Extron electronics IPL T S Series User Manual page 43

Command ASCII (Telnet)
(Host to Unit)
Web Browser-specific
Read response from E }
UB
last URL command
IP Setup Commands
Set unit name
24
E X1@ }
CN
Set unit name to factory E }
•CN
default 24
View unit name
E }
CN
Set date/time
24
E X1# }
CT
View date/time E }
CT
Set GMT offset
E X# }
CZ
View GMT offset E }
CZ
Set daylight savings
E X3$ }
CX
time
24
View daylight savings
E }
CX
time
Set DHCP on E }
24 E1DH
Set DHCP off 24
E }
0 DH
NOTE: Changing DHCP from on to off also resets the IP address to the factory default (192.168.254.254).
View DHCP mode
E }
DH
Set IP address
24
E X1$ }
CI
View IP address E }
CI
View hardware address
E }
CH
(MAC)
Set subnet mask E X1( }
24 CS
View subnet mask
E }
CS
KEY:
X#
= Greenwich Mean Time (GMT) offset value — (-
The leading zero is optional, for example,
X%
= On or off status — 0 = off or disable (default for DHCP), 1 = on or enable
X1@
= E-mail domain name, for example, extron.com
X1#
= An e-mail account username (for SMTP authentication) of up to 31 characters. Do not use commas. This parameter is optional during setup.
X1$
xxx.xxx.xxx.xxx
= IP address (
X1*
xx-xx-xx-xx-xx-xx
= Hardware (MAC) address (
X1(
xxx.xxx.xxx.xxx
= Subnet mask (
X3$
= An e-mail account password (for SMTP authentication) of up to 31 characters. Do not use commas. This parameter is optional during setup. In a response, instead of the actual password,
X4(
= Default name: a combination of the model-name and the last 3 pairs of the MAC address (that is, IPL-T-S2-00-02-3D)
URL Encoded (Web)
Host to Unit)
|
WUB
X1@ |
W CN
|
W%20CN
|
WCN
X1# |
W CT
|
WCT
X# |
W CZ
|
WCZ
X3$ |
W CX
|
WCX
|
W1DH
|
W0DH
|
WDH
X1$ |
W CI
|
W CI
|
WCH
X1( |
W CS
|
WCS
12.00 14.00
to + ) represents the time difference in hours and minutes (+/-hh — mm) relative to Greenwich, England.
5 — 30 05 — 3
= 0. Do not use a plus (+) sign if the GMT offset is positive.
) — Leading zeros in each of the four fields are optional in setting values, and they are suppressed in returned values.
).
). Leading zeros in each of four fields are optional in setting values and are suppressed in returned values.
Response Additional Description
(Unit to Host)
]
response from command
X1@]
Ipn•
X4(]
Ipn•
X1@]
X1#]
Ipt•
X1#]
X#]
Ipz
X#]
X3$]
Ipx
X3$]
]
Idh1
]
Idh0
X% ]
X1$ ]
Ipi•
X1$]
X1*] X1*
or X1* ]
Iph•
X1(] X1(
Ips•
Leading zeros are suppressed.
X1(]
IPL T S Series • Communication and Control
= hardware (MAC) address (xx-xx-xx-xx-xx-xx).
= Syntax is the same as for IP addresses.
36