Bosch Solution 64 Installer's Manual page 69

Press [MENU] + [5] + [3] + [0]. The keypad will display the
1)
current Call Back telephone number if programmed.
Call Back Number N001
Press 0-9 OK to SAVE
Using the numeric keys, enter all the digits of the Call Back
2)
number. You can change a single digit by scrolling the cursor
left or right. For special characters including, pause, * or #, use
the up and down arrow keys.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
i
You must add any area codes or other special access numbers
which are required to be able to dial the remote computer from
the panel phone line. Simply add these numbers before the Call
Note
Back number.
Comms > Remote Access >
RAS Security PIN
The RAS security PIN programmed here must match
the security PIN programmed in the customer file of the
SolutionLink RAS upload/download database otherwise a
connection to the panel cannot be established.
1) Press [MENU] + [5] + [3] + [1]. The keypad will display the
current RAS Security PIN. The default = 12345678.
RAS Security PIN
12345678
Press 0-9 OK to SAVE
2) Using the numeric keys, enter all the digits of the new RAS
security PIN. You can change a single digit by scrolling the
cursor left or right.
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
Comms > Remote Access >
Log Threshold
The control panel can store up to 256 system events in its
built in history log. A newly installed panel will have 100% of
its log space available for new events (0% full). As the panel
starts to store events in the log, the capacity for new events is
reduced. The history log is 100% full when event 256 is stored
in memory. Event 257 will start to overwrite the oldest events
in the log.
When the Log Threshold option is programmed, the panel
will send a 'Log Threshold' report to the base station when
the event log reaches the percentage as set since the last
SolutionLink session.
Bosch Security Systems | 11/05 | BLCC110I
MENU 5-3-1

1 2 3 4 5 6 7
MENU 5-3-2

7 0
If the event log reaches 100% capacity before a SolutionLink
RAS session is established then the system will send a 'Log
Overflow' report. The panel will also log these events in its
memory.
1) Press [MENU] + [5] + [3] + [2]. The keypad will display the
current threshold limit. The default is 70% full.
Log Threshold N001
070 %
Press 0-9 OK to SAVE
2) Using the numeric keys enter the new threshold limit, then
press [OK] to save and exit or press [MENU] to exit without
saving. There is no need to enter the % symbol.
i
Each time a SolutionLink RAS session is established with the
panel, the log information will be uploaded to the SolutionLink
database where it can be reported on or archived for later use
Note
Comms > Remote Access >
Ring Count
0 = No Answer
8
1 to 15 = Answer Ring Count
This menu sets the number of rings the panel will wait until
answering an incoming call. Programming a zero will stop the
panel from answering any incoming calls.
1) Press [MENU] + [5] + [3] + [3]. The keypad will display the
current ring count.
Ring Count N001
10-10 Rings
Press 0-9 OK to SAVE
2) Use the up and down arrow keys to select the required ring
count then Press [OK] to save and exit or press [MENU] to exit
without saving.
i
If answering machine bypass is required to allow a SolutionLink
connection to be made without the answering machine
answering the call, see MENU 5-3-4 — SolutionLink RAS Options
Note
Comms > Remote Access >
SolutionLink
Options
%
1 RAS Allowed
2 Call Back Verification Required
3 Terminate RAS on Alarm
4 Answer Bypass
5 Answer Incoming Call Only If Armed
6 Remote Program Editing Only When Disarmed
7 Allow User Functions Via Remote Access Software
8 Report / Log RAS Start / End Sessions
1) Press [MENU] + [5] + [3] + [4]. The keypad will display the
current RAS options.
Solution 64 | Installer Guide | Comms Programming

RAS

MENU 5-3-3
10
MENU 5-3-4
Y
N
Y
Y
N
N
Y
Y
9-7