Scale - Korg KROSS Parameter Manual

Sequencer mode
3–4: SCALE
Here you can adjust the settings for the scale for each MIDI track.
Scale Type (Song's Scale)
[Equal Temperament...User Octave Scale15]
Selects the scale.
Key
Random
As this value is increased, an increasingly random deviation will
be added to the pitch at each note-on.
If Status (SEQ> PROG) is INT, this setting will affect the
pitch produced by the KROSS. If Status is EXT, this setting
will affect the note number of the note messages transmitted
via MIDI.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons   to switch tracks. (see
page 105)
Use Program's Scale
MIDI tracks can use the scale that is specified by Scale (P–
BASIC> SCALE).
On (checked): The scale specified by the program will be used.
Off (unchecked): The scale specified by Scale will be used.
Track Info.
Shows the settings of tracks 1–16 for the parameter that you're
editing.
If this is disabled because of the setting of another parameter, "–"
is shown.
3–1...4: FUNCTION
V
• 0: Memory Status
• 1: Solo Setting see page 63
• 2: Undo see page 137
• 3: Create New Song
• 4: Rename Song see page 137
• 5: Delete Song see page 137
• 6: Copy From Song
• 7: Copy from Combination
• 8: Copy from Program
• 9: Load Template Song
• 10: Save Template Song (Save as User Template Song)
page 140
• 11: GM Initialize
• 12: FF/REW Speed
• 13: Detune BPM Adjust
• 14: Set Location (Set Location for Locate Key)
142
For more information, please see the "Sequencer: FUNCTION"
section on page 137.
118
see page 137
see page 137
see page 137
see page 138
see page 139
see page 139
see page 141
see page 142
see page 142
see page
4: S–ZONE /DELAY (Zones/Delay)
4–1: KEY ZONE (Keyboard Zones)
Bottom Slope
Bottom Key
Track 1
[
Track 16
C–1
[C...B]
Here you can specify the key zones where MIDI tracks 1–16 will
[0...7]
sound.
The top/bottom key settings specify the zone where MIDI tracks
1–16 will sound, and the top/bottom slope settings specify the key
range where the volume will change starting from the top/bottom
key.
For more information, please see the "4–1: KEY ZONE
(Keyboard Zones)" section on page 118.
These settings do not affect MIDI transmission/reception. All
note data that is received will be recorded into the internal
sequencer, and all note data from the internal sequencer or
from the keyboard will be transmitted.
Zone Map
[Off, On]
This area indicates the note and velocity ranges where each MIDI
track (1–16) will sound.
A line indicates the range of notes that will sound, and the slope
within that range is shaded.
Track 01...16 (Track Number)
To select a track, place the cursor at one of the following
parameters, and use the cursor buttons   to switch tracks. (see
page 105)
Top Key
Specifies the top key (upper limit) of the notes that will sound for
each MIDI track.
Top Slope
Specifies the range of keys (12 is one octave) where the volume
will be reached starting from the top key.
0: The volume will be at the original level from the top key.
12: The volume will increase gradually as you play downward,
and will reach the original volume one octave below the top key.
72: The volume will increase gradually as you play downward,
and will reach the original volume six octaves below the top key.
Bottom Slope
see
Specifies the range of keys (12 is one octave) where the volume
will be reached starting from the bottom key.
0: The volume will be at the original level from the bottom key.
12: The volume will increase gradually as you play upward, and
will reach the original volume one octave above the bottom key.
72: The volume will increase gradually as you play upward, and
will reach the original volume six octaves above the bottom key.
Bottom Key
Specifies the bottom key (lower limit) of the notes that will sound
for each MIDI track.
Top Slope
Top Key
G9
[C–1...G9]
[00, 01, 02, 03, 04, 06, 08, 10,
12, 18, 24, 30, 36, 48, 60, 72]
[00, 01, 02, 03, 04, 06, 08, 10,
12, 18, 24, 30, 36, 48, 60, 72]
[C–1...G9]