Volume; Contrast; Backlight; System Options And Events - Bosch Solution 16i User Manual

Devices > Keypads >

Volume

This menu allows you to adjust the volume of the keypad's
buzzer. Each keypad can have their volume adjusted
separately to suit your needs.
1. Enter [Master PIN] + [MENU]
2. Enter [6] + [1] + [0] + [OK]. The keypad will display
the current volume setting and the keypad address.
This example shows keypad 1.
1
3. Press the the [↑] and [↓] keys to adjust the volume.
Min = 1, Max = 8 , 0 = Off.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Devices > Keypads >

Contrast

This menu allows you to adjust the contrast of the keypad's
LCD display. Under certain lighting conditions you may
need to adjust the contrast to improve visability. Each
keypad can have their display adjusted separately.
1. Enter [Master PIN] + [MENU]
2. Enter [6] + [1] + [1] + [OK]. The keypad will then
display the contras screen which includes all of the
available symbols and the current contrast setting.
CHIME PHONE
( )
( )
1 2 3
9 10 11

POWER FIRE ALARM
3. Press the the [↑] and [↓] keys to adjust the contrast.
Min = 1, Max = 3.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Devices > Keypads >

Backlight

This menu allows you to adjust the brightness of the
keypad's LCD display backlight. Each keypad can have
their display adjusted separately.
1. Enter [Master PIN] + [MENU]
2. Enter [6] + [1] + [2] + [OK]. The keypad will display
the current backlight setting and the keypad
address. This example shows keypad 1.
1
3. Press the the [↑] and [↓] keys to adjust the contrast.
Min = 1, Max = 10, 0 = Off
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Bosch Security Systems 10/07 BLCC500U FTR1.01
CP-Vol
MENU 6-1-0
Uol =6
CP-Con
MENU 6-1-1
AREA
4 5 6 7 8
12 13 14 15 16
!
M
SERVICE PART OFF ON
CP-bl
MENU 6-1-2
bl =8

System Options and Events

Options in this section relate to programming of system
wide options and interpretation of system trouble events
when and if they occur. Your installer will advise you how
to interrogate system trouble events.
System > Commands >

Panel Status

The panel staus menu displays the panel software version
information as well as highlighting any system troubles
that are currently in effect. This is a view only menu.
System > Commands >

System Trouble

The System Trouble Menu provides a list of any system
troubles or problems. If more than one trouble is in effect
the keypad will list them one at a time. This is a view only
menu.
To learn more about the possible trouble events that the
system will report, see the Trouble Messages table later in
this user guide. If you are uncertain about any messages
you should contact your installer for more information.
Some trouble examples are listed below.
1. Enter [Master PIN] + [MENU]
2. Enter [7] + [0] + [1] + [OK]. The keypad will display
the device or devices which have a trouble
condition. In this example, there is a panel trouble
in effect. Use the [↑] and [↓] keys to select the device
if more than one, and then press the [OK] key to
view the trouble events.
3. Trouble events are displayed one at a time, one
per screen. The keypad will display -------- when all
troubles have been displayed before scrolling back
to the first trouble event.
Display indicates the
telephone line is not
connected.
Display indicates that
the panel time and
date has not been set.
Displays when
the external siren
has failed or is
disconnected.
4. When finshed press [OK] to exit. The system will
automatically exit this menu after 30 seconds.
Solution16 User Guide
i
?????
MENU 7-0-0
TRbl
MENU 7-0-1
P001
No Tel
DAte
Contrb
25