Table of Contents
Advertisement
F.
G.
The
HearingAid
Compatibility
All In&&e
4096 Key Telephones
are Hear-
lng Aid Compatible.
as defined
in Section
68.3 16 of Part 68 FCC Rules and Regula-
UOXlS
OPX
CYrcuit
I@nfte
4096
Key Telephone
System may
be equipped
with single line OPX boards which
provide
four (4) 48 volt
FCC registered
2500-
type single line interface
ports.
l
Each OPX port when used to support
an
off-premise
extension
requires
an
OL 13C network
circuit.
l
An FCC registered
interface
such as a
W2 1X is also required
to connect
to the
public
network.
100.3
RECUUTORY
INFORMATION
CA-
HADIAN)
Depariment
of Communications
(DOC)
Won
Number:
676 2799A
Load Number:
19
Standard
Connector:
CA21A
Can-
Standards
Association
(CSAI
File Number:
LR!57228
A.
Notice
The Canadian
Department
of Communi-
cations'
label
identifies
certified
equip-
ment. Thfs
certification
means
that
the
equipment
meets certain
telecommunica-
tions network
protective.
operational
and
safety
requirements.
This
Department
does not
guarantee
the
equipment
will
operate
to the user's satisfaction.
Before
installing
this
equipment,
users
should
ensure
that It is permissible
to be
connected
to the factlitles
of the local tele-
communlcaUons
company.
The equip-
ment
must
also be installed
using
an
acceptable
method
of connection.
In some
cases, the company's
inside wiring
asso&
ated with single line individual
service may
be extended
by means
of a certified
con-
nector
assembly
(telephone
extension
cord).
The customer
should
be aware that
compliance
with the above condition
may
not prevent
degradation
of service in mrne
situations.
Repairs to cerUfled equipment should be
made by an
authorized
Canadian
matnte-
nance facility
designated
by the supplier.
Any repairs
or alterations
made
by the
user to this equipment.
or equipment
mai-
functtons.
may give the telecommunica-
tions
company
cause to request the user
to disconnect
the equipment.
Users should
ensure for their own protec-
tion that the electrical ground
connections
of the power
utility.
telephone
lines and
fnternd
metallic
water pipe system,
if pre-
Senk
are
connected
together.
This pre-
caution
may be particularly
important
in
rural areas.
I-4
Users
should
not attempt
to make
such
connections themselves, but
should
contact
the appropriate
elec-
tric inspection
authority.
or electri-
dan,
as appropriate.
B.
ErpladdonofLoadNumber
The
Load Number
(LN) assigned
to each
terminal
device denotes
the percentage
of
the total
load to be connected
to a tele-
phone loop which
is used by the device to
prevent
overloading.
The termination
on
a loop may consist
of any combination
of
devices
subject
only to the requirement
that the total of the load numbers
of all the
devices does not exceed 100.
C.
MaiJltenallcc L4.mitationB
Maintenance
on the In&&e
4096 Hybrid
Key Telephone
System is to be performed
only by the manufacturer
or its authorized
agent.
The
user
may
not
make
any
changes
and/or
repairs
except as sped-
tally noted
in this manual.
If unauthor-
ized alterations
or repairs
are made,
any
remalnlng
warranty
may be voided.
D.
Notice
of Compliance
The In&&e
4096
Hybrid
Key Telephone
System complies
with Class A or Class B
limits of the Canadian
Radio Interference
Regulations.
In accordance
with
FCC
Standard
15 (Subpart
J). the following
information
must be supplied
to the end
user:
loo-2
Issue 1, January
1992
Advertisement
Table of Contents
