Agilent Technologies MSO6102A Programmer's Reference Manual page 631

probe sense for oscilloscope, 501,
probe skew value, 179, 499
program data, 566
program data syntax rules, 568
program example, 586, 595, 604,
program message, 77
program message syntax, 565
program message terminator, 566
programming examples, 4, 585
protecting against calibration, 164
protection, 126, 128, 181, 209
PROTection commands, 481
pulse width, 260, 266
pulse width duration trigger, 384, 385,
pulse width measurement, 248
pulse width trigger, 339
pulse width trigger level, 386
pulse width triggering, 332
pwidth, 266
Q
qualifier, 389
QUALifier commands, 481
qualifier, trigger duration, 355, 356,
query error detected in Standard Event
Status, 83
query return values, 582
query setup, 224, 233, 248, 317
query subsystem, 151, 186, 213
querying setup, 168
querying the subsystem, 332
queues, clearing, 560
quick reference, commands, 31
quoted ASCII string, 71
QYE (Query Error) status bit, 81,
R
range, 213, 330
RANGe commands, 481
range for channels, 182
range for duration trigger, 359
range for external trigger, 210
range for full-scale vertical axis, 218
range for glitch trigger, 389
range for time base, 324
range of offset values, 176
range of reference level values, 219
range qualifier, 388
ranges, value, 71
rate, 147
RCL (Recall), 88
read configuration, 85
read trace memory, 196
readout, 513
real-time acquisition mode, 139,
recall, 88, 317
recalling and saving data, 193
RECTangular window for transient signals,
reference, 213, 326
Agilent 6000 Series Oscilloscopes Programmer's Reference
506 reference clock,
REFerence commands,
reference for time base,
reference level, Fast Fourier Transform (FFT)
614 function,
reference signal (10 MHz),
reference signal mode,
registers, 82, 88, 92, 104, 113, 115, 117, 120,
122, 124, 126,
registers, clearing,
reject filter, 367
reject high frequency,
reject noise, 339
389 remote control example, 586, 595, 604,
remove cursor information,
remove labels,
remove message from display,
reorder channels,
repetitive acquisitions,
report errors,
report transition, 272,
reporting status,
reporting the setup,
request service,
Request-for-OPC flag clear,
358
reset, 89, 413
RESet commands,
reset conditions,
reset measurements, 110,
resolution of printed copy,
restore configurations, 85, 88, 92,
restore labels,
restore setup,
return values, query,
returning acquisition type,
returning number of data points,
83
right reference,
rise time measurement,
rise time of positive edge,
rising edge, 340,
RMS value measurement,
roll time base mode,
root (:) commands, 100,
root level commands,
RQL (Request Control) status bit, 81,
RQS (Request Service),
RST (Reset),
rules, tree traversal,
rules, truncation,
run, 97, 131
Run bit, 122,
running configuration, 92,
S
sample rate,
sampled data,
144
sampled data points,
SAV (Save), 92
save, 92
223
SAVE TO INTERN,
save waveforms to pixel memory,
325
481
527
219
146
325
128
560
336
614
234
198
314
105
131
315
274
541
332
96
79
481
89
195
510
317
198
88
582
148
145
326
248
267
410
282
322
102
74
83
96
89
579
566
124
317
147
502
446
119
119
saving and recalling data, 193
SBUS commands, 292
scale, 220, 327, 331
SCALe commands, 482
scale factors output on hardcopy,
scale for channels, 183
scale units for channels, 184
scale units for external trigger, 211
scaling display factors, 177
scratch measurements, 512
screen data, 196
SECAM, 426, 430
seconds per division, 327
segment, FLEXray time trigger, 379
select measurement channel, 270
self-test, 98
sensing a channel probe, 501
sensing a external trigger probe,
sensitivity of oscilloscope input, 177
sequence, 411, 412, 413
sequence trigger, 415
SEQuence trigger commands, 408
sequence triggering, 332
sequencer edge counter, 409
sequencer timer, 414
sequential commands, 583
serial clock, 395, 422
serial data, 396, 423
serial decode bus, 293
serial decode bus display, 303
serial decode mode, 310
serial frame, 424
serial number, 132
service request, 96
Service Request Enable Register (SRE), 94,
set, 89
set center frequency, 214
set conditions, 105
set cursors, 517, 518
set date, 313
set delay, 105
set thresholds, 105
set time, 319
set time/div, 105
setting digital display, 188
setting digital label, 157, 189
setting digital position, 190
setting digital threshold, 192
setting display, 215
setting external trigger level, 203
setting impedance for channels,
setting inversion for channels, 174
setting pod display, 288
setting pod size, 289
setting pod threshold, 290
settings, 88, 92
settings, instrument, 224
setup, 139, 151, 168, 186, 193, 213, 224,
setup configuration, 88, 92, 317
setup defaults, 89
setup memory, 88
setup reported, 332
Index
225
506
548
173
317
631