Agilent Technologies MSO6102A Programmer's Reference Manual page 632

Index
short form, 3, 566
show channel labels, 198
show measurements, 248, 269
SICL example in C, 586
SIGNal commands, 483
signal type, 180, 208
simple command headers, 567
single acquisition, 133
single-ended signal type, 180, 208
size, 191, 289
SIZE commands, 483
skew, 179, 499
slope, 368, 417
Nth edge in burst, 363
slope (direction) of waveform, 519
SLOPe commands, 483
slope not valid in TV trigger mode,
slope of edge, 410
slope parameter for delay measurement,
software version, 84
source, 201, 213, 270, 351, 404,
SOURce commands, 483
source for function, 221
source for trigger, 369
source for TV trigger, 429
span, 213
span of frequency on display, 222
specify measurement, 270
SPI, 417, 418, 420
SPI commands, 484
SPI decode word width, 311
SPI trigger, 419, 421
SPI trigger clock, 422
SPI trigger commands, 416
SPI trigger data, 423
SPI trigger frame, 424
SPI triggering, 332
SRE (Service Request Enable Register), 94,
SRQ (Service Request interrupt), 113,
standard deviation measured on
waveform, 268
Standard Event Status Enable Register
(ESE), 80, 553
Standard Event Status Register (ESR), 82,
standard for video, 430
standard, LIN, 405
start acquisition, 97, 111, 131, 133
start and stop edges, 253
start cursor, 517
start measurement, 248
start time, 389, 517
start time marker, 514
state memory, 92
state of instrument, 85, 317
status, 95, 134, 136
Status Byte Register (STB), 93, 95, 96,
STATus commands, 484
status data structure clear, 79
status reporting, 541
STB (Status Byte Register), 93, 95, 96,
step size for frequency span, 222
stop, 111, 135
632
stop acquisition,
stop cursor, 518
stop displaying channel,
stop displaying math function,
stop displaying pod,
stop time, 389,
storage, 92
store instrument setup, 85,
store setup, 92
store waveforms to pixel memory,
storing calibration information,
string, quoted ASCII,
subsystem commands, 74,
subtract math function, 213, 217,
sweep mode, trigger, 332,
sweep speed set to fast to measure fall
368 time, 258
sweep speed set to fast to measure rise
255 time, 267
switch disable,
456 switch, calibration protect,
sync break, LIN,
sync frame count (FlexRay),
syntax elements,
syntax rules, program data,
syntax, optional terms,
syntax, program message,
SYSTem commands,
system commands, 313, 314, 315, 316, 317,
319
system commands introduction,
T
tdelta, 513
tedge, 272
telnet ports 5024 and 5025,
548
temporary message,
120
TER (Trigger Event Register), 136,
test, self, 98
text, writing to display,
threshold, 192, 290, 498,
THReshold commands,
552
threshold voltage (lower) for
measurement,
threshold voltage (upper) for
measurement,
thresholds, 253,
thresholds used to measure period,
thresholds, how autoscale affects,
time base, 322, 323, 324, 326, 327,
time base commands introduction,
time base reset conditions,
time base window, 329, 330,
time between points,
546
time buckets, 141,
TIME commands,
time delay, 527
time delta, 513
546
time difference between data points,
time duration, 355, 356, 359,
time holdoff for trigger,
135
109
109
109
518
92
119
161
71
580
456
342
316
164
406
306
70
568
70
565
312
312
446
314
549
314
531
484
511
521
514
263
105
527
320
89
331
513
142
484
463
389
337
Agilent 6000 Series Oscilloscopes Programmer's Reference
time interval, 272, 274, 513
time interval between trigger and
occurrence, 519
time marker sets start time, 514
time per division, 324
time record, 223
time slot, FLEXray time trigger, 380
time specified, 283
time, calibration, 166
time, start marker, 517
time, stop marker, 518
time, system, 319
time/div, how autoscale affects,
time-at-max measurement, 515
time-at-min measurement, 516
TIMebase commands, 320
timebase vernier, 328
time-ordered label list, 199
timeout, 418
timer, 414
timing measurement, 248
title channels, 175
top of waveform value measured,
TOTal commands, 485
total frame count (CAN), 301
total frame count (FlexRay), 307
trace memories, how autoscale affects,
trace memory, 134, 137
trace memory data, 196
track measurements, 269
trademarks, 2
transfer instrument state, 85, 317
transmit, 196
tree traversal rules, 579
tree, command, 569
TRG (Trigger), 94, 96, 97
trigger (external) input impedance, 205,
trigger armed event register, 122,
TRIGger CAN commands, 343
trigger channel source, 390, 429
TRIGger commands, 332, 485
TRIGger commands, general, 335
trigger duration, 355, 356
TRIGger DURation commands, 354
TRIGger EBURst commands, 360
trigger edge, 410
TRIGger EDGE commands, 364
trigger edge coupling, 365
trigger edge slope, 368
trigger event bit, 136
Trigger Event Register (TER), 549
TRIGger FLEXray commands, 370
TRIGger GLITch commands, 382
trigger holdoff, 337
TRIGger IIC commands, 391
trigger level constants, 177
trigger level voltage, 366
TRIGger LIN commands, 400
trigger occurred, 96
trigger pattern, 340, 357
trigger qualifier, 358
trigger reset conditions, 89
105
284
105
505
124