Multiband Limiter - Korg KROSS Parameter Manual

Trigger Monitor
Turning this parameter On will cause the trigger signal to be
output, instead of the effect sound. Use this parameter to check the
trigger signal with EQ applied.
Usually, this should be set to Off.
Side PEQ Insert
Side PEQ Cutoff [Hz]
Q
Gain [dB]
These parameters are used to set the EQ amount that's applied to
the trigger signal.
The Limiter determines whether the compression is applied or not,
based on the post-EQ trigger signal. Setting the equalizer allows
you to set the Limiter to respond to any frequency band.

004: Multiband Limiter

This effect applies the Limiter to the low range, mid range, and
high range of the input signal. You can control dynamics for each
range to adjust the sound pressure of the low range, mid range, and
high range in a different way from the EQ.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Band-Pass Filters
Low
Envelope - Control
Mid Low Offset
+
Envelope - Control
High Mid Offset
Envelope - Control
High Offset
Right
Paramter Value
1.0 : 1...50.0 : 1,
←
Ratio
Inf : 1
Threshold
Thrsh[dB] –40...0
[dB]
←
Attack 1...100
←
Release 1...100
Low Offset
Lo Ofs[dB] –40...0
[dB]
Mid Offset
M. Ofs[dB] –40...0
[dB]
High Offset
Hi Ofs[dB] –40...0
[dB]
Gain Adjust –Inf,
Gain [dB]
[dB] –38...+24
Src Source Off...Tempo
Amt Amount –63...+63
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
Low Offset [dB]
Mid Offset [dB]
High Offset [dB]
These parameters set the gain of the trigger signal.
For example, if you do not want to apply compression to the high
range, reduce the "High Offset" value down below the
"Threshold" level. In this way, the high range limiter will not
respond, and compression will not be applied.
Wet / Dry
Limiter
Limiter
Gain Adjust
Limiter
Wet / Dry
Explanation
Sets the signal
compression ratio
p.218
Sets the level above
which the
compressor is applied
p.218
Sets the attack time
p.218
Sets the release time
p.218
Gain of the low-range
trigger signal p.219
Gain of the mid-range
trigger signal p.219
Gain of the high-
range trigger signal
p.219
Sets the output gain
p.218
Selects the
modulation source
for the output gain
Sets the modulation
amount of the output
gain
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
Single size effects 004: Multiband Limiter
005: St.MasteringLimiter (Stereo
Mastering Limiter)
This is a stereo limiter that is optimized for mastering songs.
Stereo In - Stereo Out
Left
+
Envelope - Control
Right
Paramter Value
Threshold
Thrsh [dB] –30.0...0.0
[dB]
Out Ceiling
Ceil[dB] –30.0...0.0
[dB]
Rel [ms] Release [ms] 0.50...1000.0
Dry, 1 : 99...
←
Wet/Dry
99 : 1, Wet
Src Source Off...Tempo
Amt Amount –100...+100
006: Stereo Gate
This effect mutes the input signal when it falls below a specified
level. You can also invert the on/off status of the gate, or use note-
on/off messages to turn the gate on/off directly.
Stereo In - Stereo Out
Left
Envelope Source
Side PEQ
Envelope - Control
+
Envelope - Control
Envelope Select
D -mod
Right
FX Control BUS 1
FX Control BUS 2
Paramter Value
Dmod, Input,
Envelope
Env Src FX Control1,
Source
FX Control2
Fx Control
FXCtrl Trim 0...100
Trim
L/R Mix,
Env Sel Envelope L Only,
R Only
Src Mid Source Off...Tempo
←
Polarity +, –
←
Threshold 0...100
←
Attack 1...100
←
Release 1...100
Wet / Dry
Out Ceiling
Limiter
Limiter
Out Ceiling
Wet / Dry
Explanation
Sets the level above
which the
compressor is applied
p.218
Sets the output gain
Sets the release time
p.218
Sets the balance
between the effect
and the dry input
Selects a modulation
source for Wet/Dry
Sets the modulation
amount for Wet/Dry
Wet / Dry
Gain Adjust
Delay Gate
Trigger Monitor
Delay Gate
Gain Adjust
Wet / Dry
Explanation
Selects the source to
control the gate:
Dmod control, or use
the input signal or FX
Control Bus 1 or 2 as a
trigger p.218
Sets the trigger input
level from FX Control
Bus 1/2
Selects the control
signal: left and right
linked, left only, or
right only p.218
Selects the source
that will control the
gate when Envelope
Src = Dmod
Switches the polarity
of gating p.220
Sets the level where
gating is applied
p.220
Sets the attack time
p.220
Sets the release time
p.220
219