069: Stereo Pitch Shifter - Korg Electronic Keyboard Parameter Manual

High Damp [%]
Sets the damping amount in the high range.
OUTPUT
This is the standard effects output section, with
modulatable control over wet/dry balance. For more
information, see "OUTPUT" on page 764.
PITCH SHIFTER: Mode
This parameter switches the pitch shifter operating
mode. With Slow, tonal quality will not be changed too
much. With Fast, the effect becomes a Pitch Shifter that
has a quick response, but may change the tone.
Medium is in-between these two. If you do not need to
set too much pitch shift amount, set this parameter to
Slow. If you wish to change the pitch significantly, use
Fast.

069: Stereo Pitch Shifter

Stereo In - Stereo Out
Left
Pitch Shifter
Input Level
Pre
Feedback Position
Pre
Input Level
Pitch Shifter
Right
This is a stereo pitch shifter. The pitch shift amount for
the left and right channels can be reversed from each
other.
INPUT
Input Level Dmod [%]
Sets the modulation amount of the input level. p.820.
Source
Selects the modulation source for the input level. p.820.
PITCH SHIFTER
Mode
Switches Pitch Shifter mode. p.821.
L/R Pitch
Determines whether or not the L/R pitch shift amount
is inverted.
Normal: The pitches of the left and right channels shift
together.
Up/Down: the pitch shift amount for the right channel
will be reversed. If the pitch shift amount is positive,
the pitch of the left channel is raised, and the pitch of
the right channel is lowered.
Pitch Shift [1/2 steps]
Sets the pitch shift amount in steps of a semitone.
p.821.
[0...100]
Wet / Dry
High Damp
Delay
Post
Feedback Spread
Post
Delay
High Damp
Wet / Dry
[+/–100]
[Off...Tempo]
[Slow, Medium, Fast]
[Normal, Up/Down]
[–24...+24]
Modulation and Pitch Shift
PITCH SHIFTER: Fine Amount, Fine [cents], Pitch Shift
Amount, Source, Pitch Shift [semitone]
The amount of pitch shift will use the value of the
Pitch Shift plus the Fine value. The amount of
modulation will use the Amount value plus Fine
Amount.
The same Modulation Source is used for both Pitch
Shift and Fine.
DELAY: Feedback and Feedback Position
When Feedback Position is set to Pre, the pitch shifter
output is again input to the pitch shifter. Therefore, if
you specify a higher value for the Feedback parameter,
the pitch will be raised (or lowered) more and more
each time feedback is repeated.
If Feedback Position is set to Post, the feedback signal
will not pass through the pitch shifter again. Even if
you specify a higher value for the Feedback parameter,
the pitch-shifted sound will be repeated at the same
pitch.
Fine [cents]
Sets the pitch shift amount in steps of one cent. p.821
Source
Selects the modulation source of pitch shift amount.
p.821.
Pitch Shift Amount
Sets the modulation amount of pitch shift amount.
p.821.
Fine Amount
Sets the modulation amount of pitch shift amount.
p.821.
DELAY
L Delay Time [msec]
Sets the delay time for the left channel.
R Delay Time [msec]
Sets the delay time for the right channel.
Feedback Position
Switches the feedback connection. p.821.
Feedback
Sets the feedback amount. p.821.
High Damp [%]
Sets the damping amount in the high range.
Spread
Sets the width of the stereo image of the effect sound.
p.829.
069: Stereo Pitch Shifter
[+/–100]
[Off...Tempo]
[–24...+24]
[+/–100]
[0...2000]
[0...2000]
[Pre, Post]
[+/–100]
[0...100]
[+/–100]
821