Ricoh Aficio GX e3300N User Manual page 705

D-
1. Remove the cover from the rear
Remove carriage
3
side of the carriage unit.
Fit the carriage unit into the Styrofoam
holders as shown in the photo.
Cover
2. Remove the 2 FFCs.
3. Secure the FFC to the jigs.
Removal of the carriage unit
completed.
Appendix: Accessories
1. Carriage unit 2. Procedure
5. Guide rod fastening tool (x2;
6. Main scan encoder
right side of photo), guide rod
sheet
removal tool (x1; left side of photo)
Notice:
Please be informed of the following as this kit is commonly used with Japanese models.
• Both English and Japanese procedure are bundled.
• Ink cartridges are are labeled in Japanese but can be used in all models.
Attach new carriage 3. Remove the humidity retention cap.
1. Attach the 2 FFCs.
Humidity retention
cap
4. Re-insert the guide rod into the
carriage. (See Step C-4)
5. Remove the jigs. (See Step C-2)
CAUTION:
Be careful not to fold them.
6. Attach the belt.
One FFC is longer than the
other. Make sure to attach the
Upper
longer FFC in the right position
belt
shown in the photo in Step D-2
(and shorter FFC in the left
position).
Do not fold the FFCs
Carriage
Lower
belt
Slide the belt into the gap
2. Attach the carriage's rear cover.
7. Pass the bundled encoder strip
(not the original encoder strip)
through the opening between the
carriage sensors.
3. Waste ink tank 4. Ink cartridges
Left
Right
Hole
Left
side
Marking
Left
Through this
10. Attach the cam (screw x1). See Step C-3-5.
opening
Right 11. Attach the spring. See Step C-3-4.
12. Attach the linkage. See Step C-3-2.
8. Hook the right end of the
encoder sheet first, then hook the
13. Attach the stay plate.
left end.
Left
Right side
9. Clean the strip with alcohol by
14. Attach the guide lock. See Step C-3-3.
wiping the surface from right to
15. Attach the ink supply unit See Step B-1.
left.
16. Attach the front cover. See Step A-7.
17. Attach the operation panel. See Step A-6.
18. Attach the right cover.See Step A-4.
19. Attach the upper/inner cover. See Step A-3.
20. Attach the ink cartridge cover. See Step A-5.
5 21. Attach the output tray and paper
Clean from right side
22. Reset the envelope lever to standard position.See Step B-2.
CAUTION:
If you wipe the surface from the Carriage attachment completed.
left side, this may damage the
plate spring.
Adjustment after replacement
F
1. Open the ink cartridge cover before you turn on
the machine main power. Otherwise the machine
will perform auto maintenance and consume a large
amount of ink.
2. Enter SP mode.
Plate
spring 3. Execute SP5101.
(Some values related to print head will be reset)
4. Install the starter ink cartridges.
5. Install the ink collector unit.
6. Close the ink cartridge cover.
IMPORTANT: Ink initialization will start. During the initialization, do not
open any covers, or turn off the power. The entire process will take
about seven minutes.
7. Print out the nozzle check pattern.
[Menu] [Maintenance] [Nozzle check]
IMPORTANT: Check to see if the nozzle is clogged, and If it is, perform
print head cleaning.
8. Adjust the print head position.
[Menu] [Maintenance] [Head Position]*1
9. Adjust the registration.
Order to fasten screws
[Menu] [Maintenance] [Registration]*2
10. Adjust the paper feed.
[Menu] [Maintenance] [Adj. Paper Feed]
11. Print out the color demo page.
[Menu] [List/Test Print] [Color Demo Page]
12. Print out the engine summary (SP 5200).
13. Replace the ink collector unit and ink cartridges with the ones
the customer was originally using.
*1: Standard - High Speed - High Quality
tray. See Step A-1 and 2.
6
*2: Only "Tray 1-Plain Paper"
Copyright © 2009
Printed in China
EN GB EN US J017-6701A