Input Options; Zone Status; Bypass Zones; Set Chime Zones - Bosch Solution 16i User Manual

Solution16 User Guide
i

Input Options

The control panel has up to a maximum 16 zones. When
the optional radio receiver is fitted any available zone
can be programmed as a wireless zone. Your installer will
advise you on the exact makeup and configuration of your
system.
Inputs > Commands >

Zone Status

This menu allows you to view the status or condition of
each zone on the system. There are three possible states
which can be displayed, Zone Normal, Zone Open or
Zone Shorted. The status display will also show the zone
resistance which is being measured by the control panel.
1. Enter [Master PIN] + [MENU]
2. Enter [3] + [0] + [0] + [OK]. The keypad will display
the Zn = prompt. Enter the zone number you want
to check, then press [OK].
3. The keypad will display the zone status information.
The first screen will display the zone state.
There are 3 possible states;
Normal - Zone is closed and ready.
Short - Zone is shorted and not ready.
Open - Zone is open and not ready
4. The second screen will display the zone resistance
in ohms. This is the actual resistance being
measured by the control panel.
5. Press the [OK] key to exit.
Inputs > Commands >

Bypass Zones

This menu allows you to bypass one or more zones before
you arm the system in All On, Part On or Part 2 On modes.
When a zone is bypassed, it is not able to detect intrusion
or sound an alarm. All non bypassed zones will continue to
operate as normal.
A burglary zone will automatically be un-bypassed when
you turn the corresponding area off (disarm). Any 24-Hr
fire or 24-Hr non fire zones will need to be manually un-
bypassed.
1. Enter [Master PIN] + [MENU]
18
stAtus
MENU 3-0-0
Zn=
1
NORMAL
03198
BypAss
MENU 3-0-2
2. Enter [3] + [0] + [2] + [OK]. The keypad will display
the Zn= prompt which will flash indicating that
you are in data entry mode. Any zone(s) which are
currently bypassed will also be flashing.
If your system is configured for multiple areas the
area Icon for the current area will also be displayed.
You can only bypass zones in the current area.
i
To bypass zones in another area, exit progamming
Note
mode and move to the required area before
repeating from step 1.
3. To bypass a zone, enter the zone number and then
press [OK] . The zone indicator will begin to flash.
To un-bypass a zone type the zone number and then
press [OK].
3 4
4. Repeat step 2 for any additional zones that you
need to bypass.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
You can also access the Zone Bypass function by
i
entering your PIN and then ressing the PART /Bypass
Note
key down for 2 seconds.
Inputs > Commands >

Set Chime Zones

This menu allows you to program zones to be monitored
when the system is turned off. Chime mode is ideal to
monitor a front door to sound the keypad buzzer when
opened (faulted).
1. Enter [Master PIN] + [MENU]
2. Enter [3] + [0] + [3] + [OK]. The keypad will display
the Zn= prompt which will flash indicating that
you are in data entry mode. Any zone(s) which are
currently set as Chime Zones will be displayed.
If your system is configured for multiple areas the
area Icon for the current area will also be displayed.
3. To set a Chime Zone , enter the zone number
and then press [OK] . The zone indicator will be
displayed. To remove the chime zone, type the zone
number and then press [OK].
1 3
4. Repeat step 3 for any additional chime zones.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Zn=
1
Ch-zn
MENU 3-0-3
Zn=
1
Bosch Security Systems 10/07 BLCC500U FTR1.01