Xerox DocuColor 2240 Service Manual page 785

REP 9.7 Toner Dispenser ...............................................................................................
REP 9.8 Plate Assembly .................................................................................................
REP 9.9 Developer Housing ...........................................................................................
REP 9.10 Developer .......................................................................................................
REP 9.11 Toner Dispenser Base Assembly ...................................................................
REP 9.12 IBT Steering Motor Assembly .........................................................................
REP 9.13 Agitator Motor Assembly.................................................................................
REP 9.14 MOB Sensor Assembly...................................................................................
REP 9.15 IBT Belt Assembly ..........................................................................................
REP 9.16 IBT Cleaner Assembly ....................................................................................
REP 9.17 Auger Assembly..............................................................................................
REP 9.18 Lever Assembly ..............................................................................................
REP 9.19 Left Hinge/Right Hinge....................................................................................
REP 9.20 Right Lift Assembly .........................................................................................
REP 9.21 Left Lift Assembly ...........................................................................................
REP 9.22 Transfer Belt ...................................................................................................
REP 9.23 1st BTR Roll....................................................................................................
REP 9.24 2nd BTR Roll ..................................................................................................
REP 9.25 Erase Lamp/Rail (K,Y,M,C) ............................................................................
REP 9.26 ATC Sensor ....................................................................................................
REP 9.27 Retract Shaft...................................................................................................
Fuser
REP 10.1 Fuser...............................................................................................................
REP 10.2 Fuser Fan .......................................................................................................
REP 10.3 Main/Sub Heater Rod .....................................................................................
Finisher
REP 12.1 H Transport Assembly ...................................................................................
REP 12.2 H Transport Belt..............................................................................................
REP 12.3 Entrance Sensor and Top Tray Full Sensor ...................................................
REP 12.4 Finisher ...........................................................................................................
REP 12.5 Stack Height Sensor Assembly ......................................................................
REP 12.6 Eject Roll Assembly ........................................................................................
REP 12.7 Decurler Roll ...................................................................................................
REP 12.8 Finisher Drive Motor .......................................................................................
REP 12.9 Belt..................................................................................................................
REP 12.10 Rail................................................................................................................
REP 12.11 Stapler Assembly..........................................................................................
REP 12.12 Compiler Tray Assembly...............................................................................
REP 12.13 Stacker Motor Assembly ...............................................................................
REP 12.14 Front Elevator Bracket ..................................................................................
REP 12.15 Paddle Gear Shaft ........................................................................................
REP 12.16 Finisher PWB ................................................................................................
REP 12.17 Entrance Upper Cover ..................................................................................
REP 12.18 Cam Bracket Assembly ................................................................................
REP 12.19 Finisher Rack Assembly ...............................................................................
REP 12.20 Lowering Stacker Tray..................................................................................
Covers
REP 14.1 Top Cover .......................................................................................................
REP 14.2 Rear Cover (IOT) ............................................................................................
Repairs and Adjustments
4-78 REP 14.3 Right Cover .....................................................................................................
4-79 REP 14.4 Rear Left Middle Cover ...................................................................................
4-81 REP 14.5 Rear Left Upper Cover....................................................................................
4-82 REP 14.6 Left Lower Cover Assembly ............................................................................
4-83 REP 14.7 Front Cover Assembly ....................................................................................
4-84 REP 14.8 Fuser Cover ....................................................................................................
4-84 REP 14.9 Rear Cover (Tray Module) ..............................................................................
4-85 REP 14.10 Inner Cover ...................................................................................................
4-85 REP 14.11 Left Cover Assembly.....................................................................................
4-86 REP 14.12 Left Lower Cover...........................................................................................
4-86
ADJUSTMENTS
4-87
4-88
DADF
4-88
ADJ 5.1 DADF Side Registration ...................................................................................
4-89
ADJ 5.2 DADF Counterbalance ......................................................................................
4-91
ADJ 5.3 DADF Parallelism ..............................................................................................
4-97
ADJ 5.4 Document Transport Height ..............................................................................
4-97
ADJ 5.5 DADF Top Registration .....................................................................................
4-98
ADJ 5.6 DADF Document Calibration .............................................................................
4-98
ADJ 5.7 DADF Non-standard Document Custom Registration .......................................
4-100
Scanner
ADJ 6.1 Full/Half Rate Carriage ......................................................................................
4-101
4-101 Xerographic/Registration
4-102
ADJ 9.1 Max Setup .........................................................................................................
ADJ 9.2 ATC Sensor Setup (dC921)...............................................................................
ADJ 9.3 TRC Control/Toner Density Setup (dC922).....................................................
4-103
ADJ 9.4 ADC Output Check (dC934) ..............................................................................
4-104
ADJ 9.5 TRC Adjust (dC924) ..........................................................................................
4-105
ADJ 9.6 Color Registration (dC685)..............................................................................
4-106
ADJ 9.7 IIT Calibration (dC945) ......................................................................................
4-107
ADJ 9.8 Hard Disk Diagnostics/Setup (dC355)...............................................................
4-108
ADJ 9.9 IOT Registration Series (dC129) .......................................................................
4-113
ADJ 9.10 IIT Lead Edge Registration..............................................................................
4-114
ADJ 9.11 IIT Side Edge Registration...............................................................................
4-115
ADJ 9.12 IIT Vertical/Horizontal Magnification ................................................................
4-115
ADJ 9.13 UI Display Calibration ......................................................................................
4-120
ADJ 9.14 Inboard/Outboard Density ...............................................................................
4-122
ADJ 9.15 Light Image Setup ...........................................................................................
4-126
4-127 Finisher
4-131
ADJ 12.1 Finisher Alignment...........................................................................................
4-133
4-135
4-137
4-140
4-142
4-143
4-144
09/03
4-2
4-144
4-145
4-146
4-146
4-147
4-148
4-148
4-149
4-149
4-150
4-151
4-153
4-154
4-155
4-157
4-159
4-160
4-161
4-165
4-166
4-167
4-167
4-168
4-169
4-171
4-171
4-172
4-174
4-175
4-176
4-179
4-180
4-186
4-189
Initial issue
DC 3535/2240/1632, WC M24