1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Control Panel
  5. Solution 6+6 Wireless On/Off
  6. Quick reference manual

Bosch Solution 6+6 Quick Reference Manual

Hide thumbs Also See for Solution 6+6:
Table of Contents

Advertisement

Quick Links

Download this manual
Solution 6+6
Quick Reference Guide
ISSUE 1.20

Advertisement

Table of Contents
loading

Related Manuals for Bosch Solution 6+6

Summary of Contents for Bosch Solution 6+6

  • Page 1 Solution 6+6 Quick Reference Guide ISSUE 1.20...
  • Page 2 Notice of Liability While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty Limited nor any of its official representatives shall have any liability to any person or entity with respect to any liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this book.
  • Page 3 Hand Held Programmer (CC814) Programming Key (CC810) Alarm Link (Upload/Download) Software (CC816) Note: For further information on the different programming options available for the Solution 6+6, refer to the Installation Manual (MA600I). Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...
  • Page 4 Two beeps will be heard and the system will return to the disarmed state. For a more detailed explanation, refer to the Installation Manual Solution 6+6 (MA600I). SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...

  • Page 5: Quick Start

    The example given in this quick reference guide is a simplified description of how to configure the panel. This system offers many other programmable features, which are described in detail in the Installation Manual (MA600I). Solution 6+6 Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 6: Installer's Programming Commands

    How To Set the Number Of Days Until The First Test Report Enter your followed by and the button. Enter the (01 – 99) until the first test report followed by the button. SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...
  • Page 7 Two beeps will be heard and the codepad will cease beeping once every two seconds. How To Send A Test Report Enter your followed by and the button. Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 8: Master Code Functions

    After the last digit of the second telephone number has been entered, press the button to separate the second telephone number and the third telephone number, otherwise, press the button to exit this function. SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...
  • Page 9 Three beeps indicate that day alarm is turned on, two beeps indicate that day alarm is turned off. How To Reset Latching Outputs Enter your followed by and the button. How To Initiate A Modem Call Enter your followed by and the button. Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 10: User Code Functions

    Strobe Test Turning Day Alarm On and Off Fault Analysis Mode Initiate Modem Call Reset Latching Outputs Codepad ID Beeper Tone Change Initiate Test Report Table 9: Hold Down Functions SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...
  • Page 11 3 = 2K2 7 = 5K6 11 = 22K 15 = Split EOL (3K3/6K8) For 4 = 3K3 8 = 6K8 12 = Reserved 6 Zones + 6 Tamper Zones Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 12: Zone Types

    90 Seconds 10 Seconds 120 Seconds 15 Seconds 200 Seconds Zone Descriptions Use this table as a reference to indicate what each zone is connected to. Zone Description Tamper Description Zone SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...
  • Page 13 Location 217 Increments Of 16 Seconds (0 - 240 Sec’s) Location 218 - 219 Sensor Watch Time Location 218 Increments Of Days (Tens Digit) Location 219 Increments Of Days (Units Digit) Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 14: Codepad Lockout Time

    8 = Delay Siren Until Transmission Complete Location 226 System Options 1 1 = Enable Forced Arming 2 = Enable BOSCH Smart Lockout 4 = Enable Monitoring Of Horn Speaker 8 = Enable Horn Speaker Beeps For Remote Control Operation Location 227...

  • Page 15: Disable Factory Default

    Wiring Diagram For Keyswitch Zone Figure 2: Wiring Diagram For Keyswitch Zone Wiring Diagram For Keyswitch Zone When System Has Been Partitioned Figure 3: Wiring Diagram For Keyswitch Zone When Partitioned Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

  • Page 16: Wiring Diagram

    Page 16 Quick Reference Guide Solution 6+6 Wiring Diagram Figure 4: Wiring Diagram SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...

  • Page 17: Component Overlay

    Quick Reference Guide Page 17 Solution 6+6 Component Overlay Figure 5: Component Overlay Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...
  • Page 18 If the “Area Addressable” codepad is assigned to Area 2 DIP Switch 2 on the back of the remote codepad will need to be in the “ON” position. The following locations for Output 1 will need to be programmed. [LOCATION 186 = 6, 187 = 1] SOL 6+6 QUICK REF GUIDE.DOC Bosch Security Systems Pty Limited...
  • Page 19 DIP Switch 2 on the back of the remote codepad will need to be in the “ON” position. The following locations for Output 1 will also need to be programmed. [LOCATION 186 = 6, LOCATION 187 = 1] Bosch Security Systems Pty Limited SOL 6+6 QUICK REF GUIDE.DOC...

Table of Contents