAL MODE 0
(0: YES 1: NO)
1
Setting
Default value
range
0 - 50 0
(Adjustment
amount:
0.1mm/step)
0 - 50 0
(Adjustment
amount:
0.1mm/step)
Setting Default
Content
range value
Used to set the 0 - 1
OSA trial mode.
OSA trial mode is
canceled.
1