Download
Share
Print this page
Toro Pro Sneak 360 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. Pro Sneak 360
  6. Operator's manual

Toro Pro Sneak 360 Operator's Manual

Hide thumbs Also See for Pro Sneak 360:

Advertisement

Quick Links

Download this manual
Hydra Borer
Pro Sneak 360 or 365 Vibratory Plow
Model No. 25418
Model No. 25418E
Model No. 25421
Model No. 25421E
This product contains a chemical or chemicals known to the State of California to
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.
1. Decal125-8488 (ProSneak 360)
2. Decal 125-6671
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
WARNING
CALIFORNIA
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Register at www.Toro.com.
Figure 1
3. Decal 125-6681
4. Decal 125-8488 (ProSneak 365)
Original Instructions (EN)
Form No. 3389-762 Rev A
Operator's Manual
All Rights Reserved *3389-762* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro Pro Sneak 360

Summary of Contents for Toro Pro Sneak 360

  • Page 1 Form No. 3389-762 Rev A Hydra Borer Pro Sneak 360 or 365 Vibratory Plow Model No. 25418 Model No. 25418E Model No. 25421 Model No. 25421E Operator's Manual WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
  • Page 2 125-6671 1. Explosion hazard; electric shock hazard—call local utilities before digging. 125–6681 1. Entanglement hazard—keep away from moving parts; keep all guards in place. 125–8488 1. Turn clockwise 3. Turn counterclockwise 2. Stop rotation...
  • Page 3 Install the control valve and handle (Pro Straight fitting Sneak 365). Bolt (1 1/4 inch) Handle assembly Hose, 114.3 cm (45 inches) Hose, 91.44 cm (36 inches) Install the hoses (Pro Sneak 360). Hose, 37.44 cm (14 3/4 inches) Hose connector...
  • Page 4 Procedure Description Qty. Hose, 51 cm (20 inches) Hose, 95 cm (38 inches) Hydraulic tube 90 degree adapter fitting Install the hoses (Pro Sneak 365). 45 degree adapter fitting R-clamps Bolts Nuts – No parts required Test the installation. Installing the Hydra Borer Motor Parts needed for this procedure: Motor...
  • Page 5 g021923 Figure 5 g021920 10. Torque the bolts to 91 to 113 N-m (67 to 83 ft-lb). Figure 3 11. Install the joint assembly to the motor assembly. Secure with the bolt (3/8 inch) and the nut (3/8 x 2-1/2 inch) 6.
  • Page 6 Procedure 1. Install the fittings as shown in Figure Installing the Control Valve and Handle (Pro Sneak 360) Parts needed for this procedure: g021925 Figure 7 Bracket Control valve 2. Torque the fittings to 104 to 127 N-m (77 to 94 ft-lb).
  • Page 7 Installing the Control Valve and Handle (Pro Sneak 365) Parts needed for this procedure: Bracket Control valve 45-degree, elbow fitting Straight fitting Bolt (1 1/4 inch) g021927 Handle assembly Figure 9 1. Bolt (2-1/4 inch) 4. Bracket Procedure 2. Bolt (2-1/2 inch) 5.
  • Page 8 Installing the Hoses (Pro Sneak 360) Parts needed for this procedure: Hose, 114.3 cm (45 inches) Hose, 91.44 cm (36 inches) Hose, 37.44 cm (14 3/4 inches) g025905 Hose connector Figure 12 1. 45-degree fitting (2) 2. Straight fitting (3)
  • Page 9 1. Disconnect hose A from the hydraulic pump (Figure 16), add the hose connector, and connect hose B to the other end of the connector (Figure 17). g021980 Figure 15 g021983 1. Port A on the motor 3. Port A on the hydra-borer-control valve 2.
  • Page 10 Installing the Hoses on a Machine with 5. Route hose C (36 inches) from the straight fitting (In Port) on the hydra-borer control valve (Figure 14) to the Trencher Attachment Installed the hose connector on hose D (Figure 21). Use this procedure if you have a machine that has a trencher attached.
  • Page 11 1. Connect the 2 45-degree adapter fittings onto the middle port of the control valve (Figure 22); torque to 81 N-m (60 ft-lb). g025907 Figure 22 1. Hydra-borer motor 4. Nut 2. Bolt 5. 45-degree adapter fittings 3. R-clamp 6. Hydra-borer-control valve 2.
  • Page 12 Installing the Hoses on a Machine with the Trencher Attachment Installed Use this procedure if you have a machine that has a trencher attached. If you have a machine that does not have a trencher attached, go to Installing the Hoses on a Machine without the Trencher Attachment Installed (page 11).

  • Page 13: Operation

    Boring the Hole Important: Boring is a two person operation. Do not attempt to perform this operation by yourself. 1. Position the machine with the drive head at the Testing the Installation beginning of the trench and lower it to the appropriate depth.
  • Page 14 rate. Do not push or pull the bit through the soil 6. When a rod coupling is about 15 cm (6 inches) into the when the drive head is not turning. entrance trench or when the reamer completely enters the trench with about 15 cm (6 inches) of the cable or 13.
  • Page 15 Storage 1. Before long term storage, wash the attachment with mild detergent and water to remove dirt and grime. 2. Check the condition of the hydraulic hoses. Replace any damaged hoses. 3. Ensure that all hydraulic couplers are connected together to prevent contamination of the hydraulic system.

  • Page 16: Troubleshooting

    Troubleshooting Problem Possible Cause Corrective Action The bore drive head does not rotate. 1. The hydraulic coupler is not completely 1. Check and tighten all couplers. connected. 2. A hydraulic coupler is damaged. 2. Check the couplers and replace any that are damaged.

This manual is also suitable for:

Pro sneak 3652541825418e2542125421e