Extron electronics IPL T S Series User Manual page 38

Command ASCII (Telnet)
(Host to Unit)
Bidirectional Serial Data Port (continued)
Configure parameters
24 E X! X2%
*
X2* }
CP
Example: E
4*9600,N,8,1CP
View parameters E X! }
CP
Configure mode E X! X2(
24
*
View mode E X! }
CY
Configure flow control
E X! X3)
*
View flow control E X! }
CF
Configure receive E X! X1&
*
timeout 24
View receive timeout
E X! }
CE
X!
KEY: specific port number (01
=
X1&
= Time in tens of milliseconds to wait for characters coming into a serial port before terminating (default = 1 = 10 ms, max. = 32767)
X2)
= Time in tens of milliseconds to wait between characters coming into a serial port before terminating (default = 2 = 20 ms, max. = 32767)
X2!
= Parameter to set either Length of message to receive or Delimiter value. If length delimited, use xxL, where xx is the length of the incoming message in bytes. If character delimited, use
xxD, where xx is the decimal ASCII value of the delimiting character.
X2#
= Priority status for receive timeout:
X2%
= Baud rate: 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600, 14400, 19200, 28800, 38400, 57600, or 115200
X2^
Odd Even
= Parity,
X2&
7, 8 (default = 8)
= Data bits:
X2*
1, 2 (default = 1)
= Stop bits:
X2(
0
= Port type: = RS-232
X3)
= Flow control: Hardware
X3!
= Data pacing (specified in milliseconds between bytes):
URL Encoded (Web)
Host to Unit)
X2^ X2& X! X2%
, , , W %2A %2C
X2* |
%2C CP
W4%2A9600%2CN%2C8%2C
}
|
1CP
X! |
W CP
} X! X2( |
CY W %2A CY
X! |
W CY
X3! } X! X3)
, CF W %2Al %2C
X! |
W CF
X2) X2# X2! } X! X1& X2)
* , * CE W %2A %2A
X2! |
%2A CE
X! |
W CE
99)
1 = rear host (Host Control RS-232 port)
–
2 = front panel Config port
3 = slaved switcher (MLS port)
0
= priority set to Send Data String command parameters
None (default)
Mark Space
1 2
= RS-422 = RS-485
Software None (only the first letter is needed)
0–1000
(default =
Response
(Unit to Host)
X2^ X2& X! X2% X2^
%2C Cpn •Ccp , ,
X2* ]
Cpn4•Ccp9600,N,8,1
X2% X2^ X2& X2( ]
, , ,
X! X2)]
Cpn •Cty
X2(]
X3! | X! X3) X3!]
CF Cpn •Cfl ,
X3) X3!]
,
X2# X! X1& X2)
%2A Cpn •Cce *
X1& X2) X2# X2! ]
, , ,
4 = display port (Projector RS-232/IR)
5 = IR/Serial port A
6 = IR/Serial port B
1 = priority set to Configure Receive Timeout command parameters.
(only the first letter is needed)
0
ms)
IPL T S Series • Communication and Control
Additional Description
X2& X2%
, Set baud rate ( ), parity (
X2* X!
stop bits ( ) for port
] Set the projector control port for 9600 baud,
no parity, 8 data bits, and 1 stop bit.
X2# X2! ] X1&
, ,
Set the time to wait (
X2# X!
status ( ) for port
7 = IR/Serial port C
X2^ X2&
), data bits ( ), and
.
X2)
and and priority
.
31