Table of Contents
Advertisement
[ENCRYPTION]
[DEFAULT KEY]
[KEY1] - [KEY4]
[KEY]
[EAP]
[USER NAME]
[PASSWORD]
Note
f Contact the manufacturer of the access point (radio repeating device) in use if wireless LAN connection cannot be established via the
access point even after "Setting for projector" (x page 102) is executed.
f If you use EAP, settings of the projector need to be configured according to the RADIUS server settings. Consult your network administrator
for the RADIUS server settings.
f If you use EAP in combination with an access point where SSID broadcast is disabled, select [WPA-EAP] or [WPA2-EAP] for authentication
method even when the authentication of the access point is WPA-EAP/WPA2-EAP.
7)
Press as to select [STORE], and press the <ENTER> button.
f Press as to select [RETURN] and then press the <ENTER> button to return to the [WIRELESS LAN]
([USER1], [USER2], or [USER3]) screen (1/2).
8)
When the confirmation screen is displayed, press qw to select [OK], and press the <ENTER> button.
Note
f The following settings are configured for [USER1], [USER2], and [USER3] as the factory default.
[DHCP]
[IP ADDRESS]
[SUBNET MASK]
[DEFAULT GATEWAY]
[DNS1]/[DNS2]
[SSID]
[AUTHENTICATION]
[ENCRYPTION]
Changing the [USER1]/[USER2]/[USER3] name
1)
Press as to select [WIRELESS LAN].
80 - ENGLISH
Chapter 4 Settings — [NETWORK] menu
Select the encryption method used for the communication between the projector and the network.
[NONE]
[WEP]
[TKIP]
[AES]
Set a number from 1 to 4 for the default key.
It can be selected only when [AUTHENTICATION] is set to [OPEN] or [SHARED], and the encryption
method is [WEP].
Set WEP key to the key number selected in [DEFAULT KEY].
It can be selected only when [AUTHENTICATION] is set to [OPEN] or [SHARED], and the encryption
method is [WEP].
You can set a 64-bit or 128-bit WEP key. Enter five single-byte alphanumeric characters (10 digits for
hexadecimal) for 64-bit, or enter 13 single-byte alphanumeric characters (26 digits for hexadecimal)
for 128-bit.
Set the key.
It can be selected when [AUTHENTICATION] is set to [WPA-PSK] or [WPA2-PSK].
Enter 8 to 63 alphanumeric characters or 64-digit hexadecimal.
Select the EAP set for RADIUS server.
It can be selected when [AUTHENTICATION] is set to [WPA-EAP/WPA2-EAP], [WPA-EAP], or
[WPA2-EAP]. The types of EAP that can be selected are as follows.
[PEAP(MS-CHAPv2)], [PEAP(GTC)], [EAP-TTLS(MD5)], [EAP-TTLS(MS-CHAPv2)], [EAP-FAST(MS-
CHAPv2)], [EAP-FAST(GTC)]
Enter the user name to be used for authentication in single-byte alphanumeric characters (space not
included, 64 characters at the maximum).
It can be selected when [AUTHENTICATION] is set to [WPA-EAP/WPA2-EAP], [WPA-EAP], or
[WPA2-EAP].
Enter the password to be used for authentication in single-byte alphanumeric characters (64
characters at the maximum).
It can be selected when [AUTHENTICATION] is set to [WPA-EAP/WPA2-EAP], [WPA-EAP], or
[WPA2-EAP].
OFF
192.168.11.100
255.255.255.0
192.168.11.1
(Blank)
Panasonic Projector
Open
None
Select this item not to use encryption.
It can be selected only when [AUTHENTICATION] is set to [OPEN]
or [SHARED].
Select this item when the encryption method is WEP.
Select this item when the encryption method is TKIP.
It can be selected only when [AUTHENTICATION] is set to [WPA-
PSK], [WPA2-PSK], [WPA-EAP], or [WPA2-EAP].
Select this item when you use AES for the encryption method.
It can be selected only when [AUTHENTICATION] is set to [WPA-
PSK], [WPA2-PSK], [WPA-EAP], or [WPA2-EAP].
Advertisement
Table of Contents
