Table of Contents
Advertisement
b. pre.ss DSS button
where
call is to be
transferred.
c. Hang up (station
1 and
2
are connected).
Intercom
transfer
using
DSS buttons
with
Search and Recovery
a
b.
Receive or make an intercom
call using
a DSS button.
C.
d.
Press
DSS button
to search
for 2nd
Party*
Press TRANS button
to recover
1st call
and abort transfer.
Repeat the last two steps until 2nd party
is located.
e. Hang up (Station
1 and 2 are connected).
400.37
LAST NUMBERREDLAL
a Press SPEED CALL button.
b. Press pound
[#I key.
mekLstnumbercifaLedoveranoutsideiine
udbevredialed
The system
will automaticaUy
select the
original
line used to place the call and re-
dial the number.
If that line is busy, the system will auto-
matically
select another
line fi-om the same
group
and red&l
the number.
If no lines are available
in the same group,
station
will receive busy tone and can
queue for a line.
If the station
user preselects
a line before
activating
LNR
the preselection
will over-
ride the line which
was used or&inaIy.
400.38
LEAST
COST ROUTING
To place an outside
call when LCR has been
enabled
in the system:
a Dial 191 on the dial pad.
b. Dial desired
7-digit
telephone
number.
(ie: l+ area code+number)
c. Wait
for answer.
Lift
handset
or use
speakerphone
to converse.
If all lines available
to pu
are busy, remain
off--hook for fm
(4) seconds
to mtomficdly
bequeuedontoLCRforanauatlableUne.
LCR Que Callback
If an LCR Queue
Callback
has been
acti-
vated:
a When telephone
is signalled.
answer the
call.
b. Desired telephone
number
will automat-
ically be redialed.
NOlE:Or&oneLCRQueueCullEhckrequest
may~~byastationWhenasewnd
reqzu3t is made, timt
request will be can-
celed..
400.39
LCR QUE CANCEL
a. Dial the LCR Queue Cancel code, (74 on
the dial pad.
b. Replace handset
or press ON/OFF
but-
ton
400.40
MEETMEPAGE
To request
another
party
to meet you on a
page:
a Dial the desired two-digit
paging
code:
or
Press pre-programmed
flex button
b. Request that party meet you on the page.
c. Do not hang up; wait for the requested
party
to answer.
As soon as the paged
party answers
and is connected
to you,
the page circuit
is released.
AnswerI$
a Meet Me Page
a. Go to the nearest Telephone
and dial [*I.
I91 on the dial pad:
or
Press the pre-programmed*
flex button.
b. You will be connected
to the party
that
paged you.
*Refer b FLEXButton
progmmming.
400.41
MESSACE
WAITING
Leaving
a Message Waiting
Indication
a. Press the MSG WAIT button.
b. Called
party's
MSG WAIT button
will
slow flash.
c. Hang up.
Upbjlverrzessagescunbeleftatany
Station
Ifyou
dial a station
that is busy, una&mied
orinDND,youamleaueamessagezmitfng
fndimUon.
Answering
a Message Waiting
Indication
If your MSG WAIT button
is flashing
at a slow
rate, you have a
message waIt.tng for you.
a.
b.
C.
Press flashing
MSG WArI' button.
Station
that left message will be signaled
with tone rlnglng.
If called station
does not answer,
press
MSG WAIT button
once to leave mes-
sage.
The fist
message
Left will be the first
one
cnLled
Issue 1, January
1992
400-13
Advertisement
Table of Contents
