St. Dynamic Delay (Stereo Dynamic Delay) - Korg KROSS Parameter Manual

Effect Guide
093: St. Dynamic Delay (Stereo
Dynamic Delay)
This stereo delay controls the level of delay according to the input
signal level. You can use this as a ducking delay that applies delay
to the sound only when you play keys at a high velocity or only
when the volume level is low.
Stereo In - Stereo Out
Left
Right
+
Envelope
Paramter
Control
Control
Target
←
Polarity
←
Threshold
←
Offset
←
Attack
←
Release
L Delay Time
L Dly[ms]
[ms]
R Delay Time
R Dly[ms]
[ms]
←
Feedback
←
Spread
High Damp
HiDamp[%]
[%]
Low Damp
LoDamp[%]
[%]
←
Wet/Dry
Src Source
Amt Amount
Control Target
This parameter selects no level control, delay output control
(effect balance), or feedback amount control.
Polarity
Threshold
Offset
Attack
Release
The "Offset" parameter specifies the value for the "Control
Target" parameter (that is set to None), expressed as the ratio
relative to the parameter value (the "Wet/Dry" value with "Control
Target" = Output Level, or the "Feedback" value with "Control
Target "= Feedback).
When "Polarity" is positive, the "Control Target" value is obtained
by multiplying the parameter value by the "Offset" value (if the
input level is below the threshold), or equals the parameter value if
the input level exceeds the threshold.
268
High Damp Low Damp
Delay
Feedback
Spread
High Damp Low Damp
Delay
FB Out
Attack, Release Control Target
Threshold
Value Explanation
None, Out, Selects from no
FB control, output, and
(Feedback) feedback p.268
Reverses level control
+, –
p.268
Sets the level where
0...100 the effect is applied
p.268
Sets the offset of level
0...100
control p.268
Sets the attack time
1...100
of level control p.268
Sets the release time
1...100
of level control p.268
Sets the delay time
0.0...274.0
for the left channel
Sets the delay time
0.0...274.0
for the right channel
Sets the feedback
–100...+100
amount
Sets the width of the
–100...+100 stereo image of the
effect sound p.266
Sets the damping
0...100 amount in the high
range p.266
Sets the damping
0...100 amount in the low
range p.266
Dry, Sets the balance
1 : 99...99 : 1, between the effect
Wet and the dry input
Selects a modulation
Off...Tempo
source for Wet/Dry
Sets the modulation
–100...+100
amount for Wet/Dry
When "Polarity" is negative, the Control Target value equals the
parameter value if the input level is below the threshold, or is
obtained by multiplying the parameter value by the "Offset" value
if the level exceeds the threshold.
The "Attack" and "Release" parameters specify attack time and
release time of delay level control.
Dry
Wet / Dry
Envelope
Wet
Target=Output Level
Wet / Dry
Polarity= (–)
Wet
Target=Output Level
Polarity= (+)
094: St. Auto PanningDly (Stereo
Auto Panning Delay)
This stereo delay effect pans the delay sound left and right using
the LFO.
Stereo In - Stereo Out
Left
Right
LFO: Tri / Sin
Paramter
L Delay
L Dyl[ms] Delay Time
[ms]
L Feedbck L Feedback
R Delay
R Dly[ms] Delay Time
[ms]
R Feedbck R Feedback
High Damp
HiDamp[%]
[%]
Low Damp
LoDamp[%]
[%]
LFO
LFO
Waveform
Shape LFO Shape
Phase Phase [deg]
Panning Freq
Pan[Hz]
[Hz]
BPM/MIDI
Pan MIDI Syc
Sync
Level
Threshold
Release
Attack
(Ducking Delay)
Delay Time
High Damp Low Damp
Pan
Delay
Feedback
Delay Pan
High Damp Low Damp
LFO Phase
LFO Shape
Value Explanation
Sets the delay time
0.0...274.0
for the left channel
Sets the feedback
–100...+100 amount for the left
channel
Sets the delay time
0.0...274.0
for the right channel
Sets the feedback
–100...+100 amount for the right
channel
Sets the damping
0...100 amount in the high
range
Sets the damping
0...100 amount in the low
range
Tri (Triangle), Selects the LFO
Sine Waveform
Changes the
–100...+100 curvature of the LFO
Waveform
Sets the LFO phase
difference between
–180...+180
the left and right
Sets the panning
0.02...20.00
speed
Switches between
using the frequency
Off, On of the panning speed
and using the tempo
and notes
Dynamic Delay
Time
Wet / Dry
Depth
Wet / Dry
p.266
p.266
p.224
p.239
p.223