Toro Pro Sneak 365 Operator's Manual page 4

– Never refuel or drain the machine indoors.
– Know the hand signals used on your job. Follow the
instructions of the flagmen, signals, etc.
•
Check that the operator's presence controls, safety
switches, and shields are attached and functioning
properly. Do not operate unless they are functioning
properly.
Operation
•
Before digging, have the area marked for
underground utilities, and do not dig in marked
areas.
•
Never run an engine in an enclosed area.
•
Before starting each day, check the machine for oil or fluid
leaks. Replace all damaged, loose, worn or missing parts
and follow the lubrication and maintenance procedures
shown in this manual.
•
Only operate in good light, keeping away from holes and
hidden hazards.
•
Be sure all drives are in neutral and parking brake is
engaged before starting the engine. Only start the engine
from the operator's position.
•
Slow down and use extra care on hillsides. Ground
conditions may adversely affect the stability of the
machine. Use caution when working on newly disturbed
earth.
•
Allow adequate space when turning this unit.
•
Slow down and use caution when making turns and when
changing directions on slopes.
•
Never operate without the guards securely in place. Be
sure all interlocks are attached, adjusted properly, and
functioning property.
•
Stop on level ground, lower implements, disengage the
auxiliary hydraulics, engage parking brake, and shut off
the engine before leaving the operator's position for any
reason.
•
Keep hands and feet away from moving attachments.
•
Look behind and down before backing up to be sure of
a clear path.
•
Never carry passengers and keep pets and bystanders
away.
•
Slow down and use caution when making turns and
crossing roads and sidewalks.
•
Do not operate the machine under the influence of
alcohol or drugs.
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Use care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
•
Read all attachment manuals.
•
Ensure that the area is clear of other people before
operating the machine. Stop the machine if anyone enters
the area.
•
Never leave a running machine unattended. Always stop
the engine, set the parking brake, and remove the key
before leaving.
•
Never jerk the controls; use a steady motion.
•
Watch for traffic when operating near or crossing
roadways.
•
Do not touch parts which may be hot from operation.
Allow them to cool before attempting to maintain, adjust,
or service.
•
Check for overhead clearances (i.e. branches, doorways,
electrical wires) before driving under any objects and do
not contact them.
•
Ensure that you operate the machine in areas where
there are no obstacles in close proximity to the operator.
Failure to maintain adequate distance from trees, walls,
and other barriers may result in injury as the machine
backs up during operation if the operator is not attentive
to the surroundings. Only operate the unit in areas where
there is sufficient clearance for the operator to safely
maneuver the product.
•
Never allow anyone in the trench while operating the
machine.
•
Locate the pinch point areas marked on the machine and
attachments and keep hands and feet away from these
areas.
•
Before operating the machine with an attachment, ensure
that the attachment is properly installed.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Slope Operation
Slopes are a major factor related to loss-of-control and
tip-over accidents, which can result in severe injury or death.
All slopes require extra caution.
•
Avoid operating this machine on slopes.
•
Remove obstacles such as rocks, tree limbs, etc. from the
work area. Watch for holes, ruts, or bumps, as uneven
terrain could overturn the machine. Tall grass can hide
obstacles.
•
Use only Toro-approved attachments. Attachments can
change the stability and the operating characteristics
of the machine. Warranty may be voided if used with
unapproved attachments.
•
Keep all movements on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Avoid starting or stopping on a slope. If the machine
loses traction, proceed gradually, straight down the slope.
•
Avoid turning on slopes. If you must turn, turn slowly
and keep the heavy end of the machine uphill.
•
Do not operate near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.
4