Central Station Receiver 1 Format; Enter User Codes - NAPCO Gemini GEM-P1632 Programming Instructions Manual

Page 8
(Direct Entry)
Press to save. Press NEXT (
DATA CS RECEIVER 1 FORMAT
ENTRY
•(blank) Ademco Slow, Silent Knight Slow
2 Radionics Fast
3 Silent Knight Fast
4 Radionics, DCI, Franklin Slow
User# User Code
from left to right for each user code. Valid
spaces in between; leave blank (•) any trailing boxes. If "Enable Global Ambush Code" (Address 0720) is enabled and
"Global Ambush Code" (Address 1054) is
If the programmed code was less than 6 digits, press the
Level. Refer to the table below for the available area options.
USER OPTIONS
USER CODE AREA 1
OPTIONS
(UP TO 6 DIGITS)
AREA OPTIONS
Disabled User Code not active in this area.
Arm/Disarm Allows User Code to arm/disarm this area.
Arm Only Prevents User Code from disarming this area.
Service A Service Code has restricted arm/disarm rights; if an area is armed with a
Service Code, a "
on the GEM-RP2ASe2 keypad) and the area can be disarmed with any valid
User Code, including a Service Code. If the area is armed with OTHER than a
Service Code, it CANNOT be disarmed with a Service Code. This is typically
used to allow tradesmen access to premises under control of the owner.
Access This is normally used to activate a door striker while an area is disarmed.
Also program "Access Control on PGM2 Output" (Address 0719) and "PGM2
Output Access Control Timeout" (Address 0711).
* User Program User Program Option is enabled for Keypad 1 only, wherever it is connected
(Area 1 or Area 2). To enable User Program Option for any user add 8 to the
data entry for Area Option (see example). Then, User Programming can be
performed only at Keypad 1 by a user code with user program enabled.
lated User Options: "Enable Global Ambush Code" (Address 0720),
"Global Ambush Code" (Address 1054) & "Enable Managers Mode" (Address 0719).
CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above
and press to save. Similarly, to cancel a code, blank out each number of the code press
GEM-P1632 Programming Instructions

Central Station Receiver 1 Format


From the table below, enter the central station's receiver format. Use number

buttons
and press
) button to proceed.
DATA CS RECEIVER 1 FORMAT
ENTRY
5 Universal High Speed
B
C Ademco Point ID
E
Enter User Codes (Press the (
For default program, enter up to 32 User Codes, with Area 1 and Area 2
Options.
Press the (
Area 1 Area 2
the number buttons
digits. Enter up to 6 digits (4 digits is recommended) in the first six boxes
entries are: 0-9. NOTE: Press the
left blank(•), do not program the first two digits of ANY User Code as '99'.
USER AREA OPTIONS
AREA 2
DATA ENTRIES
OPTIONS
L
blank(•) blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
blank(•)
EXPLANATION

 
 
" appears on the GEM-RP1CAe2 keypad (a "

through . NOTE: Press the
for a blank space (•). Press
for letters B–E, respectively.
NOTE: Central Station Receiver 2 and 3 For-
mats can only be entered in Direct Address
SIA
Programming. See CS Receiver Options.
Pager
) button once to set the cursor to the User Code. Use
through
button once to set the cursor to the Area 1 Options
AREA OPTIONS: Up to 32 User Codes may
OPTION
be programmed.
ENABLED
R
Disabled
1 Arm/Disarm
2 Arm Only
3 Service
4 Access
Example: Program a code of "2222" for user 02, with
Add 8 * User Program
area 1 options of "Arm/Disarm" and "User Program".
Enter "2222" for a user code, "•(blank) 9" for area 1
options and "•(blank) •(blank)" for area 2 options.
For Area 2 Options, press the
button once again. Refer to the table



"
above for available options. NOTE: Press
the
Press
User Code, press the
the cursor to the User Number and change
it using the number buttons.
Program a new User Code as previously de-
R e -
scribed. Remember to record your user codes
in the Easy Menu Programming Worksheet at
the back of this manual.

button for a zero.
) button to set cursor.)

to enter a code of up to 6
button for a zero. No blank
Select the desired Area Options (Area 1
and Area 2) from the table shown and
enter in the remaining four boxes for
each user code.

for blank space (•).
to save. To proceed to the next
to save to save.
NAPCO Security Systems
WI897B 8/98
through
button to set