Turn Area On; Turn All Areas On; Turn All Areas Off; Move To Area - Bosch Solution 16i User Manual

Solution16 User Guide
i
Areas > Commands >

Turn Area On

This menu allows you to turn an single area All On. If your
system has been configured to have multiple areas then
the keypad will prompt you to select the area you wish to
arm.
1. Enter [Master PIN] + [MENU]
2. Enter [MENU] + [2] + [0] + [1] + [OK]. If your system
has been configured to have more than one area,
the keypad will display the A = prompt. Enter the
Area number to Arm, then press [OK] to arm.
Areas > Commands >

Turn All Areas On

This menu allows you to turn on all areas that your PIN
has been assigned to at the same time All On. The keypad
displays below show the area icons 1 and 2 on indicating
that both Area 1 and Area 2 are armed.
1. Enter [Master PIN] + [MENU]
2. Enter [MENU] + [2] + [0] + [2] + [OK]. The keypad
will display the word "LEAVE" in the display and the
exit warning beeper will sound. You should leave all
areas now.
POWER
3. When exit time has expired, the keypad will display
that the home area (Area 1 in this case) is on, and
that area 2 is also on via the area icons.
POWER
Area icons will only display if programmed to do so
i
by your security installer.
Note
Areas > Commands >
Turn All Areas Off
This menu allows you to turn off all areas that your PIN has
been assigned to at the same time. At least one keypad
on the system must be in a diasrmed area before you can
access this command.
1. Enter [Master PIN] + [MENU]
16
L201
MENU 2-0-1
A=
L202
MENU 2-0-2
ON
AREA
ON
L203
MENU 2-0-3
2. Enter [2] + [0] + [3] + [OK]. The system will now
disarm all areas that are in the armed condition
provided the user belongs or has access to the area.
Areas > Commands >

Move To Area

This menu allows you to move the focus of a keypad from
one area to another. Once the keypad's focus has changed,
you will be able to see the status of the zones in that area
and also perform functions as if you were using the keypad
locate in that area.
1. Enter [Master PIN] + [MENU]
2. Enter [2] + [0] + [4] + [OK]. If your system has been
configured to have more than one area, the keypad
will display the A = prompt.
Enter the Area number to move to, then press [OK].
3. The keypad will now move to the requested area.
If you do not have acces to the selected area the
system will sound a trouble beep and the keypad
focus will remain un-changed
The keypad displays the area which is currently in
focus at all times. In the above example, Area 3 is in
focus.
4. The keypad will return to it's home area, 30 seconds
after the last key press.
If the keypad has been programmed to be a roaming
i
keypad then you can use the [←] and [→] keys to
Note
move between areas at any time.
Areas > Commands >
Chime On/Off
Chime mode allows you to monitor a zone (or group of
zones) while the system or area is in the disarmed state.The
system can be programmed to sound the keypad buzzer or
activate a programmable output when the corresponding
Chime zone or zones are triggered. This feature can be
useful when you need to monitor the front or back entrance
to the premises.
This menu allows a user to turn chime mode on and off.
Only keypads programmed to sound the chime tone will
be heard when a zone programmed for chime is faulted.
The master user can program which zones are monitored
for chime alarms in menu location 3-0-3.
1. Enter [Master PIN] + [MENU]
2. Enter [2] + [0] + [5] + [OK]. The system will display
the current chime state. If your system has been
configured for multiple areas you will be prompted
to enter the area number to program.
In the example below chime mode " IS OFF".
L204
MENU 2-0-4
A3 OFF
ChOnOF
MENU 2-0-5
Bosch Security Systems 10/07 BLCC500U FTR1.01