Sony XDS-1000 Operation Manual page 46

Item Setting
F4: A8 INPUT Selects the audio input signal to assign
to audio channel 8.
SDI: Audio signal embedded into SDI
ANALOG2: Input signal to the ANALOG
AES/EBU8: Signal input to the DIGITAL
DVB-ASI: DVB-ASI TS signal
F5: – (Unassigned function button)
F6: – (Unassigned function button)
a) When the maintenance menu item M22: OPTION SETTING >DVB-ASI
is set to "on" with the optional PDBK-202 being installed (see page 113).
P3 AUDIO page
Item Setting
F1: A5 VOL Sets the volume of audio channel 5.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to +12
dB) by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F2: A6 VOL Sets the volume of audio channel 6.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to +12
dB) by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F3: A7 VOL Sets the volume of audio channel 7.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to +12
dB) by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F4: A8 VOL Sets the volume of audio channel 8.
The volume can be adjusted within the
range from –200 to 0 to +200 (–∞ to +12
dB) by turning the PUSH SET knob. The
volume changes in steps of ±10 if you
hold the SHIFT button down while you
turn the knob.
F5: – (Unassigned function button)
F6: – (Unassigned function button)
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to "REC" or "PB".
• Set setup menu item 131 AUDIO VOLUME to "each".
46
Basic Operations of the Function Menu
signal
AUDIO INPUT 2 connector
AUDIO (AES/EBU) IN 7/8
connectors
a)
P4 TC page
Item
F1: TCG
a)
F2: PRST/RGN
a)
a)
F3: RUN MODE
a)
F4: DF/NDF
F5: PDPSET
Setting
Selects the timecode signal to which the
internal timecode generator
synchronizes.
INT: Follow the initial value set from the
front panel or remotely from the
device connected to a REMOTE
(9P) connector.
EXT: Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SYS: Synchronize to standard reference
timecode signal broadcast station
input to the SYSTEM TC INPUT
connector.
SDI: Synchronize to timecode
embedded into HD-SDI or SD-SDI
signal input to the HD/SD-SDI
INPUT connector.
Note
If you select "EXT" or "SDI" when a DVB-
ASI TS signal is input, the internal
timecode generator synchronizes to
timecode data contained in the TS
signal.
Selects the following for the internal
timecode generator.
PRESET: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified
from the front panel or remotely from
the device connected to a REMOTE
(9P) connector.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC: Generate timecode synchronized
to VITC read by the internal
timecode reader.
Selects the timecode run mode.
FREE RUN: Timecode advances as long
as the unit is powered on, regardless
of the unit's operating state.
REC RUN: Timecode advances only
during recording. When you select
this item, also set F1: TCG on this
page to "INT" and set F2: PRST/
RGN to "PRESET".
Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF: Drop-frame mode
NDF: Non-drop-frame mode
When the system frequency is set to
1080/59.94i, 1080/29.97P, or 720/
59.94P, presets the timecode of the A
frame of the pulldown sequence.
24F TC: Reference timecode for A frame
30F TC: Timecode after pulldown
conversion from 24-frame timecode