Sharp MX-M264U Service Manual page 135

Mode Display/Item
ENGINE F MANUAL PLAIN PAPER (L)
G MANUAL HEAVY PAPER (S)
H MANUAL HEAVY PAPER (L)
I MANUAL OHP
J MANUAL ENV
K ADU PLAIN PAPER (S)
L ADU PLAIN PAPER (L)
M DESK (S)
N DESK (L)
Note on "Large size" and "Small size"
Small size: The paper length in the transport direction is shorter than the LT size (216mm).
Large size: The paper length in the transport direction is longer than the LT size (216mm).
Adjustment value
When the adjustment value is increased, the warp amount is increased. When the adjustment value is decreased, the warp amount is
decreased.
(When the adjustment value is changed by 1, the stop timing is changed by 0.1mm.)
51-9
Purpose Adjustment/Setup
Function (Purpose) Used to adjust the ON/OFF timing of the
separation voltage.
Section
Operation/Procedure
1) Select an adjustment target item with scroll key.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
Item Display Content
A SHV ON Separation voltage ON/OFF
timing adjustment *
B SHV OFF Separation voltage OFF timing
adjustment *
*1: Transfer V2ON reference
(Synchronized with the adjustment value of 50)
*2: Transfer V2OFF reference
(Synchronized with the adjustment value of 50)
53
53-6
Purpose Adjustment
Function (Purpose) Used to adjust the detection level of the
RSPF document width.
Section
Operation/Procedure
1) Open the RSPF paper feed guide to the maximum width.
2) Press [EXECUTE] key.
The maximum width detection level is recognized.
3) Open the RSPF paper feed guide to the A4R width.
4) Press [EXECUTE] key.
The A4R width detection level is recognized.
5) Open the RSPF paper feed guide to the A5R width.
Manual feed tray/deflection adjustment value (Plain paper/Large size)
Manual feed tray/deflection adjustment value
(Heavy paper/Small size)
Manual feed tray/deflection adjustment value
(Heavy paper/Large size)
Manual feed tray/deflection adjustment value (OHP)
Manual feed tray/deflection adjustment value (Envelope)
ADU/deflection adjustment value
(Plain paper/Small size)
ADU/deflection adjustment value
(Plain paper/Large size)
DESK/deflection adjustment value
(Plain paper/Small size)
DESK/deflection adjustment value
(Plain paper/Large size)
Setting Default
range value
25 - 90
1
50 - 90
2
MX-M264U SIMULATION 6 – 61
Content
6) Press [EXECUTE] key.
The A5R width detection level is recognized.
7) Open the RSPF paper feed guide to the minimum width.
8) Press [EXECUTE] key.
The minimum width detection level is recognized.
When the above operation is nor performed normally, "ERROR" is
displayed and. When the above operation is completed normally,
"COMPLETE" is displayed.
1 TRAYVOLMAX
2 TRAYVOLA4R
3 TRAYVOLA5R
4 TRAYVOLMIN
50
75
53-7
Purpose
Function (Purpose) Used to adjust the RSPF document size
Section
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
A AD_MAX
B AD_P1
C AD_P2
D AD_MIN
LT size (216mm)
or above
LT size (216mm)
or less
LT size (216mm)
or above
-
-
LT size (216mm)
or less
LT size (216mm)
or above
LT size (216mm)
or less
LT size (216mm)
or above
Tray size volume maximum value
Tray volume A4R size adjustment value
Tray volume A5R size adjustment value
Tray size volume minimum value
Adjustment/Setup
width sensor.
Item/Display
Max. width position
A4R width position
A5R width position
Min. width position
Setting Default
range value
1 - 99 40
1 - 99 70
1 - 99 70
1 - 99 30
1 - 99 40
1 - 99 50
1 - 99 50
1 - 99 20
1 - 99 25
Setting Default
range value
0 - 1023 84
0 - 1023 509
0 - 1023 808
0 - 1023 961