Page 1 Installation and Maintenance Guide BCM50 3.0 Business Communications Manager Document Status: Standard Document Number: NN40020-302 Document Version: 02.03 Date: December 2009...
Page 2 Nortel Networks. Trademarks Nortel, the Nortel logo, and the Globemark are trademarks of Nortel Networks. Microsoft, MS, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation. All other trademarks and registered trademarks are the property of their respective owners.
Page 3 THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE, RETURN THE UNUSED SOFTWARE AND THE ASSOCIATED DOCUMENTATION TO NORTEL NETWORKS THROUGH A NORTEL NETWORKS AUTHORIZED DISTRIBUTOR WITHIN FIVE (5) DAYS OF YOUR ACQUISITION OF THE SOFTWARE FOR A REFUND.
Page 4 License. NORTEL NETWORKS. If NORTEL NETWORKS (i) claims a material breach of this License, and Open source copyright (ppp-2.4) (ii) provides written notice of such claimed material breach to...
Page 5 Copyright 1992 Livingston Enterprises, Inc. Livingston Enterprises, Inc. 6920 Koll Center Parkway Pleasanton, CA 94566 Permission to use, copy, modify, and distribute this software for any purpose and without fee is hereby granted, provided that this copyright and permission notice appear on all copies and supporting documentation, the name of Livingston Enterprises, Inc.
Page 6 NN40020-302...
Page 7: Table Of Contents
Task List New in this release ..........19 Regulatory information .
Page 8 Task List To connect the music source using the RJ-21 telephony connector ......116 To connect the cables to the wiring field card (optional) ..........117 To connect the cables to the patch panel (optional) ............117 Installing telephones and peripherals ......119 To install the emergency telephone................120 Installing the analog terminal adapter .
Page 9 Task List To connect the BCM50 system to the LAN ..............161 To connect the BCM50e or BCM50be main units to the WAN ........162 To connect the BCM50a or BCM50ba main units to the WAN ........162 Testing basic BCM50 functionality ......165 To test the main unit ....................165 To troubleshoot the main unit ..................166 To test the expansion unit ...................166...
Page 10 Task List To insert the new router card..................203 To close the main unit case ..................204 RJ-21 telephony connector wiring chart ......207 BRI wiring chart .
Page 11 Contents New in this release..........19 Features .
Page 12 Contents Power supply mounting bracket and enclosure ......54 Wiring field card ..........54 BCM50 components .
Page 13 Contents Basic hardware ........... 79 Optional equipment .
Page 14 Contents Installing an emergency telephone ........120 Installing IP phones .
Page 15 Contents Configuring voice mail ..........157 Customizing security policies .
Page 16 Contents Chapter 24 Replacing an internal component ....... 193 Special tools ............194 Preparing the system for maintenance .
Page 17 Contents ATA2 parameters ........... 262 ATA2 DR6 .
Page 18 Contents NN40020-302...
Page 19: New In This Release
New in this release New in this release The following sections detail what’s new in Device Configuration Guide Standard 02.04 Business Communications Manager for release 3.0. • Features on page 19 • Other changes on page 19 Features This release contains no new features. Other changes Revision history December 2009...
Page 20 New in this release NN40020-302...
Page 21: Regulatory Information
Do not attempt to repair this equipment. If you experience trouble, write for warranty and repair information: Canada Nortel Nortel Repair Service Centre 30 640 Massman Drive 30 Norelco Drive Nashville, TN, USA Weston Ontario, Canada 37210 M9L 2X6 For warranty and repair service outside the USA or Canada, please contact your distributor.
Page 22: Federal Communications Commission (Fcc) Notice
Regulatory information Federal Communications Commission (FCC) Notice FCC registration number: This telephone equipment complies with Part 68, Rules and Regulations, of the FCC for connection to the Public Switched Telephone Network. Your connection to the Public Switched Telephone Network must comply with these FCC rules: •...
Page 23: Important Safety Instructions
Regulatory information Important safety instructions The following safety instructions cover the installation and use of the Product. Read carefully and retain for future reference. Installation Warning: To avoid electrical shock hazard to personnel or equipment damage observe the following precautions when installing telephone equipment: •...
Page 24: Safety
Music On Hold or Background Music features of this telecommunication system. Nortel hereby disclaims any liability arising out of the failure to obtain such a license. Safety Business Communications Manager 50 (BCM50) equipment meets all applicable requirements of both the CSA C22.2 No.60950 and UL 60950 Edition 3.
Page 25: Enhanced 911 Configuration
Regulatory information Caution: Only qualified persons should service the system. The installation and service of this hardware is to be performed only by service personnel having appropriate training and experience necessary to be aware of hazards to which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons.
Page 26: International Regulatory Information
NT9T64XX, and NT9T65XX, are in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Information is subject to change without notice. Nortel reserves the right to make changes in design or components as progress in engineering and manufacturing may warrant. This equipment has been tested and found to comply with the European Safety requirements EN 60950 and EMC requirements EN 55022 (Class A) and EN 55024.
Page 27: Safety
(exchange lines) removed first. Additional safety information The following interfaces (TNV) can be connected to the Public Switched Telephone Network in accordance with Nortel and the local carriers installation requirements: • BCM50, CSC GATi Ports integrated (Loop Start) •...
Page 28: Itu Standardization Compliance
BCM50, CSC USB Port • BCM50, CSC Ethernet Port including optional Ethernet Hub Ports ITU standardization compliance The following list provides voice/data applications and telephony support for BCM50 3.0: • G.711 and G.729AB codecs • V.27ter, V.29, and V.17 data modem modulation supported (T.38 fax control gateway) •...
Page 29: Getting Started
The concepts, operations, and tasks described in this guide relate to the hardware of the BCM50 system. This guide provides task-based information about installing the hardware components and performing basic configuration tasks. Use Nortel Business Element Manager, Startup Profile, and Telset Administration to configure various BCM50 parameters. In brief, the information in this guide explains: •...
Page 30 Global analog station module (global analog station media bay module) GATM Global analog trunk module (global analog trunk media bay module) Key expansion module Key indicator module Keycode retrieval system (Nortel keycode retrieval system) Local area network Line isolation unit Media bay module Media services card...
Page 31: Symbols And Text Conventions
Wide area network Symbols and text conventions These symbols highlight critical information for the BCM50 3.0 system. Caution: Alerts you to conditions where you can damage the equipment. Danger: Alerts you to conditions where you can get an electrical shock.
Page 32 Chapter 1 Getting started Note: Alerts you to important information. Tip: Alerts you to additional information that can help you perform a task. Security Note: Indicates a point of system security where you can change a default, or where the administrator must decide on the level of security required for the system.
Page 33: Related Publications
33 and User Guides on page 34. Technical Documents System Installation BCM50 3.0 Upgrade Guide (NN40020-401) Installation Checklist and Quick Start Guide (NN40020-308) Keycode Installation Guide (NN40010-301) R2MFC Media Bay Module Installation and Configuration Guide (NN40010-300) System Programming...
Page 34: How To Get Help
Getting Help over the phone from a Nortel Solutions Center If you don’t find the information you require on the Nortel Technical Support Web site, and have a Nortel support contract, you can also get help over the phone from a Nortel Solutions Center.
Page 35 To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: http://www.nortel.com/erc...
Page 36 Chapter 1 Getting started NN40020-302...
Page 37: Introducing The Bcm50 Hardware
Chapter 2 Introducing the BCM50 hardware The Business Communications Manager 50 Release 3.0 (BCM50 3.0) provides private network and telephony management capability to small- and medium-sized businesses. The BCM50 system: • integrates voice and data capabilities, IP Telephony gateway functions, and data-routing features into a single telephony system •...
Page 38 Chapter 2 Introducing the BCM50 hardware — BCM50a main unit (with ADSL router) The BCM50a main unit provides all the same core functionality as the BCM50 main unit, and it has an integrated ADSL router for advanced data applications. For detailed configuration information, see the BCM50a Integrated Router Configuration Guide.
Page 39 Chapter 2 Introducing the BCM50 hardware Figure 1 BCM50 main unit ports and connectors Expansion/LAN Music (port 1) (port 0) (port 2, port 3) source Retention clip mounting hole Power Reset RJ-21 telephony switch connector Figure 2 BCM50a main unit ports and connectors Additional LAN Retention clip mounting hole...
Page 40 Chapter 2 Introducing the BCM50 hardware Figure 4 BCM50b main unit ports and connectors Expansion/LAN Music BRI ports (port 1) (port 0) (port 2, port 3) source Retention clip mounting hole Power Reset RJ-21 telephony switch connector Figure 5 BCM50ba main unit ports and connectors Additional LAN BRI ports Retention clip...
Page 41 Chapter 2 Introducing the BCM50 hardware Table 1 Main unit ports/connectors and descriptions Port/connector Description Power connector A barrel connector jack used to connect the power supply to the main unit. Retention clip mounting hole A small hole into which you insert the retention clip. The retention clip secures the power connector to the unit.
Page 42: Bcm50 Expansion Unit And Media Bay Modules
Chapter 2 Introducing the BCM50 hardware Warning: External equipment connected to the auxiliary ringer, page relay, page output, and music-on-hold interfaces must use safety extra low voltage (SELV). All four interfaces are SELV, and the external equipment connected to these interfaces must be SELV.
Page 43 Chapter 2 Introducing the BCM50 hardware Table 2 BCM50 expansion unit ports, connectors, and descriptions (Sheet 2 of 2) Port/connector Description Retention clip mounting hole A small hole into which you insert the retention clip. The retention clip secures the power connector to the expansion unit.
Page 44: Media Bay Modules
Chapter 2 Introducing the BCM50 hardware Note: When generating your keycode, you must select the feature for the expansion ports you require. If your keycode contains the feature for one expansion port only, the expansion port on the left (port 2) is active. Media bay modules The media bay modules (MBM) connect with external devices to implement various types of voice trunks and extensions.
Page 45 BCM50 system. Table 3 Trunk MBMs Module type Function Special notes Connects digital public switched Can connect to T1 or PRI-E1/T1 telephone lines to the BCM50 3.0 interfaces. (see Digital trunk media bay system. module on page 45)
Page 46 Chapter 2 Introducing the BCM50 hardware Figure 10 DTM faceplate Monitor jacks RJ-48C digital telephone line connector Basic rate interface media bay module The basic rate interface media bay module (BRIM) connects a maximum of four BRI ISDN loops to the BCM50 system. The BRIM recognizes only the T-interface used in European networks. To use the BRIM with the U-interface, typical in North American networks, you require an external NT1 box to convert the U-interface to a T-interface.
Page 47 Chapter 2 Introducing the BCM50 hardware Figure 12 GATM faceplate Analog direct inward dialing media bay module The analog direct inward dialing (ADID) MBM provides an interface for four or eight analog public switched telephone network (PSTN) lines. The ADID MBM supports both pulse and tone dialing as well as disconnect supervision, and direct inward dialing call progress signaling as described in standard TIA-464C.
Page 48 Chapter 2 Introducing the BCM50 hardware Table 4 Station MBMs (Sheet 2 of 2) Module type What it does Special Notes G4x16/G8x16 Connects a maximum of four (G4x16) or — eight (G8x16) analog public switched Combination of a GATM4/GATM8 and a telephone lines to the BCM50 system.
Page 49 Chapter 2 Introducing the BCM50 hardware Figure 15 4x16 faceplate LEDS and connectors G4x16 and G8x16 media bay module The G4x16 MBM is a combination of GATM4 and DSM16 MBMs, while the G8x16 is a combination of GATM8 and DSM16 MBMs. The figure G4x16/G8x16 faceplate LEDS and connectors on page 49 shows the G4x16/G8x16...
Page 50 Chapter 2 Introducing the BCM50 hardware • Enhanced ringing capability: ASM8+ and GASM provide a ringing voltage of 2 REN/65 V rms per port. • The GASM8 is designated as an on-premise station (ONS) port. This device provides telecommunications ringing voltages and can be configured to provide voltage message waiting indicator (VMWI) voltage levels.
Page 51 Chapter 2 Introducing the BCM50 hardware The table ATA2, ASM8, ASM8+, GASM, and GASI analog device specifications on page 51 shows the specifications for ATA2, ASM8, GASM, and GASI. Table 5 ATA2, ASM8, ASM8+, GASM, and GASI analog device specifications (Sheet 1 of 2) Specification ATA2 ASM8...
Page 52: Bcm50 Hardware
Chapter 2 Introducing the BCM50 hardware Table 5 ATA2, ASM8, ASM8+, GASM, and GASI analog device specifications (Sheet 2 of 2) Specification ATA2 ASM8 ASM8+ GASM GASI MWI type (see Note) Stutter tone Stutter tone Stutter tone/ Stutter tone/ Stutter Tone/ Voltage MWI Reverse polarity/ Reverse polarity/...
Page 53: Patch Panel
Chapter 2 Introducing the BCM50 hardware Patch panel The BCM50 patch panel simplifies the connections of lines and extensions to the main unit. The BCM50 patch panel installs into the rack-mount shelf in a standard equipment rack and connects to the RJ-21 telephony connector with a user-supplied RJ-21 cable. See the figure Patch panel connectors on page 53.
Page 54: Power Supply Mounting Bracket And Enclosure
Chapter 2 Introducing the BCM50 hardware Power supply mounting bracket and enclosure There are two BCM50 power supply mounting options that enable you to install your power supply units next to your BCM50 system and keep the power cables neatly organized: •...
Page 55: Power Supply
Chapter 2 Introducing the BCM50 hardware • Hard disk on page 56 • Router card on page 59 • Cooling fan on page 57 • RJ-21 telephony connector on page 58 Power supply The power supply is an external device that connects to the BCM50 units. See the figure BCM50 power supply on page 55.
Page 56: Hard Disk
Chapter 2 Introducing the BCM50 hardware The BCM50 supports American Power Conversion (APC) UPS devices that use a USB control interface. The APC UPSs include the APC UPS-Smart family (for example, UPS-Smart 750 and UPS-Smart 1000) and UPS-Back family (for example, UPS-Back 500 ES and UPS-Back 350 ES). You can use the UPS control software to configure various operational settings.
Page 57: Cooling Fan
Chapter 2 Introducing the BCM50 hardware Figure 23 Hard disk and bracket Hard disk Hard disk bracket Cooling fan The main units have one cooling fan. The expansion unit has two cooling fans. See the figure Cooling fan on page 57. Figure 24 Cooling fan fan connector The cooling fan mounts in the back of the BCM50 enclosure.
Page 58: Rj-21 Telephony Connector
Chapter 2 Introducing the BCM50 hardware RJ-21 telephony connector Use the RJ-21 telephony connector to connect a 25-pair (RJ-21) cable to the main unit. Then use these 25 pairs of wires to connect to the following telephony devices (see RJ-21 telephony connector wiring chart on page 207): •...
Page 59: Router Card
Chapter 2 Introducing the BCM50 hardware Router card The BCM50e main unit has a router card that uses an Ethernet interface to connect to a WAN edge device (for example, an external ADSL modem or a cable modem). The BCM50a main unit has a router card that uses an ADSL interface to connect the BCM50 system to the Internet Service Provider (ISP).
Page 60: Accessories
Chapter 2 Introducing the BCM50 hardware Table 7 Media bay modules (Sheet 2 of 2) Component description FRU Description Installation procedure G4x16/G8x16 MBM “G4x16 and G8x16 media bay “To install an MBM” module” GASM MBM “Analog station media bay modules” “To install an MBM”...
Page 61: Viewing The Bcm50 System Leds
Chapter 3 Viewing the BCM50 system LEDs Chapter 3 Viewing the BCM50 system LEDs This section describes the BCM50 system LEDs including BCM50 main unit, expansion unit, and media bay module (MBM) LEDs. For information about the BCM50 system LEDs: •...
Page 62 Chapter 3 Viewing the BCM50 system LEDs Figure 25 Location of system status LEDs on a main unit Status LED Power LED The table System status LEDs states and descriptions on page 62 describes the meaning of the system status LEDs after the system boots up and is in service. Table 8 System status LEDs states and descriptions Power Status...
Page 63: Lan Port Leds
Chapter 3 Viewing the BCM50 system LEDs Table 9 System status LEDs during startup or reboot Power Status Description Solid green Flashing green Administrator can log into BCM50 with Element Manager. Solid green Solid green All BCM50 services are functioning, and the system is ready for normal use.
Page 64: Adsl Router Leds (Bcm50A And Bcm50Ba Only)
Chapter 3 Viewing the BCM50 system LEDs The table LAN port and expansion port LED indicators on page 64 describes the possible LED states for the LAN ports LEDs. Table 10 LAN port and expansion port LED indicators Status Description Yellow The LAN port is operating at 10 Mb/s.
Page 65: Ethernet Router Leds (Bcm50E And Bcm50Be Only)
Chapter 3 Viewing the BCM50 system LEDs Table 11 ADSL router LED descriptions (Sheet 2 of 2) Status Description The router card is linked successfully to a digital subscriber line access multiplexer (DSLAM). The DSL link is not functioning. Flashing The router card is initializing the DSL line.
Page 66: Bri Port Leds On Main Unit (Bri Series Only)
Chapter 3 Viewing the BCM50 system LEDs BRI port LEDs on main unit (BRI series only) The three BRI port LEDs on the BCM50b, BCM50ba, and BCM50be main units monitor the BRI port status. The figure Ethernet router LEDs on the BCM50e and BCM50be main units (BCM50e shown) on page 65 shows the location of the BRI ports and LEDs.
Page 67: Dtm Leds
Chapter 3 Viewing the BCM50 system LEDs The table MBM LED descriptions on page 67 describes the possible MBM LED states. Table 14 MBM LED descriptions Power Status Description The MBM has no power, or a failure occurred on the MBM power converter. BCM50 to expansion unit failure or system initialization.
Page 68: Brim Leds
Chapter 3 Viewing the BCM50 system LEDs Table 15 DTM LED functions (Sheet 2 of 2) Status Descriptions In service Flashing The T1, ETSI, or PRI trunks are out of service because a loopback test is running or the DTM is initializing. Loopback test A continuity loopback test is running.
Page 69: Determining Dhcp Server Configuration And Ip Address
Each main unit has a DHCP) server. This DHCP server supplies Nortel IP Phones and client computers with IP addresses and connection information. If the main unit has no integrated router, then you can configure the DHCP server using Element Manager.
Page 70: If An External Dhcp Server Is Present
Chapter 4 Determining DHCP server configuration and IP address If an external DHCP server is present Warning: The DHCP server on the main unit is enabled (IP Phones only) by default. If your network already contains a DHCP server, then disable the DHCP server on the main unit.
Page 71 Chapter 4 Determining DHCP server configuration and IP address By default, the router LAN IP address is 192.168.1.1, and the IP address assigned to the BCM50 system is the first IP address in the DHCP pool. If the DHCP pool starts at 192.168.1.190, then the BCM50 is 192.168.1.190 even though the router is 192.168.1.1.
Page 72 Chapter 4 Determining DHCP server configuration and IP address NN40020-302...
Page 73: Installing The Bcm50 System
Chapter 5 Installing the BCM50 system Chapter 5 Installing the BCM50 system To install a BCM50 system, you must install a BCM50 main unit, any expansion units required, and the telephony components. The figure BCM50 installation overview on page 73 and the table BCM50 installation overview on page 74 provide an overview of the installation process.
Page 74 Chapter 5 Installing the BCM50 system Table 16 BCM50 installation overview (Sheet 1 of 2) Tasks Description Refer to Prepare for installation Verify these requirements: Checking the installation prerequisites on page 77 • environmental • electrical • site telephony wiring Get required equipment Ensure you have these items: System equipment,...
Page 75 Chapter 5 Installing the BCM50 system Table 16 BCM50 installation overview (Sheet 2 of 2) Tasks Description Refer to Install telephones and You can install these telephones: Installing telephones and peripherals peripherals on page 119 • System telephones • Emergency telephone •...
Page 76 Chapter 5 Installing the BCM50 system NN40020-302...
Page 77: Checking The Installation Prerequisites
Chapter 6 Checking the installation prerequisites Chapter 6 Checking the installation prerequisites Before you install a main unit or expansion unit, perform the following tasks: • Determine the location for the BCM50 units, telephones, and other equipment based on space and electrical requirements.
Page 78: Site Telephony Wiring Requirements
(including power bar) must not exceed 2 m (6.5 ft.). You must use a power bar approved by an appropriate National Test Body, with a third-wire ground. Nortel recommends that you do not use an extension cord between the power supply and the power bar or between the power bar and the electrical outlet.
Page 79: System Equipment, Supplies, And Tools
Chapter 6 Checking the installation prerequisites System equipment, supplies, and tools For the equipment required to install the BCM50 system: • Basic hardware on page 79 • Optional equipment on page 79 • Other hardware and tools on page 79 Basic hardware The BCM50 system comprises a combination of the following hardware: •...
Page 80 Chapter 6 Checking the installation prerequisites • surge protector (recommended) • cables, 25-pair cable with right-feeding female RJ-21 connectors • 3.5-mm mono audio jack (for external music source) NN40020-302...
Page 81: Installing The Main Unit
Chapter 7 Installing the main unit This section describes how to install the main unit. You can install the main unit in an equipment rack, on a wall, or on a desktop. The figure Overview of installing the main unit on page 81 shows the steps required to install the main unit.
Page 82: Unpacking The Main Unit
Installation Checklist and Quick Start Guide Visually inspect the components for damage during shipping. If you find damage, contact your Nortel sales representative. Installing the BCM50 unit in an equipment rack You can install a BCM50 main unit in a standard 19-inch equipment rack along with your other networking and telecommunications equipment.
Page 83: To Install The Rack-Mount Shelf In An Equipment Rack
Chapter 7 Installing the main unit Caution: To keep the BCM50 system operating at the optimal internal temperature, keep the top, sides, and rear clear of obstructions and away from the exhaust of other equipment. Place no objects, except another BCM50 unit or a power supply mounting enclosure, on top of the main unit.
Page 84: To Install The Bcm50 Unit On The Rack-Mount Shelf
If you install additional units, you can install a second unit on the shelf beside the first unit. You can install another unit on top of each of the first two units. Nortel recommends a maximum of four units per rack-mount shelf.
Page 85: To Install A Bcm50 Unit On Top Of Another Unit
Chapter 7 Installing the main unit To install a BCM50 unit on top of another unit Insert the power supply retention clip into the BCM50 unit. Place the BCM50 unit on top of the other unit. Make sure the feet of the unit are in the slots on the top of the unit and in front of the slots.
Page 86: To Install The Bcm50 Wall-Mount Bracket
Use a pencil to mark the location of the plywood backboard on the wall. Use a ruler and a level to make sure that the plywood backboard is level. Note: Nortel recommends the use of a plywood backboard to simplify installing multiple BCM50 units. However, due to the compact size and light weight of the BCM50 units, a backboard is not required.
Page 87 • Two screws mount through the cable trough (open the cable-management door). • Three screws mount as shown in the figure. Note: When you use three screws, Nortel recommends installing the screws in the three holes labeled “1” or the three holes labeled “2”.
Page 88: To Install The Bcm50 Unit On The Wall-Mount Bracket
Chapter 7 Installing the main unit g Install two screws into the screw holes in the cable trough. If the BCM50 system has only one unit, go to the procedure To install the BCM50 unit on the wall-mount bracket on page 88. If the BCM50 system has more than one unit, repeat steps 3 to 6 for each wall-mount bracket.
Page 89 Chapter 7 Installing the main unit Figure 40 Attach the BCM50 unit to the wall-mount bracket Press the unit against the wall-mount bracket and slide the unit down until it clicks in place. Slide the wall-mount lock to the left (lock position). See the figure Wall-mount lock in lock position on page 89.
Page 90: To Install The Wfc
Chapter 7 Installing the main unit Installing the wiring field card (optional) Install the optional wiring field card (WFC) in the cable-management tray of the main unit. To install the WFC Clear the WFC installation area of all cables. Place the WFC in the installation area with the 50-pin header at the top. Slide the WFC down until it is at the bottom of the installation area and held in place by the three clips.
Page 91: To Install The Bcm50 Unit On A Desktop Or Shelf
Chapter 7 Installing the main unit Installing the BCM50 unit on a desktop or shelf To mount a BCM50 unit on a desktop or shelf, attach the supplied rubber feet to the bottom of the unit. If the BCM50 system includes additional units, you can set the additional units beside, or stack them on top of, the first unit.
Page 92: To Install The Power Supply On The Rack-Mount Shelf
Chapter 7 Installing the main unit If the BCM50 system has additional units, you can install the other units on top of, or beside, the existing BCM50 unit. • To install the additional units beside the existing unit, repeat steps 1 to 3 for each unit. •...
Page 93: To Install The Power Supply On The Desktop
Mount the power supply mounting enclosure in the same manner as your other BCM50 units (in a rack, on a wall, or on a destop). For more detailed installation instructions for the power supply mounting enclosure, see the Nortel BCM50 Power Supply Mounting Enclosure (N0118043).
Page 94 Chapter 7 Installing the main unit NN40020-302...
Page 95: Installing An Expansion Unit
Chapter 8 Installing an expansion unit Chapter 8 Installing an expansion unit Adding an expansion unit increases the capacity of your BCM50 system by providing a method of adding a media bay module (MBM). Each MBM you add increases the number of public switched telephone network (PSTN) trunks or extensions that you can connect to the BCM50 system.
Page 96: Unpacking The Expansion Unit
• four rubber feet Visually inspect the components for damage during shipping. If you find damage, contact your Nortel representative. Warning: Make sure the power supply to the expansion unit is disconnected before inserting or removing an MBM. Verifying the media bay module switch settings Each MBM has dip switches on the back or underside of the module.
Page 97 Chapter 8 Installing an expansion unit Figure 46 Switches on the media bay module (not applicable for GASM or GATM) Underside of MBM 6 5 4 3 2 1 1 2 3 4 5 6 Top of MBM dip switches Back of MBM Rear view of MBM Note: The GASM and GATM MBMs have a dip switch configuration different...
Page 98: To Set G4X16 Or G8X16 Dip Switches
Chapter 8 Installing an expansion unit To set G4x16 or G8x16 dip switches Set the Module Select dip switches to on (up). See the figure G4x16/G8x16 dip switch location on page 98. Set the Mode/Country Select dip switches to off (down); this setting allows the MBM to automatically download the country profile settings.
Page 99: To Set Gatm Dip Switches
Chapter 8 Installing an expansion unit Table 19 GASM dip switch settings (switch 4–8) Switches 4 to 8 select the region for the GASM as follows: Switch 4 Switch 5 Switch 6 Switch 7 Switch 8 North America United Kingdom Australia Poland After you set the switches, proceed to...
Page 100: To Install An Mbm
Digital Station ports DSM16+, DSM32+, and Analog Station ports GASM8 must not be connected to exposed plant. This includes Digital Station ports residing on the Combination MBMs G4x16 and G8x16. Use only proprietary Nortel Digital Station Sets for connection to digital ports and agency approved Analog devices for connection to the Analog Station ports.
Page 101: Installing The Expansion Unit
Chapter 8 Installing an expansion unit Installing the expansion unit Make sure that the expansion unit is installed close enough to the main unit so that the supplied expansion cable can be connected between the expansion unit and main unit. The expansion unit can be mounted in a rack, on a wall, or on a desktop.
Page 102 Chapter 8 Installing an expansion unit NN40020-302...
Page 103: Connecting The Cables To The Bcm50 System
Chapter 9 Connecting the cables to the BCM50 system Chapter 9 Connecting the cables to the BCM50 system This section describes how to connect the telephone lines, telephony devices, and power to the BCM50 system. The figure Overview of connecting cables to the BCM50 system on page 103 shows the steps required to connect the cables to the BCM50 system.
Page 104: Connecting The Expansion Unit
Chapter 9 Connecting the cables to the BCM50 system For information about connecting the cables to the BCM50 system: • Connecting the expansion unit on page 104 • Connecting the power supply on page 106 • Connecting the lines and extensions on page 108 •...
Page 105: To Connect An Expansion Unit
Chapter 9 Connecting the cables to the BCM50 system If your BCM50 system does not have an expansion unit, proceed to Connecting the power supply on page 106. To connect an expansion unit Note: Keycodes are required for the expansion ports to function. If you purchase a keycode for one expansion port only, expansion/LAN port 2 (on the left) is active.
Page 106: Connecting The Power Supply
Chapter 9 Connecting the cables to the BCM50 system The expansion port you select determines the line and extension numbers of the devices connected to the expansion unit. For the default line and extension numbers, see the table Default line and extension numbers on page 106.
Page 107: To Connect A Power Supply Using A Ups
Rotate the retention clip so the power outlet is open. Plug the power supply cord into the BCM50 unit. Note: Use only the power supply that is approved by Nortel for use with the BCM50 units. Installation and Maintenance Guide...
Page 108: Connecting The Lines And Extensions
Chapter 9 Connecting the cables to the BCM50 system Rotate the retention clip so that it locks the power supply cord in place. Plug one end of the power supply cable into the power supply. Plug the other end of the power supply cable into the AC power source (wall outlet). Repeat steps 1 to 6 for each BCM50 unit.
Page 109: Wiring Warnings
Chapter 9 Connecting the cables to the BCM50 system Wiring warnings Read the following warnings before you connect any telephone lines or extensions to the BCM50 system. Warning: Electrical shock warning The MBMs are safety approved for installation into the expansion unit. The installer and user must ensure that installation of the hardware does not compromise existing safety approvals.
Page 110: To Connect The Lines And Extensions
Chapter 9 Connecting the cables to the BCM50 system Danger: Electrical shock hazards Electrical shock hazards from the telecommunications network and AC mains are possible with this equipment. To minimize risk to service personnel and users, you must connect the BCM50 system to an outlet with a third-wire ground. In addition, all unused slots must have blank faceplates installed.
Page 111: To Connect Telephone Lines To Dtm, Brim, Or 4X16 Mbms
Chapter 9 Connecting the cables to the BCM50 system Select the appropriate option for your system: • If your BCM50 system has an expansion unit, proceed to Connecting telephone lines to the expansion units on page 111 or Connecting extensions to the expansion units on page 112.
Page 112: To Connect Analog Telephone Lines To The Gatm4/Gatm8 Or G4X16/G8X16
Chapter 9 Connecting the cables to the BCM50 system • If your BCM50 system has no other expansion unit, proceed to Connecting the auxiliary equipment on page 113. To connect analog telephone lines to the GATM4/GATM8 or G4x16/G8x16 Read the warnings in Wiring warnings on page 109.
Page 113: To Connect Extensions To Dsm16, Dsm32, Asm8, 4X16, G4X16, Or G8X16 Mbms
Chapter 9 Connecting the cables to the BCM50 system To connect extensions to DSM16, DSM32, ASM8, 4x16, G4x16, or G8x16 MBMs Read the warnings in the Wiring warnings on page 109 section. Obtain a 25-pair cable with an RJ-21 connector on one end. Plug the RJ-21 connector of the cable into the RJ-21 connector on the front of the MBM.
Page 114: To Install An Auxiliary Ringer
Chapter 9 Connecting the cables to the BCM50 system Connecting an auxiliary ringer An auxiliary ringer is a customer-supplied piece of hardware that provides external ringing capability to telephones on the BCM50 system. To install an auxiliary ringer Use the installation instructions supplied with the ringer hardware to install the auxiliary ringer.
Page 115: Connecting An External Music Source
Chapter 9 Connecting the cables to the BCM50 system Connect the paging system relay to the page relay output on the RJ-21 telephony connector. To determine which pair of wires to use for the page relay output, see RJ-21 telephony connector wiring chart on page 207.
Page 116: To Connect The Music Source Using The Music Source Jack
Chapter 9 Connecting the cables to the BCM50 system The music source jack is on the front of the main unit. If you use the music source jack to connect the music source, do not connect a music source to the music source pair on the RJ-21 telephony connector.
Page 117: To Connect The Cables To The Wiring Field Card (Optional)
Chapter 9 Connecting the cables to the BCM50 system Tip: You can adjust the background music volume at every telephone. Select the appropriate option for your system: • If you add more auxiliary equipment, proceed to Connecting an external paging system page 114 or Connecting an auxiliary ringer on page 114.
Page 118: Next Step
Chapter 9 Connecting the cables to the BCM50 system Use a small slotted screwdriver to unscrew the wire hole screws on top of the terminal block. Insert the bare wire ends (6 mm or 0.25 in.) in the appropriate holes on the sides of the terminal block.
Page 119: Installing Telephones And Peripherals
Chapter 10 Installing telephones and peripherals This section describes how to install telephones and peripherals. You can add telephones and peripherals before or after you initialize your system. Which station media bay module (MBM) you use determines your telephone configuration. When you initialize the BCM50, it creates default settings for telephone DN records.
Page 120: To Install The Emergency Telephone
Chapter 10 Installing telephones and peripherals For the requirements and procedure to install the device, see Installing the analog terminal adapter on page 121. Installing an emergency telephone You can use the emergency telephone to make calls when no power is available to the BCM50 system.
Page 121: Installing The Analog Terminal Adapter
Chapter 11 Installing the analog terminal adapter This section provides installation instructions for the analog terminal adapter 2 (ATA2) or ATA. The ATA2 connects a standard analog voice device or data communication device to the BCM50 system through a digital station module. Examples of analog voice devices are analog telephones and answering machines.
Page 122: Analog Data Device
Chapter 11 Installing the analog terminal adapter Analog data device The ATA2 connects a standard analog data device, such as a fax or modem, to the BCM50 system. The figure Data communication device installation overview on page 122 shows an installation overview for connecting a data communication device through an ATA2 to the BCM50 system.
Page 123: To Connect The Ata2
Chapter 11 Installing the analog terminal adapter Figure 56 ATA2 pin outs Line jack Terminal jack TCM* Ring (B-Lead) TCM* Tip (A-Lead) * The TCM input is not polarity sensitive. To connect the ATA2 Connect one end of a line cord to the ATA2 terminal jack. Connect the other end to your telephone, modem, or fax.
Page 124: Test Insertion Loss Measurement
Chapter 11 Installing the analog terminal adapter Figure 57 ATA2 back view Mounting keyhole slots Test insertion loss measurement The maximum loss for ATA2 to Central Office (CO) configuration must not exceed 10 dB. See the figure Insertion loss from the CO to the analog telephone on page 124.
Page 125: To Measure The Insertion Loss From The Co To The Analog Device
Chapter 11 Installing the analog terminal adapter To measure the insertion loss from the CO to the analog device Establish a connection to the 1 mW, 1 kHz, CO service line with an analog telephone attached to the ATA2. Ensure that the analog port terminates correctly in 600 ohms: •...
Page 126 Chapter 11 Installing the analog terminal adapter NN40020-302...
Page 127: Configuring The Bcm50 System
Chapter 12 Configuring the BCM50 system Chapter 12 Configuring the BCM50 system This section provides information about configuring the basic BCM50 parameters. You can configure advanced parameters using Element Manager or Telset Administration after the BCM50 system is operational. The figure Overview of configuring the basic BCM50 parameters on page 127 shows an overview of configuring the basic BCM50 parameters.
Page 128: Initial Parameters Overview
Chapter 12 Configuring the BCM50 system Initial parameters overview The initial parameters are the required parameters that you can configure using Telset Administration, Element Manager, or the Startup Profile. See the table Initial parameters on page 128 for a list of the initial parameters. Table 21 Initial parameters Parameters Telset Administration...
Page 129: Startup Parameters Overview
Chapter 12 Configuring the BCM50 system Startup parameters overview The startup parameters are the remaining required parameters that you cannot configure using Telset Administration. You must configure these parameters using Element Manager or the Startup Profile. See the table Startup parameters on page 129 for a list of the startup parameters.
Page 130 Chapter 12 Configuring the BCM50 system Table 22 Startup parameters (Sheet 2 of 2) Parameters Telset Administration Element Manager Startup Profile User account: Configuration > User Account Administrator Access > • User ID View by Accounts tab • Group • Description •...
Page 131: Using Telset Administration To Set The Basic Parameters
Chapter 13 Using Telset Administration to set the basic parameters Chapter 13 Using Telset Administration to set the basic parameters You can use Telset Administration through a digital telephone with a two-line display to set the BCM50 configuration parameters. You cannot set all the basic parameters using Telset Administration. Therefore, after configuring the initial parameters, you must use Element Manager to set the startup parameters.
Page 132: To Enter The Keycodes
Chapter 13 Using Telset Administration to set the basic parameters Configuring the initial parameters Use the following procedures to configure the initial parameters for the BCM50 using Telset Administration: • To enter the keycodes on page 132 • To configure the IP address on page 133 •...
Page 133: To Configure The Ip Address
Chapter 13 Using Telset Administration to set the basic parameters To configure the IP address Select Feature 9*8 from a two-line display telephone. Enter the following user ID and password: User ID: SETNNA Password: CONFIG The numerical values of the user ID and password are 738662 and 266344, respectively. Press NEXT to scroll through the menu and select IP Address.
Page 134: To Select The Region
Chapter 13 Using Telset Administration to set the basic parameters To select the region Set the Region using Feature **PROFILE from a two-line display telephone. For information about using Telset Administration to set this parameter, see the Telset Administration Guide. To select the telephony startup template and start DN Set the Template and Start DN using Feature **STARTUP from a two-line display telephone.
Page 135: Next Step
Chapter 13 Using Telset Administration to set the basic parameters Press BACK. The Accounts screen appears. Press NEXT. The password screen appears. 10 Press CHNGE to change the password. 11 Press NEXT to scroll through the list of available accounts. 12 Press CHNGE to change the password for the selected account.
Page 136 Chapter 13 Using Telset Administration to set the basic parameters NN40020-302...
Page 137: Using Element Manager To Set The Basic Parameters
Chapter 14 Using Element Manager to set the basic parameters Chapter 14 Using Element Manager to set the basic parameters The Element Manager application provides a computer-based client interface that can connect to devices over an IP network and display the programming interface for that device. You can use the latest Element Manager version to manage all previous BCM systems that require Element Manager.
Page 138: To Access The Bcm50 Web Page
Chapter 14 Using Element Manager to set the basic parameters Prerequisites BCM Element Manager has the following system requirements: • Windows: Windows 2000, Windows XP, or Windows Vista • RAM: minimum 256 MB, recommended 512 MB • free space: 150 MB •...
Page 139: To Connect To The Bcm50 System Using Element Manager
Chapter 14 Using Element Manager to set the basic parameters To connect to the BCM50 system using Element Manager Open Element Manager. From the Network menu, select New Network Element, and then select Business Communications Manager. Enter the BCM50 system IP address in the dialog box (default is 10.10.10.1). Click OK.
Page 140: To Configure The Lan Ip Address
Chapter 14 Using Element Manager to set the basic parameters To configure the LAN IP address From the Configuration tab, click the System folder to expand it. Select IP Subsystem. Select the General Settings tab. It is normally selected by default. From the IP Settings area, click Modify.
Page 141: To Initialize Voice Mail
Chapter 14 Using Element Manager to set the basic parameters Configure the Cold Reset Telephony attributes. See the table Cold Reset Telephony attributes on page 141. Table 24 Cold Reset Telephony attributes Attribute Description Region Specify the startup region. Template Specify the startup template.
Page 142: To Configure The Date And Time Settings
Chapter 14 Using Element Manager to set the basic parameters Enter a name for your system in the System name field. To configure the date and time settings From the Configuration tab, click the System folder to expand it. Select Date and Time. The Date and Time panel appears.
Page 143 Chapter 14 Using Element Manager to set the basic parameters Click Launch Router WebGUI tool to launch the router configuration tool. For information about using the router WebGUI tool, see the Integrated Router Configuration Guide for your product. • Clear the Use DHCP Server on Integrated Router check box to use the DHCP server on the main unit.
Page 144: To Configure Ip Phones
Chapter 14 Using Element Manager to set the basic parameters To configure IP Phones From the Configuration tab, click the Resources folder to expand it. Select Telephony Resources. From the Actual Type column, select IP Sets. The Details for Module area appears in the lower pane with the IP Terminal Global Settings tab as the default.
Page 145: To Configure Snmp Settings
Chapter 14 Using Element Manager to set the basic parameters To configure SNMP settings From the Configuration tab, click the Administrator Access folder to expand it. From the Administrator Access folder, select SNMP. Select the General tab. It is normally selected by default. From the SNMP Settings area, click Modify.
Page 146: To Configure The Snmp Manager List
Chapter 14 Using Element Manager to set the basic parameters To configure the SNMP manager list Use the SNMP manager list to specify IP addresses that can connect to the SNMP agent. From the Configuration tab, click the Administrator Access folder to expand it. From the Administrator Access folder, select SNMP.
Page 147: To Configure Srg
Chapter 14 Using Element Manager to set the basic parameters Click OK. Repeat steps 4 to 6 to create more user accounts. To configure SRG From the Configuration tab, click the Resources folder to expand it. Select Survivable Remote Gateway from the Resources folder. Select the S1000 Main Office Settings tab.
Page 148 Chapter 14 Using Element Manager to set the basic parameters NN40020-302...
Page 149: Using The Startup Profile To Configure Parameters
Chapter 15 Using the Startup Profile to configure parameters Chapter 15 Using the Startup Profile to configure parameters An experienced administrator uses the Startup Profile tool to customize a template with common BCM50 parameters. The administrator uses this template to configure a single system or multiple systems.
Page 150: Startup Profile Requirements
If you do not have the Startup Profile template on your computer, you can get a copy from the the Nortel support Web site (www.nortel.com/support) or the Administrator Applications page on the main unit. For details about getting the Startup Profile template from the main unit, see...
Page 151: To Download The Startup Profile Template
Chapter 15 Using the Startup Profile to configure parameters To download the Startup Profile template Access the BCM50 Web page (see the procedure To access the BCM50 Web page on page 138). From the Welcome to BCM Web page, click Administrator Applications. The Administrator Applications page appears.
Page 152: To Load The Startup Profile Data Onto The Bcm50 System
Chapter 15 Using the Startup Profile to configure parameters Note: Never edit the Startup Profile (.sps file) directly; always use the Startup Profile editor to make changes. Enter the remaining information into the Startup Profile editor that you want loaded onto the BCM50 main unit.
Page 153: Next Step
Chapter 15 Using the Startup Profile to configure parameters If an error occurs, the status LED flashes red. View the log file (written to the USB storage device) for a description of the Startup Profile errors. If no errors exist, the BCM50 system automatically reboots to complete the system configuration.
Page 154 Chapter 15 Using the Startup Profile to configure parameters NN40020-302...
Page 155: Completing The Initial Installation (Optional)
Chapter 16 Completing the initial installation (optional) Chapter 16 Completing the initial installation (optional) This section provides information about completing the initial installation of your BCM50 system. These options are described for informative purposes only. The figure Overview of completing the initial installation on page 155 shows an overview of completing the initial installation.
Page 156: To Configure The Mbm(S)
Chapter 16 Completing the initial installation (optional) After the basic configuration finishes, you can further customize your system by using the following configuration options: • Configuring the media bay module on page 156 • Configuring modem settings on page 157 •...
Page 157: Configuring Modem Settings
For information about configuring the modem, see the Networking Configuration Guide. Checking for software updates Nortel frequently updates the BCM50 software. Therefore, a standard part of any installation is to ensure your system has the latest version of the software.
Page 158: Performing A Backup
Chapter 16 Completing the initial installation (optional) For information about customizing the security policies, see the Administration Guide. Performing a backup You can backup your BCM50 system at regular intervals, including after initial installation. Performing a backup ensures that you have a copy of your system data available to restore the system, if needed.
Page 159: Connecting The Bcm50 System To The Lan And Wan
Chapter 17 Connecting the BCM50 system to the LAN and WAN Chapter 17 Connecting the BCM50 system to the LAN and WAN This section describes how to connect the LAN and WAN cables to the BCM50 system. The figure Overview of connecting data networking cables to the BCM50 system on page 159 shows the steps required to connect the data networking cables to the BCM50 system.
Page 160: Connecting The Bcm50 System To The Lan
Chapter 17 Connecting the BCM50 system to the LAN and WAN Connecting the BCM50 system to the LAN On BCM50 and BCM50b main units, three RJ-45 connectors support LAN connections and one OAM port. On the BCM50a, BCM50e, BCM50ba, and BCM50be main units, six RJ-45 connectors support LAN connections and one OAM port.
Page 161: To Connect The Bcm50 System To The Lan
Chapter 17 Connecting the BCM50 system to the LAN and WAN Table 31 LAN ports on the main unit (Sheet 2 of 2) Port name Function Router card The router card LAN ports connect network devices, such as IP telephones to the LAN. LAN ports These ports connect to the network switch built into the main unit.
Page 162: To Connect The Bcm50E Or Bcm50Be Main Units To The Wan
Chapter 17 Connecting the BCM50 system to the LAN and WAN Figure 67 WAN port on a BCM50 main unit BCM50a main unit WAN port BCM50e main unit WAN port For information about connecting the BCM50 to the WAN: • To connect the BCM50e or BCM50be main units to the WAN on page 162 •...
Page 163: Next Step
Chapter 17 Connecting the BCM50 system to the LAN and WAN Warning: Do not plug the WAN cable into the system unless the power supply is connected to the main unit and an AC power source with a third-wire ground. Connect one end of a standard telephone cable to the ADSL telephone line provided by your ISP.
Page 164 Chapter 17 Connecting the BCM50 system to the LAN and WAN NN40020-302...
Page 165: Testing Basic Bcm50 Functionality
Chapter 18 Testing basic BCM50 functionality Chapter 18 Testing basic BCM50 functionality This section describes how to test the BCM50 system. For information about testing and troubleshooting the BCM50 system: • To test the main unit on page 165 • To troubleshoot the main unit on page 166 •...
Page 166: To Troubleshoot The Main Unit
Chapter 18 Testing basic BCM50 functionality To troubleshoot the main unit If a test fails, use the following procedure: Verify that any nonfunctional feature is included in your installed keycode. Check the wiring to the main unit and to the MBMs. Make sure that the cables are properly seated and are connected to the correct ports.
Page 167: To Test The Mbm
Chapter 18 Testing basic BCM50 functionality Check the wiring to the MBM. Make sure that the cables are properly seated and are connected to the correct ports with proper LED indications. Check that the switches on the MBM are all set to on. For more information about these switches, see Verifying the media bay module switch settings on page 96.
Page 168: To Determine Why An Mbm Does Not Appear In Element Manager
Chapter 18 Testing basic BCM50 functionality To determine why an MBM does not appear in Element Manager Check that the correct feature for the expansion unit is included in your installed keycode. Check that both the Power and Status LEDs on the MBM are solid green. •...
Page 169: To Check The Ata2 Wiring
Chapter 18 Testing basic BCM50 functionality To check the ATA2 wiring Use an analog phone to test the ATA2. Check the following connections: ATA2 to the terminal The resistance must be 200 ohms or less for data applications and 1300 ohms or less for voice applications.
Page 170: To Perform A Level 1 And Level 2 Reset
Chapter 18 Testing basic BCM50 functionality • Level 2 reset erases all customer and system configuration data and all software releases and patches. This reset re-installs the original factory configuration settings. Level 2 reset also resets the router firmware to what was shipped from the factory. No Ethernet connectivity to the system occurs during this operation.
Page 171 Chapter 18 Testing basic BCM50 functionality Figure 69 Level 1 and Level 2 reset sequence Reset query state Level 1 reset pending Level 2 reset pending Level 1 reset confirm Perform level 1 reset Level 2 reset confirm Perform level 2 reset System is ready System reboots (Reset request cancelled)
Page 172 Press reset switch; Awaiting Level 2 reset system proceeds to Wait five seconds Flashing red Flashing red confirmation Nortel factory mode (do not use) System performs Level 2 reset; all configuration Solid red Solid red programming and Do not press reset...
Page 173: Replacing The Bcm50 System Components
Chapter 19 Replacing the BCM50 system components Chapter 19 Replacing the BCM50 system components This section provides an overview of how to replace the BCM50 system components. The figure Overview of replacing the BCM50 system components on page 173 shows the steps required to replace the BCM50 system components.
Page 174: To Shut Down The System
Chapter 19 Replacing the BCM50 system components Preparing the system for maintenance Use the following procedure to prepare the system for maintenance. This procedure is referenced throughout the maintenance portion of this document: To shut down the system Check for a recent backup of the BCM50 system programming. If no recent backup is available, then use Element Manager to back up the system data.
Page 175: Replacing A Power Supply
Chapter 20 Replacing a power supply Chapter 20 Replacing a power supply This chapter describes the procedure for replacing a power supply. The figure Overview of replacing the BCM50 power supply on page 175 shows an overview of replacing a power supply. Figure 71 Overview of replacing the BCM50 power supply For information about replacing a power supply: •...
Page 176: To Remove The Power Supply
Chapter 20 Replacing a power supply Preparing the system for maintenance In most cases, if the power supply for the main unit is faulty, the system is already shut down. If this is the case, proceed to Removing the power supply on page 176.
Page 177: To Connect The New Power Supply
Chapter 20 Replacing a power supply To connect the new power supply Connect the new power supply. See Connecting the power supply on page 106. Connect the telephony and data networking lines that you removed in Step 1 of Removing the power supply on page 176.
Page 178 Chapter 20 Replacing a power supply NN40020-302...
Page 179: Replacing A Main Unit
Chapter 21 Replacing a main unit Chapter 21 Replacing a main unit Three types of main units are available: the BCM50, the BCM50a, and the BCM50e. This chapter describes the procedure for replacing a main unit. The figure Overview of replacing a main unit on page 179 shows an overview of replacing a main unit.
Page 180: To Disconnect The Cables
Chapter 21 Replacing a main unit For information about replacing the BCM50 main unit: • Preparing the system for maintenance on page 180 • Removing the main unit on page 180 • Installing the new main unit on page 181 Preparing the system for maintenance In most cases, if the BCM50 main unit is faulty, the system is already shut down.
Page 181: To Remove A Rack-Mounted Main Unit
Chapter 21 Replacing a main unit To remove a rack-mounted main unit Ensure you remove all the cables from the main unit. If necessary, see the procedure To disconnect the cables on page 180. If a unit is mounted to the top of the main unit, slide that unit forward until it disengages from the clips on the main unit.
Page 182: To Connect The Cables
Chapter 21 Replacing a main unit To connect the cables Insert the power supply retention clip into the new main unit. Rotate the power supply retention clip so that the power supply jack is clear. Connect the power supply cord to the main unit. Rotate the power supply retention clip to lock the power supply cord in place.
Page 183: Replacing A Media Bay Module
Chapter 22 Replacing a media bay module Chapter 22 Replacing a media bay module This chapter describes the procedure for replacing a media bay module (MBM). The figure Overview of replacing an MBM on page 183 shows an overview of replacing the MBM.
Page 184: To Remove The Mbm
Chapter 22 Replacing a media bay module To remove the MBM Use Element Manager to disable the MBM. For more information about disabling an MBM, see the Administration Guide. If the expansion unit is wall-mounted, it must be removed from the wall-mount bracket before you remove the MBM.
Page 185: To Insert The New Mbm
Chapter 22 Replacing a media bay module Figure 74 Remove an MBM Grasp the edge of the MBM ejector lever and pull outward Grasp the top and bottom edges of the MBM. Remove the MBM from the expansion unit. Place the MBM on a flat, clean, static-free surface. Warning: Protect the hardware components against damage from electrostatic discharge.
Page 186 Chapter 22 Replacing a media bay module NN40020-302...
Page 187: Replacing An Expansion Unit
Chapter 23 Replacing an expansion unit Chapter 23 Replacing an expansion unit This chapter describes the procedure for replacing an expansion unit. The figure Overview of replacing an expansion unit on page 187 shows an overview of replacing an expansion unit. Figure 75 Overview of replacing an expansion unit Installation and Maintenance Guide...
Page 188: To Disconnect The Expansion Unit Cables
Chapter 23 Replacing an expansion unit For information about replacing an expansion unit: • Disconnecting the cables on page 188 • Removing the expansion unit on page 188 • Removing the MBM on page 190 • Inserting the MBM in the new expansion unit on page 190 •...
Page 189: To Remove A Rack-Mounted Expansion Unit
Chapter 23 Replacing an expansion unit To remove a rack-mounted expansion unit Ensure you remove all the cables from the expansion unit. If necessary, see the procedure To disconnect the expansion unit cables on page 188. If a unit is mounted to the top of the expansion unit, slide that unit forward until it disengages from the clips on the expansion unit.
Page 190: To Remove The Mbm
Chapter 23 Replacing an expansion unit Removing the MBM After you remove the expansion unit, use the following procedure to remove the MBM from the expansion unit. To remove the MBM Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface.
Page 191: To Connect The Cables
Chapter 23 Replacing an expansion unit Installing the new expansion unit Use one of the following procedures to install the new expansion unit: • Installing the BCM50 unit in an equipment rack on page 82 • Installing the BCM50 unit on the wall on page 86 •...
Page 192 Chapter 23 Replacing an expansion unit NN40020-302...
Page 193: Replacing An Internal Component
Chapter 24 Replacing an internal component Chapter 24 Replacing an internal component You can replace three components inside the main unit: the hard disk, the fan, and the router card. The figure Overview of replacing an internal component on page 193 shows an overview of replacing an internal component.
Page 194: Special Tools
Chapter 24 Replacing an internal component For information about replacing an internal component: • Preparing the system for maintenance on page 194 • Removing the main unit on page 194 • Opening the main unit case on page 194 • Removing an internal component on page 196 •...
Page 195: To Open The Main Unit Case
Chapter 24 Replacing an internal component To open the main unit case Danger: Electrical shock warning. Disconnect the power cord, telephone cables, and network cables before opening the BCM50 main unit. Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface.
Page 196: Removing An Internal Component
Chapter 24 Replacing an internal component Figure 79 Remove the top of the case Lift the top of the case off the BCM50 unit. Proceed to Removing an internal component on page 196. Removing an internal component Use one of the following procedures to remove the component: •...
Page 197: To Remove The Hard Disk
Chapter 24 Replacing an internal component To remove the hard disk Caution: Do not use an electric or magnetized screwdriver near the hard disk. You can lose the information stored on the disk. Shock can damage the hard disk. Do not drop or hit the hard disk.
Page 198: To Remove The Fan
Chapter 24 Replacing an internal component Remove the four screws that secure the hard disk to the hard disk bracket. See the figure Hard disk and bracket assembly on page 198. Figure 81 Hard disk and bracket assembly Hard disk Hard disk bracket screws Hard disk bracket Hard disk/power...
Page 199: To Remove The Router Card
Chapter 24 Replacing an internal component Figure 82 Location of fan Lift the fan from the main unit and set it on a flat, clean, static-free surface. Proceed to Inserting the new component on page 199. To remove the router card Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface.
Page 200: To Insert The New Hard Disk
Chapter 24 Replacing an internal component Caution: Use only a Nortel-approved replacement part. Contact your account representative for the current list of approved replacement parts. Warning: Protect the hardware components against damage from electrostatic discharge. Always wear a ground wriststrap before you handle components.
Page 201 Chapter 24 Replacing an internal component Place the new hard disk in the hard disk bracket. Use the four hard disk bracket screws to secure the hard disk to the bracket. Caution: Use only the screws that you removed from the hard disk in the procedure To remove the hard disk on page 197.
Page 202: To Insert The New Fan
Chapter 24 Replacing an internal component Ensure you route the fan cable through the cutouts under the hard disk and bracket. Also, make sure you secure any slack in the fan cable in the clips on the hard disk bracket. See the figure Cable routing on page 202).
Page 203: To Insert The New Router Card
Chapter 24 Replacing an internal component Ensure the fans are oriented so air flows out of the unit. Note: Ensure the label of the new fan faces the back of the BCM50 unit. Air must flow out of the unit as indicated by the arrows imprinted on the fan. Connect the fan cable to the header.
Page 204: To Close The Main Unit Case
Chapter 24 Replacing an internal component Closing the main unit case To close the main unit case Attach one end of a grounding strap to your wrist and the other end to a grounded metal surface. Place the top of the case on top of the main unit case. Make sure the side edges of the case are aligned and the front of the top is back about 1 cm (3/8 in.).
Page 205: Installing The Main Unit
Chapter 24 Replacing an internal component Installing the main unit Use one of the following procedures to install the BCM50 main unit: • Installing the BCM50 unit on the rack-mount shelf on page 83 • To install the BCM50 unit on the wall-mount bracket on page 88 •...
Page 206 Chapter 24 Replacing an internal component NN40020-302...
Page 207: Rj-21 Telephony Connector Wiring Chart
Appendix A RJ-21 telephony connector wiring chart Appendix A RJ-21 telephony connector wiring chart You can connect 4 analog telephone lines (standard main units only), 4 analog telephony devices, and 12 digital telephones to the RJ-21 telephony connector. Note: The four analog lines on the RJ-21 telephony connector are available only on the standard main units.
Page 208 Appendix A RJ-21 telephony connector wiring chart Table 34 RJ-21 telephony connector wiring (Sheet 2 of 3) Default line Device Connection Wire color Type of device Port Default DN number White-Slate Analog — telephone Ring Slate-White Red-Blue Analog — telephone Ring Blue-Red Red-Orange...
Page 209 Appendix A RJ-21 telephony connector wiring chart Table 34 RJ-21 telephony connector wiring (Sheet 3 of 3) Default line Device Connection Wire color Type of device Port Default DN number Violet-Green Digital — telephone Ring Green-Violet Violet-Brown Digital — telephone Ring Brown-Violet Violet-Slate...
Page 210 Appendix A RJ-21 telephony connector wiring chart NN40020-302...
Page 211: Bri Wiring Chart
Appendix B BRI wiring chart Appendix B BRI wiring chart The digital BRI ISDN lines connects to the BCM50b, BCM50ba, and BCM50be main units through the BRI ports (RJ-45) on the front of the main units. See the figure BRI ports and pin out (BCM50b shown) on page 211.
Page 212 Appendix B BRI wiring chart Table 36 BRI line numbering Default line numbers on Default line numbers on Port number Expansion port 1 Expansion port 2 065 – 066 095 – 096 067 – 068 097 – 098 069 – 070 099 –...
Page 213: Lan Ports Wiring Chart
Appendix C LAN ports wiring chart Appendix C LAN ports wiring chart All BCM50 units have LAN ports as follows: • The BCM50 and BCM50b have three LAN ports. • The BCM50a and BCM50ba have seven LAN ports. • The BCM50e and BCM50be have seven LAN ports. •...
Page 214 Appendix C LAN ports wiring chart The table LAN port wiring on page 214 lists the wiring details for the LAN ports. Table 37 LAN port wiring Signal + Receive Data (Rx+) – Receive Data (Rx–) + Transmit Data (Tx+) No connection No connection –...
Page 215: Wan Ports Wiring Chart
Appendix D WAN ports wiring chart Appendix D WAN ports wiring chart Four BCM50 main units, the BCM50a, BCM50ba, BCM50e, and BCM50be, have a Router card. On a BCM50a and BCM50ba main units, the WAN port is an RJ-11 port. On a BCM50e and BCM50be main units, the WAN port is an RJ-45 port.
Page 216 Appendix D WAN ports wiring chart Table 38 RJ-11 WAN port wiring (Sheet 2 of 2) Signal No connection No connection Table 39 RJ-45 WAN port wiring Signal + Receive Data (Rx+) – Receive Data (Rx–) + Transmit Data (Tx+) No connection No connection –...
Page 217: Expansion Ports Wiring Chart
Appendix E Expansion ports wiring chart Appendix E Expansion ports wiring chart Two of the four RJ-45 connectors on the BCM50, BCM50a, BCM50e, BCM50b, BCM50ba, and BCM50be main units are designated as expansion ports. See the figure Expansion ports on a BCM50 and an expansion unit on page 217.
Page 218 Appendix E Expansion ports wiring chart Table 40 Expansion port wiring (Sheet 2 of 2) Signal – FS256 Receive Data + FS256 Receive Data NN40020-302...
Page 219: Dtm Wiring Chart
Appendix F DTM wiring chart Appendix F DTM wiring chart The digital telephone line connects to the Digital Trunk Module (DTM) through the RJ-48c jack on the front of the media bay module (MBM). See the figure DTM RJ-48C port on page 219.
Page 220 Appendix F DTM wiring chart NN40020-302...
Page 221: Brim Wiring Chart
Appendix G BRIM wiring chart Appendix G BRIM wiring chart The digital BRI ISDN lines connects to the BRIM through the RJ-45 jacks on the front of the media bay module (MBM). See the figure BRIM RJ-45 ports on page 221. You can connect up to four BRI ISDN lines to the BRIM.
Page 222 Appendix G BRIM wiring chart Table 44 BRIM line numbering Default line numbers on Default line numbers on Port number Expansion port 1 Expansion port 2 065–066 095–096 067–068 097–098 069–070 099–100 071–072 101– 02 NN40020-302...
Page 223: Adid Wiring Chart
Appendix H ADID wiring chart Appendix H ADID wiring chart Analog telephone lines connect to the ADID4 or ADID8 through the RJ-21 connector on the front of the media bay module (MBM). See the figure ADID RJ-21 connector on page 223. Figure 94 ADID RJ-21 connector ADID RJ-21 connector...
Page 224 Appendix H ADID wiring chart NN40020-302...
Page 225: Market Profile Attributes
Appendix I Market profile attributes This section describes some of the differences in the market profile attributes. These attributes are derived from the market profile selected when you configure the system. Each market profile uses a set of system attributes that provide specific functionality for the geographical area in which you deploy the system.
Page 226: Digital Interfaces
Appendix I Market profile attributes Table 46 Analog interface availability by market profile Legacy G4x16 ASM/ CTM4/ GATM4/ GATM4/ Legacy G8x16 Market profile ASM8 ASM8+ GASM8 GASI CTM8 GATM8 GATM8 4X16 (new) GATI ADID Australia Bahrain Brazil CALA Canada Caribbean Global Hong Kong Ireland...
Page 227: Tones And Cadences
Appendix I Market profile attributes Table 47 Digital interface availability by market profile (Sheet 2 of 2) Digital DSM16+/ station Market profile DSM32+ interface cNIC DTM R2MFC CALA Canada Caribbean Denmark France Germany Global Holland Hong Kong Ireland Italy Mexico New Zealand North America Norway...
Page 228 Appendix I Market profile attributes • Localized, Dial, and Quiet Dial on page 228 • Special Dial, Overflow, and Busy on page 229 • Ring Back, Aux Ring, Async Ring Back on page 231 • Hold, Warble, Intrusion on page 232 •...
Page 229 Appendix I Market profile attributes Table 48 Localized, Dial, and Quiet Dial (Sheet 2 of 2) Dial Quiet Dial Level per Level per Tone Tones Tone Market profile Localized Tones (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence United Kingdom 440+350 -17.5 Continuous 440+350 -14.5 Continuous...
Page 230 Appendix I Market profile attributes Table 49 Special Dial, Overflow, and Busy (Sheet 2 of 2) Special Dial Overflow Busy Level Level Level Tones Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence New Zealand 400: 0.1 s:0.1 s...
Page 231 Appendix I Market profile attributes Table 50 Ring Back, Aux Ring, Async Ring Back (Sheet 1 of 2) Ring Back Aux Ring Async Ring Back Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence...
Page 232 Appendix I Market profile attributes Table 50 Ring Back, Aux Ring, Async Ring Back (Sheet 2 of 2) Ring Back Aux Ring Async Ring Back Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence...
Page 233 Appendix I Market profile attributes Table 51 Hold, Warble, Intrusion (Sheet 2 of 2) Hold Warble Intrusion Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence Global Cadenced Silence Silence by CoreTel...
Page 234 Appendix I Market profile attributes Table 52 Reorder, 1 kHz (Sheet 2 of 3) Reorder 1 kHz Level Level Tones per Tone Tones per Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence CALA 480+620 250 ms on 1004 Continuous 250 ms off Canada 480+620...
Page 235: Core Parameters For Market Profiles
Appendix I Market profile attributes Table 52 Reorder, 1 kHz (Sheet 3 of 3) Reorder 1 kHz Level Level Tones per Tone Tones per Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence Switzerland -11.5 200 ms on 200 ms off Taiwan 480+620 300 ms on...
Page 236 Appendix I Market profile attributes Table 53 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 2 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Conference tone supported Held line After 30 reminder seconds Delay ring After 15 After 4 rings After 4 rings After 4 rings After 4...
Page 237 Appendix I Market profile attributes Table 53 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 3 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Ringing service mode Ringing service trunk Restriction service mode Restriction Service modes global 131440...
Page 238 Appendix I Market profile attributes Table 53 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 4 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Handsfree Auto Auto Auto Auto Auto Auto Auto Pickup group 1 None None None...
Page 239 Appendix I Market profile attributes Table 54 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 2 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Digital trunking ISDN ISDN ISDN ISDN ISDN ISDN protocols DASS2 DASS2 DASS2...
Page 240 Appendix I Market profile attributes Table 54 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 3 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 241 Appendix I Market profile attributes Table 54 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 4 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Analog VSC None None None None None (tone) ONN blocking Analog VSC None None...
Page 242 Appendix I Market profile attributes Table 55 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 2 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Conference tone supported Held line reminder Off Immediate After 30 seconds Delay ring transfer After 4 rings After 4 rings...
Page 243 Appendix I Market profile attributes Table 55 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 3 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 244 Appendix I Market profile attributes Table 55 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 4 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Analog VSC None None None None 1831 (tone) ONN blocking Analog VSC None None...
Page 245 Appendix I Market profile attributes Table 56 Russia and South Africa parameters (Sheet 2 of 4) Market profile Functionality Attribute Russia South Africa Conference tone supported Held line reminder Off After 30 s Delay ring transfer After 4 rings After 15 rings Transfer callback After 4 rings After 15 rings...
Page 246 Appendix I Market profile attributes Table 56 Russia and South Africa parameters (Sheet 3 of 4) Market profile Functionality Attribute Russia South Africa Ringing service mode Ringing service trunk ans Restriction service mode Restriction global overrides 131440 Restriction filter 01 0, 0(013), Service modes 1(1800, 1866,...
Page 247 Appendix I Market profile attributes Table 56 Russia and South Africa parameters (Sheet 4 of 4) Market profile Functionality Attribute Russia South Africa Analog VSC None 1831 (tone) ONN blocking Analog VSC None 1831 (pulse) BRI VSC None None BRI per loop SuprsBit SuprsBit Release reason...
Page 248 Appendix I Market profile attributes Table 57 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 2 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Conference tone supported Held line Immediate reminder Delay ring After 4 rings After 4 rings After 4 rings After 4 rings...
Page 249 Appendix I Market profile attributes Table 57 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 3 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 250: Analog Trunk Parameters
Appendix I Market profile attributes Table 57 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 4 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Dial tone detection Enabled Enabled Enabled Enabled Enabled Enabled Set preferences Language English EuroSpanish...
Page 251 Appendix I Market profile attributes Table 58 Localization, PSTN standards, and pulse dialing parameters (Sheet 1 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 252 Appendix I Market profile attributes Table 58 Localization, PSTN standards, and pulse dialing parameters (Sheet 2 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 253 Appendix I Market profile attributes Table 58 Localization, PSTN standards, and pulse dialing parameters (Sheet 3 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 254 Appendix I Market profile attributes Table 59 Transmission parameters (Sheet 2 of 2) Transmission Loop length Tx CO gain Rx CO gain PCM coding adjustment (short, medium, (short, medium, Market profile scheme AC impedance capability long) long) Ω Hong Kong mu-law (N/A, 0, N/A) (N/A, 6 dB, N/A)
Page 255 Appendix I Market profile attributes Table 60 Call supervision parameters (Sheet 2 of 2) Call supervision Ring Link/flash time Force on-hook Wetting time confirmation Market profile (ms) OSI time (ms) time (ms) (ms) count (ms) South Africa 1600 Spain 1600 Taiwan 1600 United Kingdom...
Page 256: Gasm8 Parameters
Appendix I Market profile attributes Table 61 On-hook caller ID, disconnect supervision, and message waiting parameters (Sheet 2 of 2) On-hook caller ID Disconnect supervision Message waiting DTMF Market (Start Digit, Line Voltage Stutter profile Stop Digit) Busy tone reversal reversal dial tone New Zealand...
Page 257 Appendix I Market profile attributes • Localization, DIP switch settings, specifications, and transmission parameters on page 257 • Loop interface and call supervision parameters on page 258 • Dial pulse and DTMF parameters on page 258 • MWI, On-hook Caller Id, Disconnect Supervision on page 259 Table 62 Localization, DIP switch settings, specifications, and transmission parameters Specifications...
Page 258 Appendix I Market profile attributes Table 63 Loop interface and call supervision parameters Loop interface Call supervision Disconn Loop Ringing Current Loop Min. Min/max Supervi Ringing amplitu Detect current seize answer recall clear sion OSI frequency Thresho limit duration duration duration duration Time...
Page 259: Gasi Parameters
Appendix I Market profile attributes Table 65 MWI, On-hook Caller Id, Disconnect Supervision On-hook Caller Id Disconnect Supervision High Line Voltage Reversal Class Busy Line Market profile (HV) (LR) Tone FSK support Tone Reversal Australia Supported Supported Yes - AUSTEL Supported 110 V supported...
Page 260 Appendix I Market profile attributes Table 66 GASI parameters (Sheet 1 of 2) Hong North Aspect Parameter Australia CALA Italy Poland Spain UK Canada CaribbeanGlobal Kong America Market Localized? Yes Support (North (North America America n Based n Based A-Law) A-Law) Ω...
Page 261 Appendix I Market profile attributes Table 66 GASI parameters (Sheet 2 of 2) Hong North Aspect Parameter Australia CALA Italy Poland Spain UK Canada CaribbeanGlobal Kong America Dial Pulse Dial Pulse Coding Scheme Minimum/ 40/90 20/90 50/70 48/88 30/70 25/200 25/120 25/120 25/120 25/120 25/120 Maximum...
Page 262: Ata2 Parameters
Appendix I Market profile attributes ATA2 parameters This section contains information for the ATA2 device. The ATA2 is either DR6 or DR7 mode. The mode is determined by the region in which you are located, and is not a modifiable user preference.
Page 263 Appendix I Market profile attributes Table 67 ATA2 DR6 Market Support, Transmission, Loop Interface, Call Supervision, and Dial Pulse parameters (Sheet 2 of 2) Call Supervision Dial Pulse Market Loop Support Transmission Interface Duration (ms) Duration (ms) Dial Ringing Min/ Pulse Min/ Min/...
Page 264: Ata2 Dr7
Appendix I Market profile attributes ATA2 DR7 Table 68 ATA2 DR7 Market Support, Transmission and Loop Interface parameters Market Support Transmission Loop Interface Loop Current Loop Terminal Ringing Ringing Detect Current Market Input Coding Frequency Amplitude Threshold Limit profile Localized? Impedance Scheme (Hz)
Page 265: Voicemail
Appendix I Market profile attributes Table 69 ATA2 DR7 Call Supervision, Dial Pulse, and DTMF parameters Call Supervision Dial Pulse Duration (ms) Duration (ms) DTMF DTMF Dial DTMF Detect Pulse Min/ Min/ Coding Level Market Min/Max Coding Interdigit Scheme profile Seize Answer Recall...
Page 266 Appendix I Market profile attributes Table 70 Voicemail parameters, by country (Sheet 1 of 2) Country Login Alternate Enable Local Maximum National Mailbox Default Touch Number CLID Number Market Mapping Language Tone Gate Length Display Length Argentina Spanish Australia Australian English Austria German...
Page 267 Appendix I Market profile attributes Table 70 Voicemail parameters, by country (Sheet 2 of 2) Country Login Alternate Enable Local Maximum National Mailbox Default Touch Number CLID Number Market Mapping Language Tone Gate Length Display Length Norway Norwegian Pakistan United Kingdom English Panama...
Page 268: Isdn Line Services
Appendix I Market profile attributes ISDN line services The table ISDN line services on page 268 shows the ISDN private network services that are supported by BCM50. The table ISDN services by Protocol on page 268 shows the network-based ISDN supplementary services and the features available for each. Table 71 ISDN line services MCDN over PRI (SL-1) DPNSS...
Page 269 Appendix I Market profile attributes Some of these trunk types are available only when you select specific market profiles. Table 73 Analog and digital trunk types and descriptions (Sheet 1 of 2) Trunk Types Description Digital Carrier Types: T1/E1 Digital line that carries data on 24 channels at 1.544 Mbps (North American); 30 channels at 2048 Mbps (Europe) Loop, E&M, DID and ground start lines are also versions of T1 lines.
Page 270 Appendix I Market profile attributes Table 73 Analog and digital trunk types and descriptions (Sheet 2 of 2) Trunk Types Description Provides H.323 and SIP trunking between BCM and PBX nodes. Analog Trunk Types: Loop start Standard PSTN telephone line. ADID An analog trunk that allows an outside caller to dial directly into a line on the BCM system.
Page 271: 4X16 Wiring Charts
Appendix J 4x16 wiring charts Appendix J 4x16 wiring charts You can connect up to 4 analog telephone lines and up to 16 digital telephones to the 4x16 media bay module (MBM). The analog telephones lines connect to the 4x16 through the RJ-11 jacks (labeled 1 to 4) on the front of the MBM.
Page 272 Appendix J 4x16 wiring charts Table 74 4x16 RJ-11 port wiring (Sheet 2 of 2) Signal No connection No connection Table 75 4x16 default line numbering Default line number on Default line number on Port number Expansion port 1 Expansion port 2 The table 4x16 RJ-21 connector wiring on page 272 lists the wiring details for the RJ-21 connector...
Page 273 Appendix J 4x16 wiring charts Table 76 4x16 RJ-21 connector wiring (Sheet 2 of 2) Default DN on Default DN on Connection Wire color Expansion port 1 Expansion port 2 Red-Slate Ring Slate-Red Black-Blue Ring Blue-Black Black-Orange Ring Orange-Black Black-Green Ring Green-Black Black-Brown...
Page 274 Appendix J 4x16 wiring charts NN40020-302...
Page 275: G4X16 And G8X16 Wiring Charts
Appendix K G4x16 and G8x16 wiring charts Appendix K G4x16 and G8x16 wiring charts You can connect 4 or 8 analog telephone lines and up to 16 digital telephones to the G4x16 or G8x16 media bay module (MBM). The analog telephones lines connect to the G4x16 or G8x16 through the lower RJ-21 (amphenol) connector on the front of the MBM.
Page 276 Appendix K G4x16 and G8x16 wiring charts Table 77 G4x16/G8x16 MBM upper RJ-21 (amphenol) connector wiring for digital telephones (Sheet 2 of 2) Default DN on Default DN on Connection Wire color Expansion port 1 Expansion port 2 White-Green Ring Green-White White-Brown Ring...
Page 277 Appendix K G4x16 and G8x16 wiring charts Table 78 G4x16 and G8x16 lower RJ-21 (amphenol) connector wiring for analog PSTN lines (Sheet 1 of 2) Default line numbers on Default line numbers on Line Connection Wire color Expansion port 1 Expansion port 2 White-Blue Ring...
Page 278 Appendix K G4x16 and G8x16 wiring charts Table 78 G4x16 and G8x16 lower RJ-21 (amphenol) connector wiring for analog PSTN lines (Sheet 2 of 2) Default line numbers on Default line numbers on Line Connection Wire color Expansion port 1 Expansion port 2 Violet-Slate —...
Page 279: Dsm16 And Dsm32 Wiring Charts
Appendix L DSM16 and DSM32 wiring charts Appendix L DSM16 and DSM32 wiring charts Digital telephones, such as the Business Series Telephones, connect to the Digital Station Module (DSM16 or DSM32) through the RJ-21 connectors on the front of the media bay module. The DSM16 has a single RJ-21 connector and the DSM32 has two RJ-21 connectors.
Page 280 Appendix L DSM16 and DSM32 wiring charts Table 79 DSM16 and DSM32 RJ-21 connector wiring (Sheet 2 of 3) Default DN on Expansion Default DN on Expansion port 1 port 2 Connection Wire color White-Brown Ring Brown-White White-Slate Ring Slate-White Red-Blue Ring Blue-Red...
Page 281 Appendix L DSM16 and DSM32 wiring charts Table 79 DSM16 and DSM32 RJ-21 connector wiring (Sheet 3 of 3) Default DN on Expansion Default DN on Expansion port 1 port 2 Connection Wire color Violet-Slate connection — — — — —...
Page 282 Appendix L DSM16 and DSM32 wiring charts NN40020-302...
Page 283: Asm8, Asm8+, And Gasm Wiring Chart
Appendix M ASM8, ASM8+, and GASM wiring chart Appendix M ASM8, ASM8+, and GASM wiring chart Analog telephony devices, such as single line telephones, modems and Fax machines, connect to the Analog Station Module (ASM) through the RJ-21 connector on the front of the media bay module.
Page 284 Appendix M ASM8, ASM8+, and GASM wiring chart Table 80 ASM RJ-21 connector wiring (Sheet 2 of 2) Default DN on Default DN on Connection Wire color Expansion port 1 Expansion port 2 No connection Red-Brown — — — No connection Brown-Red No connection Violet-Slate...
Page 285: Market Profile Attributes
Appendix N Market profile attributes This section describes some of the differences in the market profile attributes. These attributes are derived from the market profile selected when you configure the system. Each market profile uses a set of system attributes that provide specific functionality for the geographical area in which you deploy the system.
Page 286: Digital Interfaces
Appendix N Market profile attributes Table 81 Analog interface availability by market profile Legacy G4x16 ASM/ CTM4/ GATM4/ GATM4/ Legacy G8x16 Market profile ASM8 ASM8+ GASM8 GASI CTM8 GATM8 GATM8 4X16 (new) GATI ADID Australia Bahrain Brazil CALA Canada Caribbean Global Hong Kong Ireland...
Page 287: Tones And Cadences
Appendix N Market profile attributes Table 82 Digital interface availability by market profile (Sheet 2 of 2) Digital DSM16+/ station Market profile DSM32+ interface cNIC DTM R2MFC CALA Canada Caribbean Denmark France Germany Global Holland Hong Kong Ireland Italy Mexico New Zealand North America Norway...
Page 288 Appendix N Market profile attributes • Localized, Dial, and Quiet Dial on page 288 • Special Dial, Overflow, and Busy on page 289 • Ring Back, Aux Ring, Async Ring Back on page 291 • Hold, Warble, Intrusion on page 292 •...
Page 289 Appendix N Market profile attributes Table 83 Localized, Dial, and Quiet Dial (Sheet 2 of 2) Dial Quiet Dial Level per Level per Tone Tones Tone Market profile Localized Tones (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence United Kingdom 440+350 -17.5 Continuous 440+350 -14.5 Continuous...
Page 290 Appendix N Market profile attributes Table 84 Special Dial, Overflow, and Busy (Sheet 2 of 2) Special Dial Overflow Busy Level Level Level Tones Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence New Zealand 400: 0.1 s:0.1 s...
Page 291 Appendix N Market profile attributes Table 85 Ring Back, Aux Ring, Async Ring Back (Sheet 1 of 2) Ring Back Aux Ring Async Ring Back Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence...
Page 292 Appendix N Market profile attributes Table 85 Ring Back, Aux Ring, Async Ring Back (Sheet 2 of 2) Ring Back Aux Ring Async Ring Back Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence...
Page 293 Appendix N Market profile attributes Table 86 Hold, Warble, Intrusion (Sheet 2 of 2) Hold Warble Intrusion Level Level Level Tones per Tone Tones Tone Tones Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence Global Cadenced Silence Silence by CoreTel...
Page 294 Appendix N Market profile attributes Table 87 Reorder, 1 kHz (Sheet 2 of 3) Reorder 1 kHz Level Level Tones per Tone Tones per Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence CALA 480+620 250 ms on 1004 Continuous 250 ms off Canada 480+620...
Page 295: Core Parameters For Market Profiles
Appendix N Market profile attributes Table 87 Reorder, 1 kHz (Sheet 3 of 3) Reorder 1 kHz Level Level Tones per Tone Tones per Tone Market profile (Hz) (dBm0) Cadence (Hz) (dBm0) Cadence Switzerland -11.5 200 ms on 200 ms off Taiwan 480+620 300 ms on...
Page 296 Appendix N Market profile attributes Table 88 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 2 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Conference tone supported Held line After 30 reminder seconds Delay ring After 15 After 4 rings After 4 rings After 4 rings After 4...
Page 297 Appendix N Market profile attributes Table 88 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 3 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Ringing service mode Ringing service trunk Restriction service mode Restriction Service modes global 131440...
Page 298 Appendix N Market profile attributes Table 88 Australia, Brazil, CALA, Canada, Caribbean, and Denmark parameters (Sheet 4 of 4) Market profile Functionality Attribute Australia Bahrain Brazil CALA Canada Caribbean Denmark Handsfree Auto Auto Auto Auto Auto Auto Auto Pickup group 1 None None None...
Page 299 Appendix N Market profile attributes Table 89 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 2 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Digital trunking ISDN ISDN ISDN ISDN ISDN ISDN protocols DASS2 DASS2 DASS2...
Page 300 Appendix N Market profile attributes Table 89 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 3 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 301 Appendix N Market profile attributes Table 89 France, Germany, Global, Holland, Hong Kong, and Ireland parameters (Sheet 4 of 4) Market profile Hong Functionality Attribute France Germany Global Holland Kong Ireland Analog VSC None None None None None (tone) ONN blocking Analog VSC None None...
Page 302: Nn40020
Appendix N Market profile attributes Table 90 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 2 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Conference tone supported Held line reminder Off Immediate After 30 seconds Delay ring transfer After 4 rings After 4 rings...
Page 303 Appendix N Market profile attributes Table 90 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 3 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 304 Appendix N Market profile attributes Table 90 Italy, Mexico, New Zealand, North America, Norway, and Poland (Sheet 4 of 4) Market profile North Functionality Attribute Italy Mexico Zealand America Norway Poland Analog VSC None None None None 1831 (tone) ONN blocking Analog VSC None None...
Page 305 Appendix N Market profile attributes Table 91 Russia and South Africa parameters (Sheet 2 of 4) Market profile Functionality Attribute Russia South Africa Conference tone supported Held line reminder Off After 30 s Delay ring transfer After 4 rings After 15 rings Transfer callback After 4 rings After 15 rings...
Page 306 Appendix N Market profile attributes Table 91 Russia and South Africa parameters (Sheet 3 of 4) Market profile Functionality Attribute Russia South Africa Ringing service mode Ringing service trunk ans Restriction service mode Restriction global overrides 131440 Restriction filter 01 0, 0(013), Service modes 1(1800, 1866,...
Page 307 Appendix N Market profile attributes Table 91 Russia and South Africa parameters (Sheet 4 of 4) Market profile Functionality Attribute Russia South Africa Analog VSC None 1831 (tone) ONN blocking Analog VSC None 1831 (pulse) BRI VSC None None BRI per loop SuprsBit SuprsBit Release reason...
Page 308 Appendix N Market profile attributes Table 92 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 2 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Conference tone supported Held line Immediate reminder Delay ring After 4 rings After 4 rings After 4 rings After 4 rings...
Page 309 Appendix N Market profile attributes Table 92 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 3 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Ringing service Manual Manual Manual mode Ringing service trunk ans Restriction service mode Restriction global...
Page 310: Analog Trunk Parameters
Appendix N Market profile attributes Table 92 PRC, Spain, Sweden, Switzerland, Taiwan, and United Kingdom parameters (Sheet 4 of 4) Market profile United Functionality Attribute Spain Sweden Switzerland Taiwan Kingdom Dial tone detection Enabled Enabled Enabled Enabled Enabled Enabled Set preferences Language English EuroSpanish...
Page 311 Appendix N Market profile attributes Table 93 Localization, PSTN standards, and pulse dialing parameters (Sheet 1 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 312 Appendix N Market profile attributes Table 93 Localization, PSTN standards, and pulse dialing parameters (Sheet 2 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 313 Appendix N Market profile attributes Table 93 Localization, PSTN standards, and pulse dialing parameters (Sheet 3 of 3) Differences PSTN Standards, Specifications between GATI, Referenced Pulse Dialing (ms) G4x16/G8x16, New GATM4/8, and Break Make Interdigit Market profile Localized Legacy GATM4/8 time time time...
Page 314 Appendix N Market profile attributes Table 94 Transmission parameters (Sheet 2 of 2) Transmission Loop length Tx CO gain Rx CO gain PCM coding adjustment (short, medium, (short, medium, Market profile scheme AC impedance capability long) long) Ω Hong Kong mu-law (N/A, 0, N/A) (N/A, 6 dB, N/A)
Page 315 Appendix N Market profile attributes Table 95 Call supervision parameters (Sheet 2 of 2) Call supervision Ring Link/flash time Force on-hook Wetting time confirmation Market profile (ms) OSI time (ms) time (ms) (ms) count (ms) South Africa 1600 Spain 1600 Taiwan 1600 United Kingdom...
Page 316: Gasm8 Parameters
Appendix N Market profile attributes Table 96 On-hook caller ID, disconnect supervision, and message waiting parameters (Sheet 2 of 2) On-hook caller ID Disconnect supervision Message waiting DTMF Market (Start Digit, Line Voltage Stutter profile Stop Digit) Busy tone reversal reversal dial tone New Zealand...
Page 317 Appendix N Market profile attributes • Localization, DIP switch settings, specifications, and transmission parameters on page 317 • Loop interface and call supervision parameters on page 318 • Dial pulse and DTMF parameters on page 318 • MWI, On-hook Caller Id, Disconnect Supervision on page 319 Table 97 Localization, DIP switch settings, specifications, and transmission parameters Specifications...
Page 318 Appendix N Market profile attributes Table 98 Loop interface and call supervision parameters Loop interface Call supervision Disconn Loop Ringing Current Loop Min. Min/max Supervi Ringing amplitu Detect current seize answer recall clear sion OSI frequency Thresho limit duration duration duration duration Time...
Page 319: Gasi Parameters
Appendix N Market profile attributes Table 100 MWI, On-hook Caller Id, Disconnect Supervision On-hook Caller Id Disconnect Supervision High Line Voltage Reversal Class Busy Line Market profile (HV) (LR) Tone FSK support Tone Reversal Australia Supported Supported Yes - AUSTEL Supported 110 V supported...
Page 320 Appendix N Market profile attributes Table 101 GASI parameters (Sheet 1 of 2) Hong North Aspect Parameter Australia CALA Italy Poland Spain UK Canada CaribbeanGlobal Kong America Market Localized? Yes Support (North (North America America n Based n Based A-Law) A-Law) Ω...
Page 321 Appendix N Market profile attributes Table 101 GASI parameters (Sheet 2 of 2) Hong North Aspect Parameter Australia CALA Italy Poland Spain UK Canada CaribbeanGlobal Kong America Dial Pulse Dial Pulse Coding Scheme Minimum/ 40/90 20/90 50/70 48/88 30/70 25/200 25/120 25/120 25/120 25/120 25/120 Maximum...
Page 322: Ata2 Parameters
Appendix N Market profile attributes ATA2 parameters This section contains information for the ATA2 device. The ATA2 is either DR6 or DR7 mode. The mode is determined by the region in which you are located, and is not a modifiable user preference.
Page 323 Appendix N Market profile attributes Table 102 ATA2 DR6 Market Support, Transmission, Loop Interface, Call Supervision, and Dial Pulse parameters (Sheet 2 of 2) Call Supervision Dial Pulse Market Loop Support Transmission Interface Duration (ms) Duration (ms) Dial Ringing Min/ Pulse Min/ Min/...
Page 324: Ata2 Dr7
Appendix N Market profile attributes ATA2 DR7 Table 103 ATA2 DR7 Market Support, Transmission and Loop Interface parameters Market Support Transmission Loop Interface Loop Current Loop Terminal Ringing Ringing Detect Current Market Input Coding Frequency Amplitude Threshold Limit profile Localized? Impedance Scheme (Hz)
Page 325: Voicemail
Appendix N Market profile attributes Table 104 ATA2 DR7 Call Supervision, Dial Pulse, and DTMF parameters Call Supervision Dial Pulse Duration (ms) Duration (ms) DTMF DTMF Dial DTMF Detect Pulse Min/ Min/ Coding Level Market Min/Max Coding Interdigit Scheme profile Seize Answer Recall...
Page 326 Appendix N Market profile attributes Table 105 Voicemail parameters, by country (Sheet 1 of 2) Country Login Alternate Enable Local Maximum National Mailbox Default Touch Number CLID Number Market Mapping Language Tone Gate Length Display Length Argentina Spanish Australia Australian English Austria German...
Page 327 Appendix N Market profile attributes Table 105 Voicemail parameters, by country (Sheet 2 of 2) Country Login Alternate Enable Local Maximum National Mailbox Default Touch Number CLID Number Market Mapping Language Tone Gate Length Display Length Norway Norwegian Pakistan United Kingdom English Panama...
Page 328: Isdn Line Services
Appendix N Market profile attributes ISDN line services The table ISDN line services on page 328 shows the ISDN private network services that are supported by BCM50. The table ISDN services by Protocol on page 328 shows the network-based ISDN supplementary services and the features available for each. Table 106 ISDN line services MCDN over PRI (SL-1) DPNSS...
Page 329 Appendix N Market profile attributes Some of these trunk types are available only when you select specific market profiles. Table 108 Analog and digital trunk types and descriptions (Sheet 1 of 2) Trunk Types Description Digital Carrier Types: T1/E1 Digital line that carries data on 24 channels at 1.544 Mbps (North American); 30 channels at 2048 Mbps (Europe) Loop, E&M, DID and ground start lines are also versions of T1 lines.
Page 330 Appendix N Market profile attributes Table 108 Analog and digital trunk types and descriptions (Sheet 2 of 2) Trunk Types Description Provides H.323 and SIP trunking between BCM and PBX nodes. Analog Trunk Types: Loop start Standard PSTN telephone line. ADID An analog trunk that allows an outside caller to dial directly into a line on the BCM system.
Page 331: Index
Index Numerics 4x16 BCM50 default DNs 272 ASM (analog station module) 49 default line numbers 272 DSM 16 and DSM 32 (digital station module) 48 hardware description 48, 49 DTM (digital trunk module) 45 wiring chart 271, 275 field replaceable units 59 installation prerequisites 77 installing 73 accessories...
Page 332 Index digital lines, 4x16 47, 48 external equipment, safety warning 42, 58 digital station media bay module 47 external line isolation units (LIU), MSC jacks 42, 58 digital telephone external paging 4x16 module 48, 49 amplifier 58 DSM 16 and DSM 32 modules 48 DTM module 45 digital trunk module registration 25...
Page 333 25 default on BRIM 222 networking line numbers WAN card 59 default on 4x16 272 Nortel distributor 35 default on ADID4 223 North American components 48 default on DTM 219 default on GATM 275 default on main unit 207...
Page 334 175 express routing code 35 how to get help 34 DTM module 45 Nortel reseller 35 line types 268, 328 Nortel Solutions Center 34 Nortel Web site 34 Switches, setting MBM 96 radio-frequency interference 25 symbols 31 regions system defaults, by region 235, 295...
Page 335 Index ADID8 223 ASM 283 BRIM 221 DSM16 279 DSM32 279 DTM 219 expansion port 217 expansion unit 217 LAN port 213 main unit 215, 217 WAN port 215 wiring field card (WFC) 90 wiring requirements 78 Installation and Maintenance Guide...

This manual is also suitable for:

Bcm 50 3.0

Nortel BCM50 3.0 Installation And Maintenance Manual

New in this Release

Regulatory Information

Chapter 1 Getting Started

Chapter 2 Introducing the BCM50 Hardware

Chapter 3 Viewing the BCM50 System Leds

Chapter 4 Determining DHCP Server Configuration and IP Address

Chapter 5

Installing the BCM50 System

Chapter 6 Checking the Installation Prerequisites

Chapter 7 Installing the Main Unit

Chapter 8 Installing an Expansion Unit

Chapter 9 Connecting the Cables to the BCM50 System

Chapter 10 Installing Telephones and Peripherals

Chapter 11 Installing the Analog Terminal Adapter

Chapter 12 Configuring the BCM50 System

Chapter 13 Using Telset Administration to Set the Basic Parameters

Chapter 14 Using Element Manager to Set the Basic Parameters

Chapter 15 Using the Startup Profile to Configure Parameters

Chapter 16 Completing the Initial Installation (Optional)

Chapter 17 Connecting the BCM50 System to the LAN and WAN

Chapter 18 Testing Basic BCM50 Functionality

Chapter 19 Replacing the BCM50 System Components

Chapter 20 Replacing a Power Supply

Chapter 21 Replacing a Main Unit

Chapter 22

Replacing a Media Bay Module

Chapter 23 Replacing an Expansion Unit

Replacing an Internal Component

Chapter 24 Replacing an Internal Component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193

RJ-21 Telephony Connector Wiring Chart

BRI Wiring Chart

LAN Ports Wiring Chart

WAN Ports Wiring Chart

Expansion Ports Wiring Chart

DTM Wiring Chart

BRIM Wiring Chart

ADID Wiring Chart

Market Profile Attributes

Appendix I

Appendix H

Appendix G

Appendix F

Appendix E

Quick Links

Related Manuals for Nortel BCM50 3.0

Summary of Contents for Nortel BCM50 3.0