Honeywell ADEMCO MX8000 Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Receiver
  5. MX8000
  6. Installation and operation manual

Honeywell ADEMCO MX8000 Installation And Operation Manual

Digital alarm receiver
Hide thumbs Also See for ADEMCO MX8000:
Table of Contents

Advertisement

Quick Links

Download this manual
K5982V2 11/06 Rev. A
ADEMCO MX8000
ADEMCO MX8000
ADEMCO MX8000
ADEMCO MX8000
Digital Alarm Receiver
Digital Alarm Receiver
Digital Alarm Receiver
Digital Alarm Receiver
Installation and Operation Guide

Advertisement

Table of Contents
loading

Related Manuals for Honeywell ADEMCO MX8000

Summary of Contents for Honeywell ADEMCO MX8000

  • Page 1 ADEMCO MX8000 ADEMCO MX8000 ADEMCO MX8000 ADEMCO MX8000 Digital Alarm Receiver Digital Alarm Receiver Digital Alarm Receiver Digital Alarm Receiver Installation and Operation Guide K5982V2 11/06 Rev. A...

  • Page 2: Table Of Contents

    Section 1 System Overview .............................1–1 Features ................................1–1 Optional Accessories ............................1–1 Formats Compatible with the MX8000 ......................1–2 MX8000 Supported SIA Digital I-III Levels .......................1–3 How to Use this Manual ............................1–3 Terminology ................................1–4 What’s in the Box ..............................1–4 General Recommendations, Notes, and Limitations ..................1–5...
  • Page 3 ................................5–26 5.4.7 Virtual Receiver/Line Numbers ........................5–27 Line Device Menu ..............................5–28 5.5.1 Add Line Device ..............................5–38 5.5.2 Edit Line – MX8000–LC3 (3 Line) ........................5–38 5.5.3 Edit Line – MX8000–LRR ..........................5–53 5.5.4 Edit Line – MX8000–LC1 (1 Line) ........................5–56 5.5.5 Copy Device(s) ..............................5–68...
  • Page 4 Good Data with Bad Data ..........................8–27 8.8.6 Validation Byte (V-Byte) ............................8–27 8.8.7 System Messages ..............................8–28 8.8.8 Communication from a Computer to the MX8000 ..................8–28 ITI Generic Computer Format ..........................8–29 8.9.1 Convention Used In This Section ........................8–29 8.9.2 Report Record ..............................8–29 8.9.3...
  • Page 5 Table 5–9: System Options ...............................5–22 Table 5–10: 685, CAPS, and CP-220 1–9/A–Z Entries ....................5–23 Table 5–11: Line Device Menu Options ...........................5–29 Table 5–12: MX8000–LC3 Edit Line List Items and Description ..................5–39 Table 5–13: Valid Programmable String Characters .....................5–44 Table 5–14: Account Characters ............................5–45 Table 5–15: Hexadecimal AlarmNet Number to Decimal Conversion...
  • Page 6 Table 8–22: Delete a Listen-in Account Request Components ...................8–12 Table 8–23: Contact ID Event Definition Codes ......................8–15 Table 8–24: MX8000/685 System Messages .........................8–21 Table 8–25: MX8000/CP-220 System Messages ......................8–24 Table 8–26: Data String Description ..........................8–25 Table 8–27: Special Characters Used in the Protocol ....................8–25...
  • Page 7 List of Figures Figure 3–1: MX8000 Front View ............................3–2 Figure 3–2: MX8000 Front View Without Front Plate Attached ..................3–2 Figure 3–3: MX8000 Rear View ............................3–2 Figure 3–4: Rack Mount Enclosure, Front View ......................3–3 Figure 3–5: Rack Mount Enclosure, Rear View .......................3–4...
  • Page 8 Figure 5–13: MX8000–LC3 Handshake Sequence Menu ...................5–39 Figure 5–14: MX8000–LC3 Handshake Order Number ....................5–39 Figure 5–15: MX8000–LC3 Line Options Menu ......................5–42 Figure 5–16: MX8000–LC3 Listen Mode Menu Display ....................5–44 Figure 5–17: MX8000–LC3 Listen In Accounts Menu ....................5–45 Figure 5–18: MX8000–LC3 Miscellaneous Phone Line Options ................5–46 Figure 5–19: MX8000–LC3 Ring Options...

  • Page 9: Section 1 System Overview

    This manual describes installation, operation, and programming of the MX8000 Digital Alarm Receiver. The MX8000 can be used as a desktop receiver, however it must be rack-mounted for UL Listed installations. This section will list features, optional accessories, compatible formats, and SIA options supported. This section also contains conventions held throughout the manual, terminology relevant to this product, and other information.

  • Page 10: Formats Compatible With The Mx8000

    The MX8000 receiver is compatible with all ADEMCO UL Listed communicators. Table 1–2 shows the formats that the MX8000 receiver can decode and the handshake frequency groups that accommodate that format (see Section 5.5 for line device programming). Each line device can decode every format listed below.

  • Page 11: Mx8000 Supported Sia Digital I-Iii Levels

    Section 1 – System Overview MX8000 Supported SIA Digital I-III Levels Table 1–3 compares the MX8000 receiver to SIA Digital Compatibility Levels I, II, and III and indicates which of them we comply with. Table 1–3: MX8000 and SIA Levels I-III comparison...

  • Page 12: Terminology

    LRR. When this feature is not used, the number of accounts that can report to one LRR is limited to 10,000. What’s in the Box This section contains a list of the parts that are shipped with the MX8000 receiver and a brief description of their intended use. Item...

  • Page 13: General Recommendations, Notes, And Limitations

    • When replacing a 685 or CP-220 with an MX8000, make certain that the ADEMCO Auto Options for each line match what was set in the 685 or CP-220. The following chart is provided as an aid in setting these options when converting from a 685.
  • Page 14 CAPS, or CP-220 automation protocols and are currently supported by most automation systems. 685 OR CAPS MODES - The example below allows up to 3 MX8000-LC3 cards giving 8 usable lines: For MX8000-LC3 (If using an LRR card, insert it as a replacement for the LC3 in slot 3.)
  • Page 15 Important Note: The use of Virtual Receiver/Line Numbers is recommended. The example below allows up to 12 MX8000-LC3 cards giving 36 usable lines: For MX8000-LC3 (If using an LRR card, insert it as a replacement for the LC3 in slot 3. LRR card not supported by CP-220 mode.)

  • Page 16: How To Contact Technical Support

    • Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. • Note your Honeywell customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively.

  • Page 17: Section 2 Agency Requirements

    Section 2 Agency Requirements Telephone Requirements If requested by the telephone company, the following information must be provided before connecting this device to the phone lines: Manufacturer: Honeywell International Inc. Model Number: MX8000 FCC Registration Number: US5GBOT01B46056 Type of jack (to be installed by the...

  • Page 18: Ul Requirements

    See Figure 3–4 and Figure 3–5 (Section 3) for diagrams of a suggested installation. 1. A second MX8000 must be installed as a backup in case the primary MX8000 fails. The backup system must be able to take over within 30 seconds. (Note: This requirement does not apply to burglary-only installations.)

  • Page 19: Operational Requirements

    The backup must either be in the form of a UL Listed UPS or electrical generator. 3. If the MX8000 is not automated, the central station operator must check for the 24-hour test signals from the communicators. (Note: This requirement does not apply to burglary-only installations.) 4.
  • Page 20 MX8000 Installation and Operation Guide 2–4...

  • Page 21: Section 3 Installation

    The following procedure provides a quick start outline that may be used by installers who are familiar with the installation and programming of the MX8000 receiver. This procedure encompasses the basic installation and programming steps where the unit will be using mostly default values for operation. For complete installation procedures, bypass this section and observe the procedures in the balance of this manual.

  • Page 22: Overview

    MX8000 Installation and Operation Guide Overview The MX8000 is assembled at the factory. One MX8000-LC3 tri-line card is shipped with the MX8000 receiver. Follow the procedures described in Section 3.7 to install additional line cards. SYSTEM SYSTEM OPERATOR CALL POWER...

  • Page 23: Rack Mounting

    Section 3 – Installation Rack Mounting This diagram shows how to mount the MX8000 in a UL Listed rack enclosure. Model MX8000 SYSTEM SYSTEM OPERATOR CALL POWER FAULT LOGGED IN PENDING Receiver PREV EVENT PREV NEXT CALL CALL DEVICE ENTER...

  • Page 24: Hot Swapping Of Line Cards

    1. While holding the front plate, unscrew the two front plate retaining screws located on the front of the panel. (See Figure 3–1 for front plate retaining screw locations.) 2. Open the MX8000's front panel by pulling the left side of the front plate slightly forward and then to the left to remove it from the receiver.

  • Page 25: Line Card Installation

    1. While holding the front plate, unscrew the two front plate retaining screws located on the front of the panel. (See Figure 3–1 for front plate retaining screw locations.) 2. Open the MX8000's front panel by pulling the left side of the front plate slightly forward and then to the left to remove it from the receiver.

  • Page 26: Figure 3-7: Line Card Position And Components

    When using a MX8000–LRR line card in FM installations, the 7810 Radio Transceiver connection to the MX8000–LRR must be within 20 ft. (6m) of the MX8000 and in the same room as the MX8000. 7. Restart the receiver in accordance with the procedures provided in Section 4.6.7.

  • Page 27: Removing Line Cards

    2. While holding the front plate, unscrew the two front plate retaining screws located on the front of the panel. (See Figure 3–1 for front plate retaining screw locations.) 3. Open the MX8000's front panel by pulling the left side of the front plate slightly forward and then to the left to remove it from the receiver.

  • Page 28: 3.10.1 Printer Cable Pin-Outs

    FOR EVERY 5 PRINTERS. COM 2 TO PRINTER Figure 3–8: Parallel Printer Cable Connection to MX8000 3.10.1 Printer Cable Pin-Outs 25 pin printer cables are standard items at most electronic stores; however, if you create your own cable, use the pin description in Table 3–1.

  • Page 29: Com Ports 1 And 2

    3.11 AC Power Cord Connection 1. Connect the appropriate end of the power cord into its receptacle on the back of the MX8000. 2. Plug the three-pronged end of the power cord into a 120 VAC 60 Hz outlet (three-prong type only). The outlet should be unswitched, so that power remains on 24 hours a day.

  • Page 30: 3.11.2 How To Verify Earth Ground

    3.11.2 How to Verify Earth Ground To verify earth ground at the AC outlet the MX8000 receiver is powered from, use the following steps: 1. Measure the AC voltage between the center ground post and each side of the outlet (see A & B in Figure 3–13).

  • Page 31: 3.12 Battery Connection

    Note: A UL approved 12VDC 7AH battery (such as a Powersonic 1270) will provide a minimum of 4 hours of battery backup power. (See 2.4.2 for UL requirements.) 1. Plug the Battery/Relay wiring harness onto the connector on the back of the MX8000 receiver. (See Figure 3–14.) 2.

  • Page 32: 3.13 Automation Computer Connection

    3.13 Automation Computer Connection An automation computer can be connected to Com Port 1 on the MX8000 receiver. Com Port 1 is a 9-pin DTE port. Refer to Section 8 for details on automation communication protocols. The diagrams below describe some of the cable options.

  • Page 33: 3.14.2 Master/Slave Linking Programming

    For FM installations, the printer or any automation system connection must be within 20 ft. (6m) of the MX8000 and in the same room as the MX8000. The Okidata Microline 320 is the only FM approved printer for use with the MX8000.

  • Page 34: Figure 3-18: Sbus Receiver Linking Cable

    MX8000 Installation and Operation Guide 5 4 3 2 1 RJ-11 2 3 4 5 6 CONNECTORS LOCK/UNLOCK LOCK/UNLOCK TAB UP TAB DOWN BLACK GREEN YELLOW 00-MX8000-005-V0 Figure 3–18: SBUS Receiver Linking Cable 3.14.2.1 Master Printer/Slave Printer Linking Programming To perform MasterPrn/SlavePrn Linking Programming, follow these steps: 1.
  • Page 35 Section 3 – Installation From the “3 Communications” display, select “1 Port Functions” and configure COM1 for “Automation” and parallel port for “Auto Bkp Prn.” Note: If a serial printer is being used as a automation backup printer, congigure COM2 as the “Auto Bkp Prn”...
  • Page 36 MX8000 Installation and Operation Guide 3–16...

  • Page 37: Section 4 Operation

    This section covers information on how to operate the MX8000 Receiver. Touchpad Function Buttons The front panel of the MX8000 is made up of; a touchpad, containing numbers, arrows and buttons; a VFD display; and an array of LED indicators. (See Figure 4–1.)

  • Page 38: Displays

    In manual mode this key is used to Enters a # Character when initiate the listen in feature. programming in an “Edit” field. See Table 5–1 for Types of Programming Fields, descriptions. Displays This section describes the two types of displays that the MX8000 receiver uses. 4–2...

  • Page 39: Led Displays

    The status display is a 4-line 20 character (each line) backlit VFD that shows the various alarm and function messages. It functions in all modes of operation (normal and programming mode). As the MX8000 acknowledges calls and messages, it updates the calls on the VFD and silences the alert tone.

  • Page 40: Initial System Power Up

    Area Number Area Initial System Power Up Apply power to the MX8000 by plugging in the AC power cable. (See Figure 3–3.) When the MX8000 powers up, the display will go through the routine shown in Figure 4–4. Powerup Screen...

  • Page 41: Log On / Log Off

    Log On / Log Off Persons operating the MX8000 must log on and off the system. This is a way of keeping track of who is operating the system at any given time. You can program a total of 40 codes. Each code will be assigned to one of two user profiles (Installer profile or Operator profile).

  • Page 42: How To Log Off The System

    If an invalid code is entered the VFD will display Access code not verified. Modes of Operation This section describes the different modes of operation for the MX8000 Receiver (normal mode and programming mode) and the options available in them.

  • Page 43: Program Mode

    Section 4 – Operation 4.5.1.3 Log Only Log only mode will log event data without manual acknowledgments or communications with the automation computer. All event information is intended for printer output. Notes: • • • • On initial power-up the receiver will default in manual operation. The receiver can be set to automatic or log only operation in program mode (see Section 5.4.1).

  • Page 44: How To Maneuver Through Main Menu

    MX8000 Installation and Operation Guide 4.6.2 How to Maneuver Through Main Menu Figure 4–6 indicates what keys on the touchpad are used to maneuver through the Main Menu. Menu Controls ENTER To accept a menu item press MENU Or press...

  • Page 45: System History

    Rev: G software date, and letter revision. The first line card firmware information LineCard Firmware: MX8000-LC3 display is for a MX8000–LC1 card, the 124061 second display is for a MX8000–LC3 Date: 4/02/02 ¯ card, and the third display is for a Rev: B MX8000–LRR card.

  • Page 46: System Restart

    MX8000 Installation and Operation Guide Set Time and Date 1. Press the Menu button. 2. Press the 4 button. 3. Set the Hour (1 to 12). Time: 12:00AM 7. Set the Day. Time: 12:00AM The field to be Date: 01/01/01...

  • Page 47: Printer Menu

    Definitions, System Options, and Message Queue System Config Options. Users List Print a list of assigned MX8000 Users with their Level (Installer or Operator) and PIN Number. Line Card # Print line card configurations per line card. These are the items programmed using the Line Card Menus.

  • Page 48: Figure 4-13: Print Report Menu Items

    MX8000 Installation and Operation Guide Table 4–6: Printer Menu Choices (cont’d) Printer Menu Choice 1 Choice 2 Comments Date/Time Y or N Indicates that this item will print on a report. Format Type Y or N Indicates that this item will not print on a...

  • Page 49: Figure 4-15: System Configuration Print Items

    Section 4 – Operation ENTER 2. Press the button to view the main menu items. MENU 3. Press for the printer menu. (See Figure 4–12.) 4. Press for print report menu. (See Figure 4–13.) 5. Press to print the system history. 6.

  • Page 50: Table 4-7: Event Format Choices And Meaning

    MX8000 Installation and Operation Guide How to Print Line Card Statistics Follow these steps to print line card statistics: 1. Log on to the receiver (see Section 4.4.4 for log on procedure). ENTER 2. Press the button to view the main menu items.

  • Page 51: Configure Printer

    Section 4 – Operation EXAMPLE OF THE EVENT PRINTOUT For this example example, a yes answer was entered in the event format options for Date/Time, Format Type, Reference Number, Call Separator, and Device Number. Example of Print in Normal Mode 05/25/2004 02:53:37PM Device #: 1-34 Format #: 50 Reference #: 62 Account #: 1000...

  • Page 52: Program Menu

    4/2 format 09 FSK0 FSK0 17 FBII 4+3+1 FBII 4+3+1 10 FSK1 FSK1 18 Modem IIE Modem IIe format 11 FSK2 FSK2 19 SIA 2000 (see note) SIA 2000 format Note: This format is not currently supported by the MX8000. 4–16...

  • Page 53: Figure 4-19: Message Queue Level

    Section 4 – Operation 4.6.10.2 Message Que Message Que gives a visual indication of how <Diagnostics> ­ full the message queue is. It does this with 2=Message Que 3 Event Log both a percentage indication and a bar graph ¯ 4 Format-Raw Hex (made of *’s).

  • Page 54: Figure 4-23: Line Statistics Display

    MX8000 Installation and Operation Guide 4.6.10.6 LC (Line Card) Statistics LC (Line) statistics allows you to view the call statistics of a specific Line in comparison to the total number of calls <Select Device Type> received. Select the Device 1=MX8000-LC3...

  • Page 55: Listen-In And Hang Up

    Listen-In has two modes of operation called common and PBX. When operating in the common mode, the line is available to be monitored locally for a period of time that is programmed into the MX8000 and the line card continues to monitor the call. When operating in the PBX mode, a listen-in call is transferred to a phone number that is programmed into the MX8000 and the line card will release the call.

  • Page 56: Pbx Operation

    Prior to performing listen-in functions on a PBX phone line system the receiver must be set up with the proper listen-in mode and PBX string. Refer to Sections 5.1 and 5.5.2.4 (MX8000–LC3) or 5.5.4.4 (MX8000– LC1) to properly program the receiver to handle PBX listen-in calls.

  • Page 57: Section 5 Programming

    Section 5 Programming This section lists the programmable features in programming mode and the procedures for each of them. The options available are general options, line card options, and user options. NOTE After you complete your programming of the receiver, it is recommended that you make a printout of the programmed values for reference.

  • Page 58: How To Maneuver Around In Program Mode

    MX8000 Installation and Operation Guide 5.2.2 How to Maneuver Around in Program Mode Figure 5–1 shows what keys on the touchpad are used to maneuver in program mode. Menu Controls ENTER To accept a menu item, press MENU Or press...

  • Page 59: Table 5-2: General Options Items And Description

    Section 5 – Programming Table 5–2: General Options Items and Description The below table is organized into the order that menu items are displayed when General Options has been selected from the Program Menu. The first column reflects the first menu displayed, followed by the subsequent menu displays based on the item selected.
  • Page 60 MX8000 Installation and Operation Guide Table 5–2: General Options Items and Description (cont’d) General Options Level 1 Choices Level 2 Choices Level 3 Choices Comments Items Packed (default) Each data packet to the automation computer contains multiple events. SK9000 Unpacked Each data packet to the automation computer contains a single event.
  • Page 61 Section 5 – Programming Table 5–2: General Options Items and Description (cont’d) General Options Level 1 Choices Level 2 Choices Level 3 Choices Comments Items Term = 013, Head = Only visible if ADEMCO 685, FBII220, 010, ACK = 006, or CAPS ONLY format is selected.

  • Page 62: Operation Mode

    MX8000 Installation and Operation Guide Table 5–2: General Options Items and Description (cont’d) General Options Level 1 Choices Level 2 Choices Level 3 Choices Comments Items If this is selected an indicator will be sent to the automation computer that...

  • Page 63: Display Options

    Section 5 – Programming 5.4.1.1 How to change the operation mode Follow these steps to change the operation mode of the receiver: 1. Log on to the receiver. (See Section 4.4.4 for log on procedure.) ENTER 2. Press button. MENU 3.

  • Page 64: How To Change Language Display

    MX8000 Installation and Operation Guide Table 5–4: Display Options and Descriptions (cont’d) Display Menu Choices Default Comments Items Attempts See Section 5.4.2.5 for step-by-step instructions. CPU Time ITI (Edit Options) CPU Type Panel Rev Arming Level FSK1 English If “English” is selected then the printer and VFD output for calls of these formats will be text descriptions.
  • Page 65 Section 5 – Programming 5.4.2.2 How to Change Time Format Display 1. Enter program mode. (See Section 5.1.) 2. Press for general options. 3. Press for display options. 4. Press until the display flashes on the time format field. 5. Press the button until the display flashes on the desired setting.
  • Page 66 MX8000 Installation and Operation Guide 10. Press the button until the display flashes on the desired month for daylight savings time to take effect. 11. Press to advance to the start week field. 12. Press the button until the display flashes on the desired week for daylight savings time to take effect.
  • Page 67 Section 5 – Programming ENTER 7. Press to change the setting of that option. MENU Note: Additional presses of the enter button will toggle the setting between Yes and No. 8. Repeat steps 6 and 7 for any other ITI display options you wish to edit. 5.4.2.6 How to Edit Format Options To set these display options follow these steps:...

  • Page 68: Communications

    MX8000 Installation and Operation Guide 4. Press until the display flashes on the bright field. 5. Press the button until the display flashes on the desired setting. ENTER 6. Press MENU 5.4.3 Communications In the communication option the installer can configure the <Communications>...
  • Page 69 Section 5 – Programming Table 5–5: Communications Options and Description (cont’d) Communications Choices Options Default Comments Menu ✔ 38400 19200 9600 7200 4800 Baud 2400 1200 D (# Data Bits) ✔ Com Port 1 ✔ S (# Stop Bits) Even P (Parity) ✔...
  • Page 70 MX8000 Installation and Operation Guide Table 5–5: Communications Options and Description (cont’d) Communications Choices Options Default Comments Menu 1-120 seconds 4 sec 15 seconds or less in UL applications. See Section Ack Timeout 5.4.3.5 for programming steps. Term=013 Only visible if ADEMCO 685, FBII220 or CAPS ONLY Head=010 format is selected.
  • Page 71 Section 5 – Programming Table 5–5: Communications Options and Description (cont’d) Communications Choices Options Default Comments Menu ✔ Yes = will annunciate if an event, trouble or fault Printer condition occurs. ✔ No = no annunciation if an event, trouble or fault Bkp Printer condition occurs.

  • Page 72: Figure 5-7: Initialization String Display

    MX8000 Installation and Operation Guide 4. Press to set Com Port1 parameters. 5. Press the button until the display flashes on the desired port setting. ENTER 6. Press MENU Note: See “How to Edit Init String (Com 1, Com 2, and Parallel Port)” in Section 5.4.3.4.

  • Page 73: Table 5-6: Initialization String Characters

    Section 5 – Programming Table 5–6: Initialization String Characters Character Description Numeric characters, which can be entered from the touchpad or up/down arrows. a-z and A-Z Alpha characters entered with the up/down arrows. Special Characters entered with the up/down arrows. : _ - .
  • Page 74 MX8000 Installation and Operation Guide How to Enable or Disable Hex Mode When Hex Mode is enabled, any call data that is determined to be bad will output in a Hex format. This feature is only available if ADEM 8000 or SK9000 automation protocol is selected.
  • Page 75 Section 5 – Programming 3. Press for communications. 4. Press to set up automation configuration. 5. Press until the time field is flashing. 6. From the number keypad enter the desired number or press the button until the display flashes on the desired setting. ENTER 7.

  • Page 76: Table 5-7: Iti Automation Format Options

    MX8000 Installation and Operation Guide Table 5–7: ITI Automation Format Options Option Choices Default Meaning Comments Log Recs Y (Yes) Log records identify the time and date of an incoming report. N (No) Y (Yes) Extended panel Identification code. See 8.9.2.2.

  • Page 77: Table 5-8: On-Board Annunciator And Auxiliary Relay Options

    Section 5 – Programming 4. Press to set annunciator configuration. A list of the annunciator output options appears. 5. Press the button to move through the annunciator output options. ENTER 6. When the equal sign highlights the option you wish to change, press MENU Note: Additional presses of the enter button toggle the setting between “yes”...

  • Page 78: System Options

    MX8000 Installation and Operation Guide 5.4.4 System Options In system options you can configure the backup battery <General Options> ­ configuration, the receiver ID number, and the normal state 4=System Options 5 Msg Queue Opt. of the auxiliary relay. ¯...

  • Page 79: Table 5-10: 685, Caps, And Cp-220 1-9/A-Z Entries

    Section 5 – Programming 5.4.4.2 How to Set the Receiver as a Single, Slave, or Master In large central stations, it may be desired to set up receivers in a master/slave relationship for reporting to a printer. To set the receiver to act as a single receiver, master receiver, or slave receiver, proceed as follows: 1.
  • Page 80 MX8000 Installation and Operation Guide 5.4.4.4 How to Configure Output for Bad Data Blocks This feature selects how bad data blocks will be sent from the receiver to the automation computer. If Strip Bad is selected then an indicator will be sent to the automation computer when a bad data block is received, but the actual bad data block will not be sent.

  • Page 81: Message Queue Options

    Section 5 – Programming 5. Press the button until the display flashes on the desired setting. ENTER 6. Press MENU To Exit: Press until you return to the main menu. 5.4.5 Message Queue Options Set the percentage of how full the message queue must <General Options>...

  • Page 82: Slave List

    MX8000 Installation and Operation Guide 5.4.5.3 Set the Event Release Time Used to define the maximum amount of time (in seconds) that the receiver will hold an event in memory prior to sending it to automation, VFD, and printer. The time begins at the beginning of the call or on an acknowledgement.

  • Page 83: Virtual Receiver/Line Numbers

    The use of virtual receiver numbers allows multiple receiver <General Options> ­ 7=Virtual Receiver numbers to be assigned in the same MX8000 or multiple < Exit Menu MX8000s if operating in the master/slave configuration. Each virtual receiver number can have from 1 to 99 line(s) assigned to it.

  • Page 84: Line Device Menu

    MX8000 Installation and Operation Guide To assign virtual receiver and virtual line numbers: Notes: • If virtual receiver/line numbers are being used, DO NOT assign a hunt group number to a line. If a hunt group number is assigned, it takes precedence and the virtual number will not be used.

  • Page 85: Table 5-11: Line Device Menu Options

    For more information Handshake see page 5–40 2. 1000 Sequence 3. 1000 Handshake 0-9999 In 1ms Duration periods MX8000– 4. 0900 5. 1000 3 Line 6. 1520 Edit Line Line # 1. 1250 For more information see page 5–40 2. 3200 3.
  • Page 86 MX8000 Installation and Operation Guide Table 5–11: Line Device Menu Options (cont’d) Select Line Device Device Type Menu Choice Choice Choice Choice Default Comments This feature selects the time period Inter-digit 0 or 1 ms to 2 between data blocks.
  • Page 87 Network (normally between the first and second ring.) This option should only be used when connected to a parallel or serial printer or equivalent. MX8000– Y (Yes) Initiates a 2-second Misc. Line Edit Line Line # delay at the start of...
  • Page 88 MX8000 Installation and Operation Guide Table 5–11: Line Device Menu Options (cont’d) Select Line Device Device Type Menu Choice Choice Choice Choice Default Comments In High Speed, messages with event codes of B, C, E, and BFSK Auto F are translated to ADEMCO High Speed messages.
  • Page 89 2, 3.5B, 4.8, is enabled as Gain 6, or 7dB described in Section 5.5.2.5. Ringer Hi or Sy Impedance MX8000– Choose Device(s) # that you wish to be 3 Line Use Default Device # programmed to factory (cont’d) defaults. Copy...
  • Page 90 MX8000 Installation and Operation Guide Table 5–11: Line Device Menu Options (cont’d) Select Line Device Device Type Menu Choice Choice Choice Choice Default Comments Defaults Device # Device Copy Existing See the The order in which the corresponding device will output numbers different handshakes.
  • Page 91 Yes or No Select this option if Partially you have multiple Extended extended data blocks for 3/ 1 or 4/1 formats. MX8000– Y (Yes) Y = dedicated or direct Edit Line Line # connect phone line. ✔ No (No) 1 Line (cont’d)
  • Page 92 MX8000 Installation and Operation Guide Table 5–11: Line Device Menu Options (cont’d) Select Line Device Device Type Menu Choice Choice Choice Choice Default Comments ✔ See page 5–62 for Not Used more information. Common Must not be used in Listen Mode UL installations.
  • Page 93 B and C are 4/2 Out translated to High ✔ High Speed Speed Opening and Closing messages, respectively. ✔ S/Fast MX8000– Edit Line Line # LAR300 1 Line (cont’d) (cont’d) ✔ Extended A sequence of 1234 B (cont’d)

  • Page 94: Add Line Device

    11. Press to use the programming of another Line. 5.5.2 Edit Line – MX8000–LC3 (3 Line) To edit an existing Line, follow these steps: 1. Log on to the receiver. (See Section 4.4.4 for log on procedure.) ENTER 2.

  • Page 95: Table 5-12: Mx8000-Lc3 Edit Line List Items And Description

    ENTER Press MENU The display will show a list of choices. Table 5–12 lists these choices and a brief description. Table 5–12: MX8000–LC3 Edit Line List Items and Description Edit Line List Description 1 Handshake Seq This function is used to program the handshake order and parameters for this Line.
  • Page 96 MX8000 Installation and Operation Guide To Change the Format Group: 1. Follow the procedures in Section 5.5.2. 2. Press for handshake sequence menu. 3. Press until the display flashes on the Format Group field. See Table 5–11 for valid entries.
  • Page 97 Timeout field. Note: When the Timeout field is set to 0 (recommended), the MX8000 uses an algorithm to determine the inter-digit time. When set between 1 ms and 2000 ms, the time entered will be used.

  • Page 98: Figure 5-15: Mx8000-Lc3 Line Options Menu

    Thresh=08 Sample=08 <Direct Cnct <=Exit> Figure 5–15: MX8000–LC3 Line Options Menu How to Set the Line Card for a Direct Line (Dedicated Line): Note: This option must only be chosen for panels that have a direct connect capability. The panel supplies all line bias and a PBX is not required.
  • Page 99 Section 5 – Programming To Change Country: The “Country” field selects the country of your choice. 1. Follow the procedures in Section 5.5.2. for Line Options menu. 2. Press 3. Press until the display flashes on the Country field. 4. Press the button to change the Country.

  • Page 100: Table 5-13: Valid Programmable String Characters

    MX8000 Installation and Operation Guide 5.5.2.4 Listen-In The listen in feature is used to perform two-way voice alarm <Edit Line :01> verification between the central station and the alarm ­ 4=Listen In installation site. 5 Misc. Line Opt. ¯ Note: See Section 4.7 on page 4–19 for a description of the 6 Ademco Auto Opt.

  • Page 101: Table 5-14: Account Characters

    3 Clear Account lowest available listen in account number slot (20 total listen in account numbers [strings]). Adding # XX Figure 5–17: MX8000–LC3 Listen In Note: The account numbers may contain wild card entries (* Accounts Menu and #) described in Table 5–14. Therefore, the 20 account numbers are actually up to 20 unique strings.

  • Page 102: Figure 5-18: Mx8000-Lc3 Miscellaneous Phone Line Options

    MX8000 Installation and Operation Guide To Edit a Listen-In Account 1. Press 2. Press the button until the desired listen in account is highlighted by the equal sign. ENTER 3. Press MENU 4. Enter the revised account number you wish to the account list. See Table 5–14.
  • Page 103 Section 5 – Programming How to Set Caller ID Caller ID information is only sent if the incoming call has no data contained in it. Notes: Caller ID to Automation – When enabled, Caller ID information is output to the automation system only in the event that no alarm data is received from a security system control panel.

  • Page 104: Figure 5-19: Mx8000-Lc3 Ring Options

    MX8000 Installation and Operation Guide ENTER 5. When the desired hunt group is flashing press MENU 6. To exit press To Change the Ring Options: <Edit Line :01> ­ 5 Misc. Line Opt. Note: The default ring options will function for most 6 Ademco Auto Opt.

  • Page 105: Figure 5-20: Mx8000-Lc3 Ademco Auto Output Options

    FBII output of FBII Super Fast or FBII LAR300. 42Out=H/S FBI=S/Fast Pls=Ext ExtOut=H/S <BFSK AutoOut<=Exit> How to Set BFSK Auto Output Figure 5–20: MX8000–LC3 ADEMCO Auto 1. Follow the procedures in Section 5.5.2. Output Options 2. Press for Ademco Auto Opt. menu (see Figure 5– 20).
  • Page 106 MX8000 Installation and Operation Guide 3. Press the button to change the option from HiSpeed to 4/2 or vice versa. ENTER 4. When the desired setting is flashing press MENU How to Set 3/1 Restore Output 1. Follow the procedures in Section 5.5.2.

  • Page 107: Figure 5-21: Mx8000-Lc3 Line Gain Options

    The display Flashes on the Xmit= field. OHGain=7.0db RImp=HI <TransmitGain<=Exit> 3. Press the button to change the transmit Figure 5–21: MX8000–LC3 Line Gain Options gain. ENTER 4. When the desired setting is flashing press MENU How to Set Receive Line Gain 1.
  • Page 108 MX8000 Installation and Operation Guide ENTER 5. When the desired setting is flashing press MENU 6. To exit press How to Set CID Monitor Caller ID Monitor allows the selection of different modes for decoding Caller ID. These are: •...

  • Page 109: Edit Line - Mx8000-Lrr

    5. When the desired setting is flashing press MENU 6. To exit press 5.5.3 Edit Line – MX8000–LRR To edit an existing Line, follow these steps: 1. Log on to the receiver. (See Section 4.4.4 for log on procedure.) ENTER 2.

  • Page 110: Figure 5-22: Mx8000-Lrr Line Edit

    MX8000 Installation and Operation Guide <Edit Line> 6. Press to edit Line. ­ L34=MX8000-LRR ENTER MENU < Exit Menu The display will show a list of the existing Lines. 7. Press the arrow buttons to move <Edit Line :34> through the available list.

  • Page 111: Table 5-15: Hexadecimal Alarmnet Number To Decimal Conversion

    4. When the desired setting is flashing press MENU Table 5–15: Hexadecimal AlarmNet Number to Decimal Conversion NOTE: The most significant bit in the MX8000 is suppressed. Entries of decimal 80 through 255 equate to hexadecimal 0 through 7F. How to Set A/B Network 1.

  • Page 112: Edit Line - Mx8000-Lc1 (1 Line)

    Press . The display will show a list of choices. Table 5–16 lists these choices and provides a brief MENU description. Table 5–16: MX8000–LC1 Edit Line List Items and Description Edit Line List Description 1 Handshake Seq This function is used to program the handshake order and parameters for this Line.

  • Page 113: Figure 5-23: Mx8000-Lc1 Handshake Sequence Menu

    <Seq # <=Exit> handshake to use for the type of communication format you are using with a panel. Figure 5–23: MX8000–LC1 Handshake Sequence Follow these steps to change the handshake order and Menu or the parameters associated with the handshake.
  • Page 114 MX8000 Installation and Operation Guide 4. Enter the desired value from the keypad or press the button to change the delay time. ENTER 5. When the desired handshake delay time is flashing press MENU To Change the Handshake Duration Time: The handshake duration is the length of time that the receiver will send a handshake tone.
  • Page 115 Timeout field. Note: When the Timeout field is set to 0 (recommended), the MX8000 uses and algorithm to determine the inter-digit time. When set between 1 ms and 2000 ms, the time entered will be used.

  • Page 116: Figure 5-25: Mx8000-Lc1 Line Options Menu

    Thresh=08 Sample=020 <Direct Cnct <=Exit> Figure 5–25: MX8000–LC1 Line Options Menu How to Set the Line Card for a Direct Line (Dedicated Line): Note: This option must only be chosen for panels that have a direct connect capability. The panel supplies all line bias and a PBX is not required.
  • Page 117 Section 5 – Programming To Change the Ring On Time: The “On” field controls the ring on time. The ring on time is the length of time the receiver will listen to a ring prior to recognizing it as a ring. 1.

  • Page 118: Figure 5-26: Mx8000-Lc1 Listen Mode Menu Display

    MX8000 Installation and Operation Guide 3. Press until the display flashes on the Thresh field. 4. Enter the desired value from the keypad or press the button to change the Line fault threshold level. Values range from 1 to 15 volts in 2.0 VDC increments (1=2.0VDC, 2=4.0VDC, 3=6.0VDC and so on).
  • Page 119 Section 5 – Programming 3. Press until the display flashes on the <Str> field. ENTER 4. Press MENU 5. Enter the desired numeric value from the keypad or press the button to enter any special characters. (See Table 5–13, page 5–44 for valid programmable string characters.) 6.

  • Page 120: Figure 5-27: Mx8000-Lc1 Listen In Accounts Menu

    MX8000 Installation and Operation Guide To Add a Listen-In Account Mode=Not Used Note: Panels that send listen-in commands (Contact ID E606 Timeout=000 ENTER MENU or SIA LF and LE) as part of their message do not need their <Account List>...

  • Page 121: Figure 5-28: Mx8000-Lc1 Miscellaneous Phone Line Options

    Echo Spr=N Call ID=Y BillDly=N HntGrp=00 HngUp=120 <Echo Suppress<=Exit> Figure 5–28: MX8000–LC1 Miscellaneous Phone Line Options To Change the Echo Suppress Setting: If echo suppression is enabled (Y) a 2025Hz signal will be output for two seconds to disable echo suppression equipment.
  • Page 122 MX8000 Installation and Operation Guide 3. Press until the display flashes on the BillDly field. 4. Press the button to toggle the billing delay between “Yes” or “No”. ENTER 5. When the desired setting is flashing press MENU To Change the Hunt Group: Note: If a Hunt Group number is assigned to a line that has a virtual line number assigned, the Hunt Group Number will take precedence and the virtual line and receiver numbers will be ignored.

  • Page 123: Figure 5-29: Mx8000-Lc1 Ademco Auto Output Options

    Pls=Ext ExtOut=H/S How to Set BFSK Auto Output <BFSK AutoOut<=Exit> 1. Follow the procedures in Section 5.5.4. Figure 5–29: MX8000–LC1 ADEMCO Auto 2. Press for Ademco Auto Opt. menu (see Figure 5– Output Options 29). The display Flashes on the BFSK= field.

  • Page 124: Copy Device(S)

    To Program the Default Settings Into a Device 1. Enter Program Mode (see section 5.1). 2. Press for Line Device menu. 3. Press (MX8000–LC3), (MX8000–LRR), or (MX8000–LC1) to select your line card type. 4. Press for copy Line Device menu. 5–68...
  • Page 125 Line Device menu. 3. Press (MX8000–LC3), (MX8000–LRR), or (MX8000–LC1) to select your line card type. 4. Press for copy Line Device menu. 5. Press the button until the equal sign is adjacent the Copy Existing option. See Table 5–11 for description.

  • Page 126: Clear Device

    The display will read <Warning!> LC01 MX8000–LC3 Delete Record No Note: The MX8000–LC3 shown above is an example only. The display will contain the number of the line card you are clearing. 7. Press the until Yes is flashing. ENTER 8.

  • Page 127: User List

    Section 5 – Programming User List User List is used to program and store the information on the <Program Menu> various installers and operators who will operate and ­ 3=User List maintain the receiver. Through this program menu item you <...

  • Page 128: Editing A User

    MX8000 Installation and Operation Guide Table 5–18: Available Characters Characters Comments Space, 0-9, :, -, _, ., ,, &, *, # The word “Space” indicates that a physical space would be inserted if this character were chosen. Upper case alphabetical characters Lower case alphabetical characters There are 16 characters available for each user name.

  • Page 129: Clearing A User Out Of The Receiver

    Section 5 – Programming To change the user name, press the arrow buttons to move through the available characters. (See Table 5–18 for list of available characters.) When the name change is complete press ENTER MENU ENTER If you do not want the PIN code changed, press MENU ENTER To change the PIN code, enter the desired code (4 to 9 digits in length) then press...
  • Page 130 MX8000 Installation and Operation Guide 5–74...

  • Page 131: Section 6 Compatible Reporting Formats

    This section lists all the reporting formats that are compatible with the MX8000 receiver. Table 6–1 shows the formats that the MX8000 receiver can decode and handshake frequency format group that accommodates that format (see Section 5.4.6 for line card programming). Each line card can decode every format listed below;...
  • Page 132 MX8000 Installation and Operation Guide (cont’d) Table 6–1: Formats compatible with the MX8000 Communication Handshake Format Name Description Group Format Group SX-III, SX-IVA Sends a 5-digit account code in a Bell 103 format 2225 Hz with checksum. The data is decoded into English SX-IVB account information.

  • Page 133: Format Numbers Used In Printer Output

    ADEMCO 8000, SK9000 or ITI Automation Protocol !WARNING! • If you are receiving Contact ID ® 10 format on your MX8000 receiver you must use ADEMCO 8000 automation protocol. • If you are receiving Contact ID ® format on your MX8000 receiver you may use any automation protocol except the SK9000 automation protocol.
  • Page 134 5. Some of ITI panels don't respond to the default 2225Hz handshake. They need a lot longer handshake duration than what we have in the MX8000 receiver. You don't want to change the default 2225Hz handshake (1st handshake group) because it's optimized for SIA panels. What you should do is to program the 2nd 2225Hz handshake group with a long handshake duration (say 2550 ms).

  • Page 135: Section 7 Troubleshooting

    Section 7 Troubleshooting This section contains a list of possible error messages and a troubleshooting process for each. Error Messages Table 7–1 lists the error messages that are displayed on the VFD of the receiver as well as the message sent to the printer.
  • Page 136 MX8000 Installation and Operation Guide Table 7–1: Error Messages (cont’d) VFD Messages Printer Message Description What to Do Error Error ✔ Expander Expander Trouble Trouble with a device connected to the Trouble SBUS. ✔ Expander Trbl Expander Trouble The trouble condition of a SBUS device was Restore corrected.
  • Page 137 Section 7 – Troubleshooting Table 7–1: Error Messages (cont’d) VFD Messages Printer Message Description What to Do Error Error ✔ Bkup Computer Bkup Computer A communication problem exists between Check cable Trbl Trouble the backup automation software and the connections. Verify receiver.

  • Page 138: Unrecognized Reports

    A user has logged off of the receiver. Unrecognized Reports The MX8000 provides an output to the printer when a report is received in an unrecognized reporting format. This may happen in cases where the automation protocol selected does not match the reporting format set for a client.

  • Page 139: Removing The Cpu, Ps, User Interface Assembly

    5. Replace the front plate by screwing in the front plate retaining screws. (See Figure 3–1.) Safe Mode Safe mode can be used to reset User #01 access code back to default of MX8000 regardless of its present setting. For Example, if the code for the installer (User #01) is lost and additional programming is required the receiver can be restarted in safe mode to return User #01 to an access code of 8000.
  • Page 140 MX8000 Installation and Operation Guide ✶ ✶ ✶ ✶ 3. Press the button, then the button. STATUS The display will read Safe Mode Activated ENTER 4. Press MENU 5. Enter the default Installer code or 8000. 7–6...

  • Page 141: Section 8 Automation Communication Formats

    We’ll reserve the term message for discussions of the string as a whole. The term “call from panel” will refer to the complete data stream from a panel to the MX8000. The term “event data” will refer to the actual data, (that is, alarms, troubles, and so on), that are part of a call from a panel.

  • Page 142: Reporting Formats And Automation Protocol Support

    MX8000 Installation and Operation Guide Reporting Formats and Automation Protocol Support Table 8–2 provides a listing of the reporting formats supported by each type of automation protocol in the MX8000. Table 8–2: Reporting Formats and Automation Protocol Support Automation Protocol...

  • Page 143: Ademco 8000

    Section 8 – Automation Communication Formats ADEMCO 8000 Because of the additional features and program capabilities of the MX8000 receiver over its predecessor the 9000 receiver, it was necessary to develop a new automation protocol. ADEMCO 8000 protocol addresses these needs. The following sections describes the three different types of data blocks (system message, heart beat message, and call message) that the ADEMCO 8000 will send to the automation computer, and the components of these data blocks.

  • Page 144: Table 8-5: Dialer Format Types By Code

    MX8000 Installation and Operation Guide 8.4.2.1 Dialer Format The ADEMCO 8000 format takes advantage of additional format numbers and outputs information with greater detail about the dialer format. Table 8–5 lists the dialer format code and indicates the type of dialer associated with that number.

  • Page 145: Table 8-7: Call Message Components

    The MX8000 receiver uses the following standards to identify a listen-in account: • First, the receiver searches for an embedded listen-in event in the panel data, depending on whether or not the reporting format supports listen-in.

  • Page 146: Table 8-8: Call Message With Listen-In Data

    Bad Data Field Indicator If the data received by the MX8000 is garbled or parts are missing the receiver will send a bad data indicator (<$23> used in the event block as a separator) before the block of corrupted data. A bad data block will contain a hex-ASCII dump of the data in ASCII form.

  • Page 147: System Message Block

    Section 8 – Automation Communication Formats Table 8–9: Bad Data Field Indicator Components Character Description <$23> Bad data indicator <aaaaaaaa> Bad data ASCII hex data dump. <$23> Bad data indicator <bbbbb> Bad data ASCII hex data dump. <$05> Account number field indicator <“123456”>...

  • Page 148: Heart Beat Message Block

    8000 indicating the MX8000 Receiver. <$7A><2 ASCII byte Receiver Battery/DC Trouble Restore – Note: The Receiver Model <$7A> = z Model #> Number output is 8000 indicating the MX8000 Receiver. <$7B> Computer Trouble <$7B> = { <$7D> Computer Restore <$7D>...

  • Page 149: Validation Byte (V-Byte)

    Section 8 – Automation Communication Formats Table 8–12: Link Test Components Component Description <$03> Message type identifier. <“051997”> Date information, consisting of six ASCII bytes. <$22> Separator <“074905”> Time information, consisting of six ASCII bytes <$22> Separator <“01”> Receiver number <$22>...

  • Page 150: Table 8-13: Response Messages By The Mx8000 Receiver

    MX8000 Installation and Operation Guide Table 8–13: Response Messages by the MX8000 Receiver ASCII Hex Character Name Description Character The request is granted. NACK The request is unrecognized because of one of the following reasons: • Checksum error • Invalid request code/format...

  • Page 151: Table 8-16: Log-Off Request Components

    Section 8 – Automation Communication Formats Table 8–16: Log-off Request Components Component Description <$4B> Command request identifier. See Table 8–14. <Receiver ID> Receiver ID number. 1 or 2 ASCII digits. <$22> Separator <User PIN> The user’s PIN code. <V-byte> Validation Byte (V-byte). See 8.4.5. <$0D>...

  • Page 152: Table 8-20: Extend Listen-In Period Request Components

    MX8000 Installation and Operation Guide 8.4.7.4 Common Listen-in Extend/End Request During a listen-in operation if the call requires additional time you can extend the listen-in period by sending an extend request. At the end of a listen-in call you can end the session by sending an end request.

  • Page 153: Ademco 685 Automation Protocol

    Low Speed 3x1, 4x1, and 4x1 Express Automation Protocols When the MX8000 is operating in the ADEMCO 685 mode and receives a 3x1, 4x1, and 4x1 Express transmission, the output protocol to the computer is as shown in Figure 8–1. Note that when a 3x1 transmission is received, the account number will be padded to 4 characters by the addition of a leading 0 to the account number.

  • Page 154: 685 Contact Id

    8.5.4 685 Contact ID When the MX8000 receives a Contact ID ® (also referred to as Point ID – PID) transmission while operating in the 685 mode, the output protocol to the computer is as shown in Figure 8–4. LFRG 1234 18 QXYZ GG FCCC CR...

  • Page 155: Table 8-23: Contact Id Event Definition Codes

    Section 8 – Automation Communication Formats Table 8–23: Contact ID Event Definition Codes EVENT DATA TYPE ALARMS Medical Alarms -100 100 Medical Zone 101 Personal Emergency Zone 102 Fail to report in Zone Fire Alarms -110 110 Fire Zone 111 Smoke Zone 112 Combustion Zone...
  • Page 156 MX8000 Installation and Operation Guide Table 8–23: Contact ID Event Definition Codes (continued) EVENT DATA TYPE 158 High temp Zone 159 Low temp Zone 161 Loss of air flow Zone 162 Carbon Monoxide detected Zone 163 Tank level Zone SUPERVISORY...
  • Page 157 Section 8 – Automation Communication Formats Table 8–23: Contact ID Event Definition Codes (continued) EVENT DATA TYPE Communication Troubles -350 and 360 350 Communication trouble Zone 351 Telco 1 fault Zone 352 Telco 2 fault Zone 353 Long Range Radio xmitter fault Zone 354 Failure to communicate event Zone...
  • Page 158 MX8000 Installation and Operation Guide Table 8–23: Contact ID Event Definition Codes (continued) EVENT DATA TYPE 462 Legal Code Entry User 463 Re-arm after Alarm User 464 Auto-arm Time Extended User 465 Panic Alarm Reset Zone 466 Service On/Off Premises...
  • Page 159 Section 8 – Automation Communication Formats Table 8–23: Contact ID Event Definition Codes (continued) EVENT DATA TYPE 573 Burg. Bypass Zone 574 Group bypass User 575 Swinger bypass Zone 576 Access zone shunt Zone 577 Access point bypass Zone 578 Vault Bypass Zone 579 Vent Zone Bypass Zone...

  • Page 160: Mx8000/685 System Messages

    929 Log-off User 8.5.5 MX8000/685 System Messages The MX8000 generates messages to the automation computer for system generated troubles/restores and operator generated troubles/restores while operating using the 685 automation protocol. These messages are listed in Table 8–24. CAPS Automation Protocol The CAPS automation protocol is the same as the 685 except in the case of the 4x2 and 4x2 Express.

  • Page 161: Table 8-24: Mx8000/685 System Messages

    Time Adjusted For DST IMPORTANT NOTE: A "Message Queue Full" system message indicates that the MX8000 call event buffer is full and the MX8000 receiver has gone into a "Stop Answering Mode". This has occurred because either the printer or automation system has failed and the MX8000 began logging events internally (eventually filling up its internal buffer).

  • Page 162: Fbii Cp-220 Automation Protocol

    GROUP NUMBER RECEIVER NUMBER Figure 8–8: CP-220 FBII Superfast Protocol A space will be sent as the zone digit any time that the MX8000 receives a zero or letter a for the zone digit. 8.7.4 CP-220 Contact ID When the MX8000 receives a Contact ID ® (also referred to as Point ID – PID) transmission while operating in the CP-220 mode, the output protocol to the computer is as shown in Figure 8–9.

  • Page 163: Cp-220/Silent Knight

    ALARM DIGITS ACCOUNT NUMBER GROUP NUMBER RECEIVER NUMBER Figure 8–11: CP-220/Silent Knight Format 1 (FSK 1) A space will be sent as the zone digit any time that the MX8000 receives a zero or letter a for the zone digit. 8–23...

  • Page 164: Mx8000/Cp-220 System Messages

    MX8000 began logging events internally (eventually filling up its internal buffer). No more calls will be accepted until the MX8000 can free up part of its event buffer to either the printer and/or automation system (depending upon how the system has been configured).

  • Page 165: Sk9000 Protocol

    System messages, (indicated when the first byte of the message is $01), are always sent separately. For example, if two line cards have a problem at the same time, the MX8000 will send one message for each line card. Validation Byte (V-Byte) 1 byte.

  • Page 166: Calls From Panels

    Long Calls The MX8000 can send up to 70 bytes per message to an automation computer. When event data is more than 70 bytes, the MX8000 breaks up the data into 70-byte chunks ending in a separator $2C, a V-Byte, and the end of message indicator $0D 8–26...

  • Page 167: Bad Data

    8.8.4 Bad Data When the MX8000 receives data it cannot interpret, it precedes the data with $23. The MX8000 accepts 20 characters of bad data. This allows operators to determine, if possible, the account number of the panel sending the bad data for troubleshooting purposes. Causes for bad data include: Noise on the telephone line and non-matching first and second rounds of data.

  • Page 168: System Messages

    All system messages are sent separately. For example, if two line cards have a problem at the same time, the MX8000 will send one message for each LinePort. The V-Byte and a carriage return ($0D) always follow system messages.

  • Page 169: Iti Generic Computer Format

    • If the computer NACKs the data, the MX8000 will immediately re-send the data. • If the computer NACKs a second time, the MX8000 will generate a computer trouble message. • If the computer does not respond the second time the MX8000 sends the data, the MX8000 will generate a computer trouble message.

  • Page 170: Table 8-31: Upper Nibble Description

    MX8000 Installation and Operation Guide 8.9.2.1 Control Panel Type and Zone Attribution Byte Byte 4 (see Table 8–30) of the report record is divided into upper and lower nibbles. The upper nibbles (4 most significant bits) contain the code indicating the panel type.

  • Page 171: Log Record

    Section 8 – Automation Communication Formats 8.9.2.3 Alarm Codes Table 8–34 lists the alarm codes used in byte 13 of the report record, and a description of the alarm codes. Table 8–34: Alarm Code and Description Alarm Codes Description Alarm Bypass Closing Report Dial out audio alarm...

  • Page 172: Test Record

    8.9.5 OKAY Record When the automation computer sends a supervisory character to the MX8000 receiver, the receiver will return with an OKAY record. An OKAY record (heartbeat) is sent periodically to the automation computer. How often the OKAY record is sent is set through programming (see Section 5.4.3.5 page 5–18).

  • Page 173: 8.10.2 General Record Structure

    Section 8 – Automation Communication Formats Table 8–38: Number and ITI Digit Equivalent Represented by Number ITI Digit 0 - 9 0 - 9 10 - 35 A - Z 36 - 61 a - z 8.10.2 General Record Structure Each record begins with <"|["><Record Type>...

  • Page 174: Table 8-41: Report Record Components And Description

    MX8000 Installation and Operation Guide Table 8–41: Report Record Components and Description Character Description <"|["> Start of record indicator. <R> Report record identifier. <"|IA1"> Unit ID = A, followed by receiver ID = 1. <"|LB"> Line Card #, B = 11. Acceptable values are 0-9, A (= 10), B (=11), C (=12).

  • Page 175: Table 8-43: Panel Type Characters

    Section 8 – Automation Communication Formats Table 8–42: Information Field Identifiers (cont’d) Field Identifier Description Acceptable Values Panel type and revision. One panel type code byte followed by a 4-digit revision number. See Table 8–43. Group and attribute information. Contact ITI for group and attribute information.

  • Page 176: 8.10.4 Test Record

    MX8000 Installation and Operation Guide 8.10.3.3 Condition Codes Condition codes are a one-digit character that indicates the nature of the call from a control panel to the receiver. Table 8–44 lists the different condition codes and their descriptions: Table 8–44: Condition Codes and Descriptions...

  • Page 177: 8.10.5 Supervisory Record

    Section 8 – Automation Communication Formats 8.10.5 Supervisory Record When the automation computer sends a supervisory character to the receiver, the receiver will answer with a supervisory record. A supervisory record (heartbeat) is sent periodically to the automation computer. How often the supervisory record is sent is set through programming (see Section 5.4.3.5 page 5–18).

  • Page 178: 8.11 Us Ascii Character Code

    MX8000 Installation and Operation Guide Table 8–47: Checksum Verification Process Character ASCII Code Additive Checksum XOR Checksum 00 + 7C = 7C FF ^ 7C = 83 7C + 5B = D7 83 ^ 5B = D8 D7 + 58 = 12F...

  • Page 179: Appendix A Programming Quick Chart

    Appendix A Programming Quick Chart Table A–1: Programming Quick Chart Program Mode Choices Choices Choices Choices Comments Options Manual See Section 4.5 for description of modes of operation. See also Section 5.4.1. Operation Mode Automatic Log Only English See Section 5.4.2 for details. Language español Not available at this time.
  • Page 180 MX8000 Installation and Operation Guide (cont’d) Table A–1: Programming Quick Chart Program Mode Choices Choices Choices Choices Comments Options 0 .. 9 PULSE 0 .. F Packed SK9000 Unpacked Format Config. (continued) Zero ACRON Space HISPEED Display Options Hispeed (continued) See Section 5.4.2.7.
  • Page 181 Appendix A – Programming Quick Chart (cont’d) Table A–1: Programming Quick Chart Program Mode Choices Choices Choices Choices Comments Options CAPS, SK9000, ADEM See Section 5.4.3.5 for details. Format 8000, ADEM 685, FBII 220, ITI Gen, ITIComp Y (yes) Feature is only available if ADEM 8000 or SK9000 automation protocol is selected.
  • Page 182 MX8000 Installation and Operation Guide (cont’d) Table A–1: Programming Quick Chart Program Mode Choices Choices Choices Choices Comments Options No Battery Bkp Yes or No See Section 5.4.4.1 for details. Battery Backup Battery Bkp Yes or No See Section 5.4.4.1 for details.
  • Page 183 Yes or No If “Yes” you have multiple extended data Extended blocks for 3/1 or 4/1 format. Y (yes) Y = dedicated or direct connect phone MX8000– Direct line. Line Device N (no) N = used for standard phone lines.
  • Page 184 MX8000 Installation and Operation Guide (cont’d) Table A–1: Programming Quick Chart Program Mode Choices Choices Choices Choices Choices Comments Options See Section 5.5.2.6 for details BFSK Auto HiSpeed or 4/2 3/1 Restore HiSpeed or 3/1 Ademco 4/2 Out Normal or HiSpeed...
  • Page 185 0-15 in 2.00VDC steps Sample Time 0-255 seconds. Line # (con- Listen In Mode Common, PBX, Not See Section 5.5.4.4 for details. tinued) Used MX8000– PBX string edit Up to 20 characters. Line Device screen Menu 1 Line Listen In Timeout 0-255 seconds?
  • Page 186 MX8000 Installation and Operation Guide A–8...

  • Page 187: Appendix B Receiver Update Procedure

    To update the MX8000 Receiver, perform the following procedure: 1. With the MX8000 Receiver POWERED OFF, connect the null modem cable to the “COM 2” port of the Receiver and the other end to the “COM 1” port on the PC.
  • Page 188 MX8000 Installation and Operation Guide EDITING THE BAT FILE You must edit the “bat” file supplied with your upgrade software if you are not able to use the COM 1 port on your computer. To edit the bat file: 1. In Windows, load Notepad.

  • Page 189: Appendix C Index

    MX8000-LC1 ..............5–56 SK9000................8–28 MX8000-LC3 ..............5–38 Acknowledge Time..............5–19 MX8000-LRR ..............5–53 Acknowledge Tone Duration Time Event Release ...............5–26 MX8000-LC1 ..............5–58 Extended Out MX8000-LC3 ..............5–40 MX8000-LC1 ..............5–68 Add Slave................5–26 MX8000-LC3 ..............5–51 ADEMCO 8000 ............... 8–3 ACKing ................8–9 FBII Out Bad Data................
  • Page 190 MX8000 Installation and Operation Guide Listen-in ................ 4–19, 8–5 Program Menu ...............4–16 ADEMCO 8000 ............8–11, 8–12 Programming ................5–1 Listen-in Add Programming Choices .............5–2 MX8000-LC1 ..............5–64 Programming Fields..............5–1 MX8000-LC3 ..............5–45 Pulse Extended Listen-in Clear MX8000-LC1 ..............5–68 MX8000-LC1..............5–64 MX8000-LC3 ..............5–50...

  • Page 191: Limited Warranty

    Seller shall have no obligation under this Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791.
  • Page 192 165 Eileen Way, Syosset, New York 11791 Copyright © 2006 Honeywell International Inc. www.honeywell.com/security ÊK5982V2lŠ K5982V2 11/06 Rev. A...

Table of Contents