Table of Contents
Advertisement
MAINTENANCE
AND TROUBLESKOOTING
Injinite
4096
Hybrid
Key Telephone
System
Sta
105:
State-
W~IT~COl~SZ~RSP,
Evt=
Seize
Ack
(101,
Data=0
Sta
105:
State-
COL-CONNECTED,
Eut=
Dial
Pad
(261,
Data-9
Co1
38:
State-
OUTPULSING,
Evt-
outpulse-digit,
Data-9
Co1
08:
State-
OUTPULSING,
Ewt=
Digit
Sent,
Data-0
Sta
105:
State-
COL-CONNECTED,
Eut-
Dial
Pad
(26),
Data-9
Co1
08:
State-
OUTPULSING.
Eut-
outpulse-digit,
Data=9
Co1
08:
State-
OUTPULSING,
Evt-
Digit
Sent,
Data-O
Co1
08:
State-
OUTPULSING,
Evt-
Digit
Sent,
Data-0
Sta
105:
State-
COL-CONNECTED,
Eut=
Dial
Pad
(26).
Data-9
Co1
08:
State-
TRLK.
Eut-
outpulse-digit,
Data-9
Co1 08:
State-
OUTPULSING.
Evt-
Digit
Sent,
Data-O
Sta
105:
State-
COL-CONNECTED,
Eut-
Dial
Pad
(26).
Data=8
Ccl
08:
State-
TALK,
Eut-
outpulse-digit.
Data-8
Co1
08:
Stats-
OLJTPULSING,
Evt-
Digit
Sent,
Data-O
Sta
105:
State-
COL,CONNECTED,
Eut-
Dial
Pad
(261,
Data-6
Co1
08:
State-
TALK,
Evt-
outpulse-digit,
Data-6
Co1
08:
State-
OUTPULSING.
Eut-
Digit
Sent,
Data-0
Sta
105:
State=
COL-CONNECTED,
Evt-
Dial
Pad
(26),
Data-6
Co1
08:
State-
TALK,
Eut-
outpulse-digit,
Data-6
Co1
08:
State=
OUTPUlSING.
Evt-
Digit
Sent,
Data-O
Sta
105:
State-
COL-CONNECTED,
Evt-
Dial
Pad
(261,
Data-5
Ccl
08:
State-
TALK,
Evt=
outpulse-digit,
Data-5
Co1
08:
State=
OUTPULSING.
Evt=
Digit
Sent,
Data-O
Figure
800-6 Event
Trace as it appears
on Display
F.
Morlifv
Memory command
H.
Exit the Monitor
mode
The Mod@
Memory
Command
is for Englneer-
ing Use only.
Use of this
command
can alter
or
damage
the
Infinite
4096
systems
operatfng
data base which
can result
in system malfunction.
If this occurs
it will be necessary
to power the sys-
tem
down
and
re-i.nitlalize
the data
base, then completely
re-program
the
customer
programming
data.
G.
Baud Rate Command
This co mmand
provides
a convenient
means
for changing
the baud
rate, for the RS232-C
port located
on the CPB, while in the Monitor
mode.
To change
the baud rate type 'B' plus
the desired
baud
rate, then the enter key.
NO'AT: AJer dunging the Baud Rate v&z Baud
Rate command. you must change your Baud
Rate on your Receiver/Termind
The Exit command
will terminate
the current
Remote
Monitor
enable/disable
session.
If
Event(s) Trace
have been or are still enabled
the event records
will be displayed
only after
exiting the MONitor
mode.
The J3xit command
format
is: MON X
Unless
instructed
by personnel
at a
Technical
Assistance
Center
(TAC) do
not leave the trace mode enabled
for
extended
periods
of time.
The system
will
"dump"
the
requested
event(s)
trace which
may use up paper
or f3ll
memory
buffers
on the
collecting
device.
It Is recommended
that
the
event traces
be disabled
(turned
of3
for all event(s) before leaving the sys-
tem site.
RfMLld
hnnc
1. Jan1raw
1992
Advertisement
Table of Contents
