Sharp MX-M264U Service Manual page 100

26-38
Purpose Setting
Function (Purpose) Used to set Continue/Stop of print when the
maintenance life is reached.
Section
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key.
The set value in step 1) is saved.
Item/Display
A MAINTENANCE 0
LIFE OVER
(0: CONTINUE
1: STOP)
1
26-50
Purpose Setting
Function (Purpose) Used to set functions.
Section
Operation/Procedure
1) Select a target item of setting with scroll key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
Item/Display
A BW REVERSE 0
1
B FINISHER 0
FUNCTION
1
C FEED TRAY 0
COLOR
1
D LONG SIZE PRINT 0
1
E WIRELESS SET 0
1
(*1) Default values for each destination of item A
Destination
U S A
CANADA
INCH
JAPAN
AB_B
EUROPE
U K
AUS
AB_A
CHINA
Default
Content
value
Setting of Print Continue/
Stop when the maintenance
life is over (Print Continue)
Setting of Print Continue/
Stop when the maintenance
life is over (Print Stop)
Default
Content
value
BW reverse copy Disable Refer
to *1
BW reverse copy Enable
Finisher special paper
The number of paper exit is Refer
limited. to *2
Finisher special paper
The number of paper exit is
not limited.
Paper feed tray color display
ON during paper feed
Paper feed tray color display
OFF during paper feed
Long size print disable
Long size print enable
Wireless LAN disable
Wireless LAN enable
Item A
1
1
1
1
1
1
0
1
1
1
MX-M264U SIMULATION 6 – 26
(*2)
Target
paper
Inner Postcard,
finisher envelope
Label
sheet,
0
tab sheet,
OHP
26-51
Purpose
Function (Purpose) Used to set the specifications of the serial
Section
Operation/Procedure
1) Enter the set value with 10-key.
When the PCI is installed, setting is made to 1 or 2.
2) Press [OK] key.
Item/Display
0
A PCI
SETTING
0
MODE1: Red LED is light/blink/OFF, MODE2: Red LED always
OFF
0
CAUTION: When "PCI SETTING" is changed from "0" to "1" or "2,"
if SIM26-03
0
"S_VENDOR," "OUTSIDE AUDITOR" is changed to
"NONE."
26-52
Purpose
Function (Purpose) Used to set whether non-printed paper
Section
Operation/Procedure
1) Enter the set value with 10-key.
0
1
Target paper setting
0
The operation is stopped when
10 sheets of a same kind are
discharged continuously. When,
however, different kinds of
sheets are mixed and
discharged and 10 or less
sheets of a kind are
continuously discharged, the
operation is stopped by the
paper exit tray full detection.
The operation is stopped when
100 sheets of a same kind are
discharged continuously. When,
however, different kinds of
sheets are mixed and
discharged and 100 or less
sheets of a kind are
continuously discharged, the
operation is stopped by the
paper exit tray full detection.
Setting
port operation. (For PCI)
Content
Serial port PCI mode OFF
(For connecting the serial
port vendor)
Serial port PCI mode ON
(JOB status LED: MODE1)
Serial port PCI mode ON
(JOB status LED: MODE2)
"OUTSIDE AUDITOR"
Setting
(insertion paper, cover paper) is counted up
or not.
Count up
No count up
1
If it is set to "1,"
the operation is
stopped when
the paper exit
tray is full or
when 250
sheets
(35.5mm thick)
are discharged.
Setting Default
range value
0 0
(Serial
port PCI
mode
OFF)
is set to