Using Device Clear; Scpi Conformance Information; Scpi Conformed Commands; Non-Scpi Commands - Agilent Technologies 66111A User Manual

6 - Introduction to Programming

Using Device Clear

You can send a device clear at any time abort a SCPI command that may be hanging up the GPIB
interface. The status registers, the error queue, and all configuration states are left unchanged when a
device clear message is received. Device clear performs the following actions:
♦ The input and output buffers of the dc source are cleared.
♦ The dc source is prepared to accept a new command string.
The following statement shows how to send a device clear over the GPIB interface using Agilent BASIC:
CLEAR 705
The following statement shows how to send a device clear over the GPIB interface using the GPIB
command library for C or QuickBASIC:
IOCLEAR (705)

SCPI Conformance Information

SCPI Conformed Commands

The Agilent 66111A, 66311B/D, and 66309B/D conform to SCPI Version 1995.0.
ABOR
CAL:DATA
CAL:STAT
DISP[:WIND][:STAT]
DISP[:WIND]:TEXT[:DATA]
INIT[:IMM]:SEQ | NAME
INIT:CONT:SEQ | NAME
MEAS | FETC:ARR:CURR[:DC]?
MEAS | FETC:ARR:VOLT[:DC]?
MEAS | FETC[:SCAL]:CURR[:DC]?
MEAS | FETC[:SCAL]:CURR:HIGH?
MEAS | FETC[:SCAL]:CURR:LOW?
MEAS | FETC[:SCAL]:CURR:MAX?
MEAS | FETC[:SCAL]:CURR:MIN?
MEAS | FETC[:SCAL]:VOLT[:DC]?
MEAS | FETC[:SCAL]:VOLT:HIGH?
MEAS | FETC[:SCAL]:VOLT:LOW?
MEAS | FETC[:SCAL]:VOLT:MAX?
MEAS | FETC[:SCAL]:VOLT:MIN?
OUTP[:STAT]
OUTP:PROT:CLE

Non-SCPI Commands

CAL:CURR[:SOUR][:DC][:POS]
CAL:CURR[:SOUR][:DC]:NEG
CAL:MEAS[:DC]:LOWR
CAL:MEAS:AC
CAL:LEV
CAL:PASS
CAL:SAVE
CAL:VOLT[:DC]
CAL:VOLT:PROT
DISP[:WIND]:MODE
MEAS | FETC[:SCAL]:CURR:ACDC?
MEAS | FETC[:SCAL]:VOLT:ACDC?
74
IEEE-488 Device Clear
OUTP:PROT:DEL
OUT:PROT:STAT
[SOUR]:CURR[:LEV][:IMM][:AMPL]
[SOUR]:CURR[:LEV]:TRIG[:AMPL]
[SOUR]:CURR:PROT:STAT
[SOUR]:VOLT[:LEV][:IMM][:AMPL]
[SOUR]:VOLT[:LEV]:TRIG[:AMPL]
[SOUR]:VOLT:PROT
SENS:CURR[:DC]:RANG[:UPP]
SENS:FUNC
SENS:SWE:OFFS:POIN
SENS:SWE:POIN
SENS:SWE:TINT
STAT:OPER[:EVEN]?
STAT:OPER:COND?
STAT:OPER:ENAB
STAT:OPER:NTR
STAT:OPER:PTR
STAT:PRES
STAT:QUES[:EVEN]?
STAT:QUES:COND?
OUTP:DFI[:STAT]
OUTP:DFI:SOUR
OUTP:PON:STAT
OUTP:RI:MODE
OUTP:TYPE
SENS:CURR:DET
[SOUR]:DIG:DATA[:VAL]
[SOUR]:DIG:FUNC
TRIG:SEQ2 | ACQ:COUN:CURR | :VOLT
TRIG:SEQ2 | ACQ:HYST:CURR | :VOLT
TRIG:SEQ2 | ACQ:LEV:CURR | :VOLT
TRIG:SEQ2 | ACQ:SLOP:CURR | :VOLT
STAT:QUES:ENAB
STAT:QUES:NTR
STAT:QUES:PTR
SYST:ERR?
SYST:LANG
SYST:VERS?
TRIG[:SEQ1 | :TRAN][:IMM]
TRIG[:SEQ1 | :TRAN]:SOUR
TRIG:SEQ2 | ACQ[:IMM]
TRIG:SEQ2 | ACQ:SOUR
TRIG:SEQ:DEF
*CLS
*ESE*ESE?*ESR?
*IDN?
*OPC*OPC?*OPT?
*PSC*PSC?
*RCL*RST
*SAV*SRE*STB?
*TRG*TST?
*WAI