Agilent Technologies MSO6102A Programmer's Reference Manual page 633

TRIGger SEQuence commands, 408
trigger SPI clock slope, 417
TRIGger SPI commands, 416
trigger status bit, 136
trigger sweep mode, 332
TRIGger TV commands, 425
TRIGger USB commands, 431
trigger, CAN, 352
trigger, CAN acknowledge, 528
trigger, CAN pattern data, 345
trigger, CAN pattern data length,
trigger, CAN pattern ID, 347
trigger, CAN pattern ID mode, 348
trigger, CAN sample point, 349
trigger, CAN signal baudrate, 350
trigger, CAN signal definition, 529
trigger, CAN source, 351
trigger, duration greater than, 355
trigger, duration less than, 356
trigger, duration pattern, 357
trigger, duration qualifier, 358
trigger, duration range, 359
trigger, edge coupling, 365
trigger, edge level, 366
trigger, edge reject, 367
trigger, edge slope, 368
trigger, edge source, 369
trigger, FLEXray, 381
trigger, FLEXray error, 371
trigger, glitch greater than, 384
trigger, glitch less than, 385
trigger, glitch level, 386
trigger, glitch polarity, 387
trigger, glitch qualifier, 388
trigger, glitch range, 389
trigger, glitch source, 390
trigger, high frequency reject filter,
trigger, holdoff, 337
trigger, IIC clock source, 395
trigger, IIC data source, 396
trigger, IIC pattern address, 392
trigger, IIC pattern data, 393
trigger, IIC pattern data 2, 394
trigger, IIC qualifier, 397
trigger, IIC signal baudrate, 403
trigger, IIC type, 398
trigger, LIN, 407
trigger, LIN sample point, 402
trigger, LIN signal definition, 530
trigger, LIN source, 404
trigger, mode, 338
trigger, noise reject filter, 339
trigger, Nth edge in burst slope, 363
trigger, Nth edge of burst count,
trigger, pattern, 340
trigger, sequence, 415
trigger, sequence count, 409
trigger, sequence edge, 410
trigger, sequence find, 411
trigger, sequence pattern, 412
trigger, sequence reset, 413
trigger, sequence timer, 414
Agilent 6000 Series Oscilloscopes Programmer's Reference
trigger, SPI clock slope,
trigger, SPI clock source,
trigger, SPI clock timeout,
trigger, SPI data source,
trigger, SPI frame source,
trigger, SPI framing,
trigger, SPI pattern data,
trigger, SPI pattern width,
trigger, sweep,
trigger, threshold,
346 trigger, TV line,
trigger, TV mode, 427,
trigger, TV polarity,
trigger, TV source,
trigger, TV standard,
trigger, USB,
trigger, USB D- source,
trigger, USB D+ source,
trigger, USB speed,
truncation rules,
TST (Self Test),
tstart, 517
tstop, 518
TTL threshold voltage for digital channels, 192,
498
TTL trigger threshold voltage,
turn function on or off,
turn off channel,
turn off channel labels,
turn off cursors,
turn off delayed time base mode,
turn off digital pod,
turn off math function,
turn off measurements,
turn off trace memories,
turn on channel labels,
336 turn on channel number display,
turn on channels,
turning channel display on and off,
turning off/on function calculation,
turning vectors on or off,
TV mode, 427,
TV trigger commands,
TV trigger line number setting,
TV trigger mode,
TV trigger polarity,
TV trigger standard setting,
TV triggering,
tvmode, 532
type, 148, 460
TYPE commands,
U
361
UNITs commands,
units per division, 183, 184, 211,
units per division (vertical) for function, 183,
220
unsigned mode,
upper threshold,
upper threshold voltage for measurement,
uppercase characters in commands,
417
422
418
423
424
419
420
421
342
531
426
532
428
429
430
435
432
433
434
566
98
531
507
109
198
105
105
109
109
105
105
198
503
105
172
215
502
532
425
426
429
428
430
332
488
488
327
461
263
521
565
URQ (User Request) status bit, 81,
USB source, 432, 433
USB speed, 434
USB trigger, 435
USB trigger commands, 431
USB triggering, 332
user defined channel labels, 175
user defined threshold, 498
user event conditions occurred, 96
user-defined threshold voltage for digital
channels, 192
user-defined trigger threshold, 531
USR (User Event bit), 94, 96
utilization, CAN bus, 302
V
valid command strings, 565
valid pattern time, 355, 356
value, 274
value measured at base of waveform,
value measured at specified time,
value measured at top of waveform,
value ranges, 71
values required to fill time buckets,
vectors, 202
vectors turned on or off, 502
vectors, turning on or off, 193
vernier, channel, 185
vernier, horizontal, 328
vertical adjustment, fine (vernier),
vertical amplitude measurement,
vertical axis defined by RANGe, 218
vertical axis range for channels, 182
vertical offset for channels, 176
vertical peak-to-peak measured on
waveform, 281
vertical scale, 183, 220
vertical scaling, 453
vertical threshold, 498
vertical value at center screen, 216
vertical value maximum measured on
waveform, 279
vertical value measurements to calculate
overshoot, 261
vertical value minimum measured on
waveform, 280
video line to trigger on, 426
video standard selection, 430
view, 137, 213, 462, 503
view turns function on or off, 507
VISA COM example in Visual Basic,
VISA example in C, 595
VISA example in Visual Basic, 604
Visual Basic, VISA COM example,
Visual Basic, VISA example, 604
voltage crossing reported or not found,
voltage difference between data points,
voltage difference measured, 522
voltage level for active trigger, 366
voltage marker used to measure
waveform, 523, 524
Index
83
278
283
284
142
185
276
614
614
519
466
633