User Rf Keyfobs - Bosch Solution 64 Installer's Manual

Solution 64 | Installer Guide | Access Programming
To add token for Ur001
John Smith
Swipe New Token
Press OK or MENU OK or MENU
i
If the Add Token command is initiated from a keypad that
does not have a built in reader, you will need to select a reader
from the list before proceeding. Swipe the Token at the selected
Note
reader.
Access > Token >
Delete Token
This command allows the Installer or Master User to delete
Token IDs which have been programmed into the system.
1) Enter [MENU] + [1] + [2] + [1] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that have Tokens assigned to them.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name
Press  OK or MENU
2) Press [OK] to delete the token or press [MENU] to exit without
saving.
To delete token for Ur001
John Smith press OK
Press OK or MENU OK or MENU
Access > Token >
Token Status
This command allows the Installer or Master User to identify
who a Token has been assigned to. You will need to have
the token in order to do the test. This command can only be
performed at a prox keypad.
Enter [MENU] + [1] + [2] + [2]. The system will prompt you to
1)
swipe the token to be checked.
Swipe token to be
identified
Press OK or MENU OK or MENU
2) Present the token to the keypad, you will hear a confirmation
beep and the display will show the token status.
Token belongs to Ur002
Debbie Smith
Press OK or MENU OK or MENU
3) To exit, press [OK] or [MENU].
5-4
-
MENU 1-2-1
 
-
MENU 1-2-2
 
Us er R F K eyfob s
This section outlines how to add and delete RF keyfobs. RF
Keyfobs provide an alternate method for users to turn the
system on and off.
There are two methods for adding RF Keyfobs, Direct Entry
and Learn Mode. The system will prompt for the appropriate
method depending on the Receiver type fitted to the system.
The RF Keyfob must be compatible with the RF Receiver that
has been programmed in MENU 3-5-0 — Input Type.
Refer to MENU 6-2-2 — RF Device Options to configure the
following preferences for RF Keyfobs.
Audible RF Keyfob Panic,

Report RF Keyfob Panic and

RF Keyfob 'Part On' Arming Allowed.

RF Keyfobs will follow all user settings.
Access > RF Keyfob >
Add Keyfob
This menu allows the Installer or a Master User to assign an RF
Keyfob to a user. All users can have an RF Keyfob assigned if
required.
Keyfob Direct Entry Mode
1) Enter [MENU] + [1] + [3] + [0] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that dont already have an RF Keyfob assigned.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 User 3 Name
Press  OK or MENU
2) Enter the RF Keyfob ID Number.
Enter Keyfob RFid for
Ur002 Debbie Smith
009553507
Press OK or MENU OK or MENU
3) Press [OK] to save and exit or press [MENU] to exit without
saving.
Access > RF Keyfob >
Delete Keyfob
This command allows the Installer or a Master User to delete an
RF Keyfob ID that has been assigned to a user.
1) Enter [MENU] + [1] + [3] + [1] and use the up and down arrows
to highlight the user in the list then press [OK]. The system will
only list users that have an RF Keyfob assigned.
Ur001 John Smith
Ur002 Debbie Smith
Ur003 Mary Smith
Press  OK or MENU
-
MENU 1-3-0
 
-
MENU 1-3-1
 
Bosch Security Systems | 11/05 | BLCC110I