Area Reporting; Fire Alarm - Bosch Solution 64 Installer's Manual

Report Exit Error
This option allows the system to report and Exit Error Alarm.
An exit error occurs when an entry/exit delay zone becomes unsealled
during exit delay time and remains unsealled at the end of exit delay
time. If this happens, the entry delay will start. If the area is not
turned off (disarmed) before the entry delay time expires an Exit Error
alarm report will be sent.
Smart Lockout
Smart lockout allows and previously locked zones to reactivate during
the siren run time when a new alarm event occurs.
Cancel Reports
When set, a Cancel report will be sent if a user disarms the area before
the siren timer expires.
Open/Close Reports For Part On
When set, the panel will Send Open or Close reports when the system
is armed in Part On mode.
Open/Close Reports Only After Alarm
When set, the panel will send a single Open / Close report if a
previous alarm has occured. This report will be sent for all users
regardless of whether or not they have been programmed to send
Open/Close reports.
Areas > Properties >
Strobe Trigger
1 Audible Burglary Alarm
2 Silent Burglary Alarm
3

Fire Alarm

4 Arm / Disarm Flash Via RF Keyfob
5 Arm / Disarm Flash Via Keyswitch or PGM Input
6 Reserved
7 24-Hour Alarm
8 Reserved
Programming any of these options allow the strobe output to
operate when the corresponding event occurs. The strobe light
must be connected to an output programmed as a Event Type
48 for it to operate. See Section 9 — output Programming for
more Information on output event types.
Enter [MENU] + [2] + [1] + [5] and select the area from the list
1)
then press [OK].
2) Use the up and down arrow keys to highlight the option then
press the [ON] key to enable or the [OFF] key to disable.
 Audible Burglary Alarm
Silent Burglary Alarm
 Fire Alarm
Press  OK ON OFF MENU
3) Repeat Step 2 until all options are programmed as required,
then press [OK] to save and exit or press [MENU] to exit
without saving.
Audible Burglary Alarm
When selected, the panel will activate the strobe output when an
audible burglary zone has triggered an alarm.
Bosch Security Systems | 11/05 | BLCC110I
Silent Burglary Alarm
When selected, the panel will activate the strobe output when a silent
burglary zone has triggered an alarm.
Fire Alarm
When selected, the panel will activate the strobe output when a zone
programmed as fire (audible or silent) has triggered an alarm.
Arm/Disarm Flash Via RF Keyfob
When slected, the panel will activate the strobe output for six seconds
when a user turns the area on via an RF Key fob. This provides silent
feedback to the user that the signal has been received.
Arm/Disarm Flash Via Keyswitch or PGM Input
When selected, the panel will activate the strobe output for six
seconds when a user turns the area on via a Keyswitch Input or the
Programmable Input. This provides silent feedback to the user that
the signal has been received.
24-Hour Alarm
When selected, the panel will activate the strobe output when a zone
programmed as 24-hour (audible or silent) has registered an alarm.
Zones programmed as 24-Hour Hold-Up are not included.
A rea R epo rting
Areas > Reporting >
MENU 2-1-5

Account Dest 1
Y
N
The area account number identifies which control panel is
Y
reporting to the security company's base station receiver. Each
N
destination can have a different account number programmed.
N
The number should be entered from left to right with trailing
N
zeros.
Y
1)
N
2)
3)
Areas > Reporting >
Account Dest 2
The area account number identifies which control panel is
reporting to the security company's base station receiver. Each
destination can have a different account number programmed.
The number should be entered from left to right with trailing
zeros.
1)
Solution 64 | Installer Guide | Area Programming
0 0
Enter [MENU] + [2] + [2] + [0] and select the area from the list
then press [OK].
Using the numeric keys, enter the new account number. Use
the up and down arrows to select special characters BCDEF.
Account Dest 1 A001
1604000000
Press  0-9 OK to SAVE
Press [OK] to save and exit or press [MENU] to exit without
saving.
0 0
Enter [MENU] + [2] + [2] + [1] and select the area from the list
then press [OK].
MENU 2-2-0

0 0 0 0 0 0 0
MENU 2-2-1
0 0 0 0 0 0 0
0
0
6-5