Gem-Rp3Dgtl/Gem-K3Dgtl And Gem-Rp4Rfc/Gem-K4Rf Keypad - NAPCO GEMINI GEM-P1632 Programming Instructions Manual

WI1148B 10/06
GEM-RP3DGTL/GEM-K3DGTL and GEM-RP4RFC/GEM-K4RF Keypad Easy Program Menu
Enter the Default Dealer Program Code ("456789") for a new panel or enter your custom Dealer Program Code if
GEMINI
SYSTEM ARMED
programmed. Press
1 7
ENT A1
01/01/97 12:00AM
INT ERIOR B YPAS S F IRE/T BL SY S T BL CHIM E
NEXT/YES
A 1 2 3 E
D ). Press [NEXT] to enter Dealer Program Mode. For the GEM-RP3DGTL/GEM-K3DGTL (and GEM-RP4RFC/GEM-
B
PRIOR/NO
B 4 5 6 F
AREA
C 7 8 9 0 G
K4RF), questions are in the form of a 2-digit number flashing in the display. Press
COMPUTERIZED SECURITY SYSTEM
R
to answer the question. Press
review your Easy Program Mode responses (before pressing
play again. If the data is correct, press
your data. Note: Review your Easy Program Mode responses after the initial programming of the control, except for questions marked "For
New Panel Only". These questions set up the basic structure of the panel program ("Number of Zones in an Area", etc.) and cannot be
viewed or altered once set. To exit the Dealer Program Mode, press
Flashing
01
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
03
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
04
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
05
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
06
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Press YES or NO)
07
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
H
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
L
NAPCO Security Systems
, followed by [PRIOR/NO] repeatedly until "17" is displayed (you can scroll back by pressing
R
again to scroll through each segment. Press [NEXT] to go to the next question. To
R
U
to save), press
U
to save. If the data is incorrect, press
to the factory default, enter the Direct Address Program Mode, go to location 2286 and press
Total Number of Zones (Appears for New Panel Only)
Directly enter the total number of zones to be programmed. Valid entries are from 01 to 32. Directly
enter the total number of zones, including leading zeros. Use number buttons
NOTE: Press the button for a zero. The system is based on groups of 4 zones each (after the
0
first 8 zones), and will automatically round up to the next group of 4. For example, if you enter 13, it
will automatically convert this to 16 zones. Press
proceed.
Panel Zone Doubling (New Program Only)
•
To double the number of hardwired panel zones from 8 to 16, press the NEXT/YES button.
•
If Panel Zone doubling is not desired, press the PRIOR/NO button.
•
The 16 zones will remain EOL terminated zones, requiring Normally Closed devices only.
•
Refer to Wiring Diagram and Installation Instructions for wiring instructions
Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (both 2-wire, 4-wire or wireless). Valid entries are from 01
to 32. Directly enter each zone number, including leading zeros, and press
repeat for any additional zone(s). Press the NEXT/YES button to proceed.
NOTE: If you are programming a multiple Area system, enter the zone number of zones required for
Areas 1 & 2. The Direct Address Program Mode can then be used to remove zones from Area 1 and
place them in Area 2. See Zone Options.
2-Wire Fire Zones (Appears for New Panel Only)
Enter the zone number of any Fire Zones (from previous question) which are to be used with 2-wire
smoke detectors. The only valid entries are 07 and 08. Directly enter each zone number, including
U
leading zeros. Press to save, and then repeat for any additional zone. NOTE: Only zones which
have been designated as Fire Zones can be programmed as 2 Wire Fire zones. Press the NEXT/
YES button to proceed. NOTE: JP7 must be set to "2-WF" position for 2-wire fire zones 7 and 8 (refer
to Installation Instructions).
Local System or C.S. Reporting System (Appears for New Panel Only)
Press the NEXT/YES button for all zones to report; press the PRIOR/NO button for no zones to report
(LOCAL SYSTEM).
Exit/Entry Zones (Appears for New Panel Only)
Directly enter the zone numbers which are to be used as Exit/Entry zones. Valid entries are from 01
to 32. Directly enter each zone number, including leading zeros. Use number buttons
. NOTE: Press the
9
additional zone(s). Press the NEXT/YES button to proceed.
NOTE: Exit/Entry Zones will have an entry delay of 30 seconds and an exit delay of 60 seconds.
until the 2-digit question number flashes in the dis-
R
to set the cursor into the next field and again enter
R
twice to resume normal keypad operation. To return the panel
C
U
to save. Press the NEXT/YES button to
button for a zero. Press
0
X
GEM-P1632 Programming Instructions
to set the cursor into the next field
R
through
1
U
to save, and then
1
U
to save and then repeat for any
Page 13
U
.
.
9
through