Toro Pro Sneak 365 Operator's Manual page 5

•
Do not operate on wet grass. Reduced traction could
cause sliding.
•
Do not park the machine on a hillside or slope without
lowering the attachment to the ground, setting the parking
brake, and chocking the wheels.
•
Only operate the machine on level ground when the
machine is in the narrow wheel configuration.
Rollover Protection Structure (ROPS)
System
•
Before operating a machine with a ROPS (rollover
protection structure), ensure that the seat belt is in good
condition and is securely attached to the machine.
•
Always wear a seat belt when operating a machine with
a ROPS.
•
Inspect the ROPS at the interval recommended in this
manual or when the ROPS has been in an accident.
•
Repair a damaged ROPS using only genuine Toro
replacement parts; do not repair or modify the ROPS.
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before driving under any
objects and do not contact them.
•
Do not remove the ROPS except when servicing or
replacing it.
•
Do not add weight to the machine that exceeds the gross
weight displayed on the ROPS label.
Maintenance and Storage
•
Disengage the auxiliary hydraulics, lower the attachment,
set the parking brake, stop the engine, and remove the
key. Wait for all movement to stop before adjusting,
cleaning, or repairing.
•
Clean debris from attachments, drives, mufflers, and
engine to help prevent fires. Clean up oil or fuel spillage.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery before making any repairs.
Disconnect the negative terminal first and the positive
last. Reconnect positive first and negative last.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Charge batteries in an open well ventilated area, away
from spark and flames. Unplug the charger before
connecting or disconnecting it from the battery. Wear
protective clothing and use insulated tools.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
•
Keep nuts and bolts tight. Keep equipment in good
condition.
•
Never tamper with safety devices.
•
Keep the machine free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow the machine
to cool before storing.
•
Use extra care when handling fuels. They are flammable
and vapors are explosive.
– Use only an approved container.
– Never remove the fuel cap or add fuel when the
engine is running. Allow the engine to cool before
refueling. Do not smoke.
– Never refuel the machine indoors.
– Never store the machine or fuel container inside
where there is an open flame, such as near a water
heater or furnace.
– Never fill a container while it is inside a vehicle, trunk,
pick-up bed, or any surface other than the ground.
– Keep container nozzle in contact with the tank during
filling.
•
Stop and inspect the equipment if you strike an object.
Make any necessary repairs before restarting.
•
Use only genuine Toro replacement parts to ensure that
original standards are maintained.
•
Battery acid is poisonous and can cause burns. Avoid
contact with skin, eyes, and clothing. Protect your face,
eyes, and clothing when working with a battery.
•
Battery gases can explode. Keep cigarettes, sparks and
flames away from the battery.
•
Keep your body and hands away from pin hole leaks
or nozzles that eject high pressure hydraulic fluid. Use
cardboard or paper to find hydraulic leaks; never use
your hands. Hydraulic fluid escaping under pressure can
penetrate skin and cause injury requiring surgery within a
few hours by a qualified surgeon or gangrene may result.
5