Monitor Connector - Sony XDS-1000 Operation Manual

d REF. VIDEO INPUT (reference video signal input)
connectors (BNC type)
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector (IN),
the same signal is input from the right connector (
a connected device. When no connection is made to the
right connector, the left connector is automatically
terminated with an impedance of 75 ohms.
e Redundant power supply unit installation section
When using this unit in a system that requires high
reliability, you can back up the unit's power supply by
installing the optional XDBK-101 Optional Power Supply.
This allows operation to continue even if one of the power
supply units fails.
To enable continuous operation after failure, set
maintenance menu item M22: OPTION SETTING
>REDUNDANT PSU to "ON".
Note
The power supply and XDBK-101 do not support hot
swapping. Always turn the main power switch off before
exchanging the power supply or adding the XDBK-101.
f SYSTEM TC INPUT (system timecode input)
connector
If you want to input the broadcast station reference
timecode signal of a broadcasting station as time data
information, use this connector to input it.
g REMOTE (9P) (remote control 9-pin) 1, 2
connectors (D-sub 9-pin)
REMOTE (9P) 1 connector: Controls the recording port.
Connect a controller that supports the VDCP
protocol.
REMOTE (9P) 2 connector: Controls the playback port.
Connect a VTR or a controller that supports the
RS-422A Sony 9-pin VTR protocol (see page 33).
h VIDEO CONTROL connector (D-sub-9-pin)
Connect an HKDV-900 video control unit.
See page 107 for correspondence between setting items of
HKDV-900 and setup menu of this unit.
i GPIO (general-purpose I/O) connector
When you are using this unit in a larger system, such as a
playout system, this connector allows you to connect an
external device to control this unit's playback, and to
return tally and alarm signals to the external device.
j MONITOR connector
Outputs the same video that appears on the display of this
unit's front panel as analog RGB component video signals.
This connector is intended for connection to the VGA
input connector of a PC monitor.
k MAINTENANCE connectors
These are the USB connectors for maintenance.
l
(network) connector (RJ-45 type)
) to This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
CAUTION
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• When you connect the network cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
ATTENTION
• Par mesure de sécurité, ne raccordez pas le connecteur
pour le câblage de périphériques pouvant avoir une
tension excessive à ce port. Suivez les instructions pour
ce port.
• Lors de la connexion du câble réseau de l'appareil au
périphérique, utilisez un câble blindé afin d'empêcher
tout dysfonctionnement dû au bruit de rayonnement.
VORSICHT
• Aus Sicherheitsgründen nicht mit einem
Peripheriegerät-Anschluss verbinden, der zu starke
Spannung für diese Buchse haben könnte. Folgen Sie
den Anweisungen für diese Buchse.
• Verwenden Sie beim Anschließen des Netzwerkkabels
des Geräts an ein Peripheriegerät ein abgeschirmtes
Kabel, um Fehlfunktionen aufgrund von Störungen zu
vermeiden.
m COMPOSITE OUTPUT (analog composite video
output) 1, 2 (MONITOR) connectors (BNC type)
Output analog composite video signals. Output signals of
the 2 (MONITOR) connector are E-E signals or playback
signals, according to the setting of the REC PORT and PB
PORT buttons on the front panel. You can superimpose
timecodes or error messages on the output of the 2
(MONITOR) connector when CHAR SEL on the HOME
page of the function menu is set to ON.
See "Basic Operations of the Function Menu" on page 41
for more information about the CHAR SEL setting.
25
Rear Panel