Table of Contents
Advertisement
Sequencer mode
Once the Program has been loaded, you can change
any or all of the Tone Adjust settings as desired,
including both assignments and values. All such edits
are stored in the Song, without affecting the original
Program.
If Auto Load PRG is On, Tone Adjust settings will be
automatically loaded along with the Program.
If Auto Load PRG is Off, then the relationship
between the types of the old and new Programs will
determine what happens, as shown in the table below:
If the old
Program is...
An HD-1 Program
An HD-1 Program
Any EXi Program
An EXi Program
An EXi Program
Selected parameter information
This status line shows detailed, read-only information
about the currently selected Tone Adjust parameter.
(Control)
This is the physical controller assigned to the Tone
Adjust parameter. Slider M is the Master Slider.
(Assignment)
This shows the full name of the parameter assigned to
the controller. You can change this using the "Assign"
parameter, below.
Value
This shows the current value of the parameter. The
range of values will vary depending on the parameter
assigned to the control.
Type
This shows the type of the parameter, which relates to
how edits to the parameter are saved. For more
information, see "Absolute, Relative, and Meta
parameters" on page 26.
448
Then Tone
Adjust
And the new
parameters
Program is...
and values
are...
An HD-1 Program
kept the same
loaded from
the new
An EXi Program
Program
loaded from
An HD-1 Program
the new
Program
An EXi Program
with the same EXi
assigned to the
kept the same
same slots as the
previous Program
An EXi Program
which does not
loaded from
use the same EXi
the new
as the previous
Program
Program
[Knob1...8, SW1...16,
Slider1...8, Slider M]
[Full Parameter Name]
[Current Parameter Value]
[Relative, Absolute, Meta]
Stored Value
[Original Parameter Value]
This shows the original value of the parameter, before
the effects of Tone Adjust. It applies only to Tone
Adjust parameters which control a single Program
parameter.
If you un-assign a parameter from a control, it will
revert to this value.
Knobs 1–8
Assign
[List of Tone Adjust assignments]
This lets you assign a Tone Adjust parameter to the
knob.
The first group of parameters are the Common set,
which are supported by most Program types. For a full
list, see "Common Tone Adjust Parameters" on
page 344.
After the Common parameters, the items in the list will
vary depending on the Program type. For more
information, please see:
"HD-1 Tone Adjust Parameters," on page 29.
"AL-1 Tone Adjust parameters," on page 210.
"CX-3 Tone Adjust parameters," on page 232.
"STR-1 Tone Adjust parameters" on page 278.
"MS-20EX Tone Adjust parameters" on page 305
"PolysixEX Tone Adjust parameters" on page 319.
Other EXi instruments will have their own set of
parameters, as described in their manuals.
Assignments are exclusive
Each controller can be assigned to only one parameter,
and each parameter can be assigned to only one
controller.
To swap a parameter from one control to another,
you'll need to first un-assign it from the old control,
and then assign it to the new control.
Value
This shows the current value of the parameter. The
range of values will vary depending on the parameter
assigned to the control.
Switches 1–16
Tone Adjust switches act a little differently than knobs
and sliders.
When a switch is assigned to a Relative parameter, or
an Absolute parameter with more than two states:
Switch On = On Value (see below)
Switch Off = the Program's stored value
When a switch is assigned to a two-state Absolute
parameter, such as Hold, the switch status directly
reflects the parameter value:
Switch On = On
Switch Off = Off
Assign
[List of Tone Adjust assignments]
This lets you assign a Tone Adjust parameter to the
switch. For more information, see "Assign," above.
[Depends on parameter]
Advertisement
Table of Contents
