Roland V-Mixer VM-3100 Owner's Manual page 52

52
PIE SI IE TITRE
Returning to the prior when editing routings
1. Hold down the [SHIFT] button and press [EXIT/NO].
2. Press [ENTER/YES].
SERRE RS ET
Saving routing settings
1. Press [EZ ROUTING].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press any of the buttons [F1] (IN)-[F3] (FX).
4. Press [F1-F4 ON/OFF]. The functions appear in the display.
5. Press [F4] (SAVE).
6 Press [7] toselect "To No.**."
7. Rotate the VALUE dial to select a position to save your
settings to.
8. Press [ 1] to select "Name" and "Memo."
9. Use the [7], [+], — J, and [ 4 } buttons and the VALUE
dial to set the Name and write a Memo for the routing
settings.
* By pressing [F1] (Ins), you can insert one character at the
cursor position; press [F2] (Del) to delete one character at the
cursor position.
10. Press [ENTER/YES] two times.
LL LR A ET TATA
Deleting Unneeded routing Settings (Delete
EZR Set)
1. Press [EZ ROUTING].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F4] (DEL).
4. Rotate the VALUE dial to select the routing number you
want to delete.
5. Press [ENTER/YES] two times.
@ INPUT
Using a condenser mic (Phantom Power)
J. Press [SYSTEM].
2. Press [ J ] to select "Phantom."
3. Rotate the VALUE dial to select "ON."
* Turn the Phantom Power setting fo "OFF" when a device that
does not require phantom power is connected to INPUT 1 or 2.
Displaying the Level Meter for Channels 13-20
(VM-3100Pro only)
1. Press [AUDIO CH] until the button's indicator lights green.
* To prevent hazard or damage, ensure that only microphone
cables and microphones designed to IEC-268-15A are
connected.
* Afin d'éviter tout risque ou dommage, ne brancher que des
cables de microphone et des microphones conformes @ la norme
IEC-268-15A.
TLE TET TE I ITI SEA
Inputting signals from digital devices
1. Use a digital coaxial or optical cable to connect the digital
output of the digital device to the VM-3100's DIGITAL IN A
or B connectors (A is coaxial, B is optival).
2. Hold down [SHIFT] and press [DIGITAL IN] (CLK SELECT).
3. Rotate the VALUE dial or press [F2] (>DinA) or [F3] (>DinB)
to select "DIN-A" or "DIN-B."
* When setting "A" or "B," select the one corresponding to the
name of the connector to which the digital cable is conmected.
4. Raise the Channel 11-12 fader to a suitable level.
Be IRS Sh cy 1 ha OER SS SS BS a Rt tn ea
Listening to a CD player connected digitally to
channels other than Channel 9-10
1. Hold down [SHIFT] and press [SELECT] for the channel
you want to assign the digital input to.
2. Press { T ] to select "Source."
3. Rotate the VALUE dial to select :DIN-L" and "DIN-R"
(DIGITAL INPUTS).
nega Sam nao Nn Ion oem arER EE Nn aeiannnrerT aS
Digitally increasing the input levels of INPUT
9-12
1. Hold down [SHIFT] and press [SELECT] for the channels
from which INPUT 9-12 are connected.
2. Press [ 1 ] to select "D.Boost (9/10)" or "D.Boost (11/12)."
3. Rotate the VALUE dial to select "ON."
* When set to "D.Boost=ON," signals from INPUT 9-12 are
increased by 18 dB.
@ EFFECTS
Turning effects on and off
1. Press [EFFECTS 1].
* On the VM-3100Pro, press [EFFECTS 1] or [EFFECTS 2].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F1] (>OFF) or (>ON). The effects are turned on or off.
* You can confirm whether the effects are on or off by checking
"EFFECTS" in the display.
a pe A A SE ESTAR SIE I
Selecting effects patches with the [VALUE] dial
1. Press [EFFECTS 1].
* On the VM-3100Pro, press [EFFECTS 1] or [EFFECTS 2].
2. Rotate the VALUE dial until the name of the patch you want
to select to appears in the display.
3. Press [ENTER/ YES]. The patch is switched.
La en]
Adjusting effect settings
1. Press [EFFECTS 1].
* On the VM-3100Pro, press [EFFECTS 1] or [EFFECTS 2].
2. Press the [ — ] or [ - ] button or rotate knobs [V1]-[V4] to
select the screen for the effects parameter you want to
adjust.
3. Rotate knobs [V1]-[V4] to change the values of the indicated
effects parameters.
SS RA
Changing the effects' mixer location
1. Press [EFFECTS 1].
* On the VM-3100Pro, press [EFFECTS 1] or [EFFECTS 2].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F2} (LOC).
4. Press{ ] to select "Location."
5. Rotate the VALUE dial to select the effects location.
AREA AI EE I,
Using effects at fixed output levels
1. Press [EFFECTS 1].
* On the VM-3100Pro, press [EFFECTS 1] or [EFFECTS 2].
2. Press [F1-F4 ON/OFF]. The functions appear in the display.
3. Press [F2] (LOC).
4. Press[ T ] to select "LKnobSw."
5. Rotate the VALUE dial to set this to "OFF."
* Fine adjustments to the effect output level can be made with the
"Out Level" control in the same screen.
Ie EL RE TET
Adding the "Vocal Multi" effects to Channel 1
1. Press [EFFECTS 1].
2. Press [PATCH SELECT] one or more times until the
"Vo MULTI" lamp is lit.
* To select patches with the dial: rotate the VALUE dial to
change to the desired patch number, then press [ENTER/YES].
3. Press [F1-F4 ON/OFF]. The functions appear in the display.
4. Press [F2} (LOC).
5. Press [ 4 ] to select "Location."
6. Rotate the VALUE dial to select "INS CH1."