Gem-Rp1Cae2 Keypad; Number Of Zones In Area 1; Panel Zone Doubling; Fire Zones In Area 1 - NAPCO Gemini GEM-P1632 Programming Instructions Manual

Page 6
A. GEM-RP1CAe2 Keypad


To create your customized default program using a GEM-RP1CAe2 keypad, enter the following parame-

   


 

 
    
 
  

   

ters and record your information on the Easy Menu Programming Worksheet (see page 43). In each of the



  
NEXT/YES
    following steps, press the
PRIOR/NO
  
AREA

  
   
( ) button to go backwards, the
R
(Direct Entry)
(after the first 8 zones), and will automatically round up to the next group of 4. For example, if you enter 18, it will
automatically convert this to 20 zones. Press
programming a 2 Area system, enter the total number of zones required for Areas 1 & 2. The Direct Address Program
Mode can then be used to remove zones from Area 1 and place them in Area 2. See Zone Options. If Programming a
Wireless Only system, or using wireless only on Zones 9-32, enter the total number of zones in system. Enter the
transmitter points in the RF Transmitter section of the Easy Menu Driven Programming Mode.
(Press YES or NO)
Diagram and Installation Instructions). If Panel Zone doubling is not desired, press NO (
(Direct Entry)
zones required for Areas 1 & 2. The Direct Address Program Mode can then be used to remove zones from Area 1 and
place them in Area 2. See Zone Options.
(Direct Entry)
been designated as Fire Zones may be programmed as 2 Wire Fire zones. Press NEXT (
NOTE: JP3 must be set to "2-WF" position for 2-wire fire zones (refer to Installation Instructions).
(Press YES or NO)
GEM-P1632 Programming Instructions
button to set cursor, the NEXT (
button to save and the
Total Number of Zones in Area 1 (Appears for New Panel Only)

Directly enter the total number of zones to be programmed for Area 1. Valid
entries are from 01 to 32. Directly enter the total number of zones, including
leading zeros. Use number buttons
button for a zero. The system is based on groups of 4 zones each
to save. Press NEXT (
Panel Zone Doubling (Appears for New Panel Only)
If you wish to double the number of hardwired zones within the panel from 8
to 16, press the YES (
zones, but will be designated for Normally Closed devices only. The terminal
for Zone 1 will now support both Zones 1 and 9 with the use of the supplied
TM
EZ Zone Doubling resistors, E (2.2K) & Z (3.9K) supplied. (Refer to Wiring
Fire Zones in Area 1 (Appears for New Panel Only)
Enter the number of any zones which are to be used as Fire Zones (both
2-wire, 4-wire or wireless). Valid entries are from 01 to 32. Directly enter
each zone number, including leading zeros, and press
repeat for any additional zone(s). Press NEXT (
NOTE: If you are programming a 2 Area system, enter the total number of
2-Wire Fire Zones in Area 1 (Appears for New Panel Only)
Enter the number of any Fire Zones (from previous question) which are to be
used with 2-wire smoke detectors. The only valid entries are 07 and 08.
Directly enter each zone number, including leading zeros. Press
and then repeat for any additional zone(s). NOTE: Only zones which have

Local or Central Station Reporting System (Appears for New Panel Only)
Press YES ( ) button for all zones to report; press NO (
for no zones to report (LOCAL SYSTEM).



) button to go forwards, the PRIOR
button twice to exit at any time.

through
) button to proceed. NOTE: If you are

) button. The 16 zones will no longer be EOL



NAPCO Security Systems
WI897B 8/98
. NOTE: Press the
).
to save, and then
) button to proceed.
to save,
) button to proceed.
) button