Set Event Timers - American Dynamics AD2052 System Programming Manual

MENU PROGRAMMING

SET EVENT TIMERS

Event Timers permits automatic callup of System Tours and/or
Alarm Monitor/Contact Tables. Each one of the automatic
callups is referred to as an Event.
The EVENT TIMER menu is used to identify each Event and
to program each Event for automatic callups. A maximum of
35 Events are available for programming. Each Event can be
programmed for individual System Tour and Alarm
Monitor/Contact Table callups on different days of the week.
E V E N T T I M E R
0 7 : 11 D I S A B L E D
E D I T T I M E R
N E X T T I M E R
C L E A R T I M E R
E N A B L E T I M E R
C H A N G E T I M E R TO H H : M M
P R E V I O U S M E N U
An Event Timer ("Event") is created by entering a new time in
the first line of this menu. If the Event is a new time the word
"NEW" is displayed. If the Event already exists, either the
word "ENABLED" or "DISABLED" is displayed. If the timer
is cleared, the words "ILLEGAL TIME" are displayed.
To create a new Event Timer, or edit an existing Timer:
1. Move the cursor to the time location under the menu title.
2. Enter the hours (for example, 07).
3. Press the ACK key.
4. Enter the minutes (for example, 11).
5. Press the ACK key. This moves the cursor to the EDIT
TIMER line item in the EVENT TIMER menu.
Note: A maximum of 35 Event Timers can be programmed.
If a time is entered for a 36th event, the message "EVENT
TABLE FULL" is displayed. An existing Event Timer
can be cleared to make room for a newly created table (see
CLEAR TIMER menu command, page 4-11).
S Y S T E M
1 S E T T I M E A N D D AT E
2 S E T S Y S T E M TO U R S
3 S E T S Y S T E M S A LV O S
4 S E T E V E N T T I M E R S
5 S E T A L A R M C O N TA C T S
6 M O N I TO R S TAT U S
R E T U R N M A I N
EDIT TIMER
Place the cursor on the EDIT TIMER line and press the ACK
key to display the SET EVENT TIMERS menu.
This menu programs System Tours and Alarm Monitor/Contact
(ALM) Table callups. The menu has multiple pages with eight
monitors per page. See page 4-3 for cursor movement
instructions.
M O N
0 0 1
0 0 2
0 0 3
0 0 4
0 0 5
0 0 6
0 0 7
0 0 8
A L M
Note: The day of the week must be set properly for Events to
occur as desired. See page 4-4 to set day of the week.
System Tour callup
Each entry in this table identifies a System Tour that is called
at the specified Event time for the indicated monitor (MON) on
the indicated day of the week. The entries for a new Event
Timer are defaulted to 0, no System Tours called to monitors.
To program a System Tour for callup by an Event Timer:
1. Move the cursor to the desired day of week and MON
(monitor) position.
2. Enter the System Tour number to call to this monitor.
3. Press the ACK key.
Note: Entering 00 is a "no-action" command while 65 is a
"hold monitor at current camera" command.
4-10
S E T E V E N T T I M E R S
T I M E - 0 7 : 11
D AY O F W E E K
S M T W
0 1 0 2 0 3 0 4
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 1 0 0
P R E V I O U S M E N U
T F S
0 5 0 6 0 7
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0