System Output Timeouts (Addr 0710, 0712-0714); Download/Callback Opt. (Addr 1183, 0236-0255); Pager Format Options (Addr 0256 & 0257) - NAPCO Gemini GEM-P1632 Programming Instructions Manual

WI897B 8/98
ADDRESS 0710
PGM2
Output
LEFT RIGHT
Timeout
(min.)
[Default = blank (•) blank (•) ]
DATA ENTRIES
DELAY/
LEFT RIGHT
TIMEOUT
blank (•) blank (•) 0 min.
blank (•) 1 1 min.
blank (•) 2 2 min.
blank (•) 3 3 min.
blank (•) 4
4 min.
blank (•) 5
5 min.
blank (•) 6
6 min.
1 blank (•)
16 min.
F F
255 min.
ADDRESS 1183
No. Rings
LEFT RIGHT
Before
Pickup
blank (•)
[Default = blank (•) blank (•)]
Callback
0236 0237 0238 0239 0240 0241 0242 0243 0244 0245 0246 0247 0248 0249 0250 0251 0252 0253 0254 0255
Telephone
Number
R
(Digits 1-20)
[Default = blank (•) for all digits 1-20]
CALLBACK TELEPHONE NUMBER: Enter telephone number to be used when downloading from a computer (see Glossary at the
back for more information).
1. Enter in right digit only (left digit is not used).
2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•).
3. Valid entries are: 1-9, B =
ADDRESS 0256
Leading Digits for
LEFT RIGHT
Pager Format
(1st Digit)
blank (•)
ADDRESS 0257
Leading Digits for
LEFT RIGHT
Pager Format
(2nd Digit)
blank (•)
[Default = blank (•) blank (•) for both]
NAPCO Security Systems
ADDRESS 0712
Alarm
Output
LEFT RIGHT
Timeout
(min.)
[Default = 1 blank (•)]
1. Select delay/timeout (0-255 min.) from the table shown.
2. Enter in corresponding address locations above (left and right digits).
3. For a desired delay/timeout not listed do the following:
A. Choose a desired delay/timeout, ex: 20 min.
B. Divide it by 16
OUTPUT TIMEOUTS: If a
the output will remain active (ON) until the system is reset or disarmed. For UL Residential
Installations, the minimum timeout is 4 minutes. For UL Commercial Installations, the minimum
NUMBER OF RINGS BEFORE PICKUP: Enter the number of rings before automatic pickup by the
control panel when downloading form a computer (see Glossary at the back for more information).
1. Enter in right digit only (left digit is not used).
2. Valid entries are: 1-9, 0 = 10, B = 11, C = 12, D = 13, E = 14, F = 15
NOTE: Default is 15 Rings. Dark shaded data shows option not available.
ADDRESS 0236-0255 (RIGHT DIGITS 1-20)
R R R R R R
button, C = button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with "00"..
However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows
you to program these digits to any number desired. Typical Pager report is "003 022 1234", where 3 is the Event,
22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as "98",
the Pager report will now appear as "983 022 1234". NOTE: See CS Receiver Options to select Pager Format.
1. Enter in 1st and 2nd Leading Digits in right digit only (left digit is not used) as shown.
2. Valid entries are: 0-9.
ADDRESS 0713
Pulse Alarm
Output
LEFT RIGHT
Timeout
(min.)
[Default = 1 blank (•)]
1 Quotient Left Digit
16 20
16
4 Remainder Right Digit
R R R R R R
GEM-P1632 Programming Instructions
ADDRESS 0714
PGM1
Output
LEFT
Timeout
(min.)
[Default = blank (•) blank (•)]
timeout of "0 min." is selected, then
R R R R R R
Page 23
RIGHT
R