System Output Timeouts; Download/Callback Options; Pager Format Options - NAPCO GEMINI GEM-P1632 Programming Instructions Manual

WI1148B 10/06
SYSTEM OUTPU T TI ME OUTS (AD DRESS 14 12 & 14 14 -14 16)
ADDRESS 1412
PGM2
Output
LEFT RIGHT
Timeout (min.)
[Default = blank (•) blank (•)]
DATA ENTRIES DELAY/
TIMEOUT
LEFT RIGHT
blank (•) blank (•) 0 min.
blank (•) 1 1 min.
blank (•) 2 2 min.
blank (•) 3 3 min.
blank (•) 4 4 min.
blank (•) 5 5 min.
blank (•) 6 6 min.
1 blank (•) 16 min.
F F 255 min.
DOWNL OAD /C ALLBA CK OP TI ONS (ADDRESS 2059 & 0526-0545)
ADDRESS 2059
No. Rings
Before
LEFT RIGHT
Pickup blank (•)
[Default = blank (•) blank (•)]
CALLBACK
Telephone 0526 0527 0528 0529 0530 0531 0532 0533 0534 0535 0536 0537 0538 0539 0540 0541 0542 0543 0544 0545
Number R R R
(Digits 1-20)
[Default = blank (•) for all digits 1-20]
CALLBACK TELEPHONE NUMBER: Enter telephone number to be used when downloading from a computer (see installation
instructions WI808 for more information).
1. Enter in right digit only (left digit is not used).
2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•). For a zero, press
3. Valid entries are: 1-9, B =
U
4. Press to save.
PAGER FOR MAT OP TION S (ADD RESS 054 6 & 05 47)
ADDRESS 0546
Leading Digits for
Pager Format
LEFT RIGHT
(1st Digit) blank (•)
ADDRESS 0547
Leading Digits for
Pager Format
LEFT RIGHT
(2nd Digit) blank (•)
[Default = blank (•) blank (•)]
L
NAPCO Security Systems
ADDRESS 1414
Alarm
Output
LEFT RIGHT
Timeout (min.)
[Default = 15 mins. = (blank) F]
1. Select delay/timeout (0-255 min.) from the table shown.
2. Enter in corresponding address locations above (left and right digits).
3. For a desired delay/timeout not listed do the following:
A. Choose a desired delay/timeout, ex: 20 min.
B. Divide it by 16
U
4. Press to save.
OUTPUT TIMEOUTS: If a timeout of "0 min." is selected, then the output will remain active (ON)
until the system is reset or disarmed. For UL Residential Installations, the minimum timeout is 4
minutes. Not UL listed for Commercial Installations.
NUMBER OF RINGS BEFORE PICKUP: Enter the number of rings before automatic pickup by the control
panel when downloading from a computer (see installation instructions WI808 for more information).
1. Enter in right digit only (left digit is not used).
2. Valid entries are: 3-9, 0 = 10, B = 11, C = 12, D = 13, E = 14, F = 15
NOTE: Default is 15 Rings. Dark shaded data shows option not available.
U
3. Press to save.
ADDRESS 0526-0545 (RIGHT DIGITS 1-20)
R R R R R R
* #
button, C = button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location.
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with "00".
However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows
you to program these digits to any number desired. A typical Pager report is "003 22 1234", where 3 is the Event,
22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as "98",
the Pager report will now appear as "983 22 1234". NOTE: See CS Receiver Options to select Pager Format.
1. Enter in 1st and 2nd Leading Digits in right digit only (left digit is not used) as shown.
2. Valid entries are: 0-9.
U
3. Press to save.
ADDRESS 1415
Pulse Alarm
Output
LEFT
Timeout (min.)
[Default = 15 mins. = (blank) F]
1 Quotient
16 20
16
4 Remainder
R R R R R R
X
GEM-P1632 Programming Instructions
ADDRESS 1416
PGM1
Output
RIGHT
Timeout (min.)
[Default = blank (•) blank (•)]
Left Digit
Right Digit
R R R R R
G0
Page 25
LEFT RIGHT
.