Key Fob Transmitters; Enter Zone Descriptions; Dealer Code - NAPCO Gemini GEM-P1632 Programming Instructions Manual

Page 10
KF Area Xmitter
# ID
DATA AUX 1/AUX 2 DATA
ENTRY OPTIONS ENTRY
•(blank) None 7
8
1 Relay Group 1
9
2 Relay Group 2
0
3 Relay Group 3
B
4 Relay Group 4
5 Relay Group 5 C
6 Relay Group 6
Note: If the Key Fob is converted for Two Button "Emergency Use" (by cutting an internal jumper), both top or bottom
buttons must be depressed to activate an alarms. In this case, the Aux-1 and Aux-2 cannot be programmed.
Press to save. Press NEXT (
Key Fob Zone Assignment (refer to display as shown on the previous page: press the (
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off button = point 2; A1 = point
3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using 2 buttons) or 8 key fobs (using all 4 buttons) or any
combination up to a maximum of 32 controlled zones can be assigned, providing multiple wireless panic buttons on a
system, each reporting to the Central Station or a pager and/or annunciating on a keypad the key fob zone number with
description/location. To assign a key fob to a zone: program the keyfob as you would a transmitter, entering the keyfob's
ID code, check sum and point number at the appropriate zone. The "Quick Method" is not allowed. The zone may be
hardwired to a sensor as well as assigned to a key fob (either one will activate the zone alarm output). NOTE: If assigning
a key fob to a zone, the "ON/OFF" buttons on the key fob will no longer arm/disarm the system. The key fob is converted
to a "panic only" device.

Enter Zone Descriptions

(Direct Entry)
new description as above.
NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader
Software. See Easy Menu Programming Worksheet (page 45) for available zone description characters.
(Direct Entry)
(Direct Entry)
EXIT DEALER PROGRAM MODE: This completes the custom default program. Press the


Direct Address Program Mode for further programming or press the
resume normal keypad operation.
CLEAR PROGRAM: Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode,
press the button to enter the Address Program Mode; (b) access Location 1197 (Clear Program); (c) press
start over.
GEM-P1632 Programming Instructions
Key Fob Transmitters (Press the (
Keyfobs can be programmed as "Arm/Disarm" devices using their buttons
(refer to WI752). For each Key Fob Transmitter, enter:
the Key Fob Transmitter number (01–08).
Check Aux
Sum 1&2
area number to which transmitter is assigned (1 or 2); enter 0 to disable
keyfob.
AUX 1/AUX 2 OP-
TIONS
the 6-digit RF ID # printed on the transmitter (enter all numbers and/or
Relay Group 7
letters, including leading "0"s, if any).
Relay Group 8
1-digit checksum number printed on the transmitter (enter all numbers
Keypad Panic
and/or letters, including leading "0"s, if any).
Aux K.P. Panic
Instant
Aux-1 Option (see key fob aux 1 & aux 2 options).
Toggle Aux Relay

Aux-2 Option (see key fob aux 1 & aux 2 options).
) button to proceed.

Press the
and
tion of up to two lines. Press
next description, place the cursor under the Zone Number (e.g. "01") and
change the Zone Number using the

Dealer Code

Directly enter the Dealer Code (default = 456789), including leading zeros.
Use the
zero. Press
Re-enter the Dealer Code to verify the previous code. Press
Press NEXT (

and buttons to place the cursor; press the

buttons to select the character. For each zone, enter a descrip-
to save each description. To proceed to the
through buttons. NOTE: Pres the
to save.

) button to proceed.


button once again to end all programming and
WI897B 8/98
) button to set cursor.)
) button to go backwards.)

and buttons. Program a

button for a
to save.


button to enter the
NAPCO Security Systems

and