Section 30 Jabiru Sensor Wiring Examples; Notes For Section 30 Drawings - Garmin G3X Installation Manual

30 JABIRU SENSOR WIRING EXAMPLES

30.1 Notes for Section 30 Drawings

NOTES: NOTES:
1. 1. UNLESS OTHERWISE NOTED, ALL STRANDED WIRE MUST CONFORM TO MIL-W-22759/16 OR EQUIVALENT UNLESS OTHERWISE NOTED, ALL STRANDED WIRE MUST CONFORM TO MIL-W-22759/16 OR EQUIVALENT
2. 2. UNLESS OTHERWISE NOTED, ALL SHIELDED WIRE MUST CONFORM TO MIL-C-27500 OR EQUIVALENT UNLESS OTHERWISE NOTED, ALL SHIELDED WIRE MUST CONFORM TO MIL-C-27500 OR EQUIVALENT
3. 3. UNLESS OTHERWISE NOTED, ALL WIRES ARE 24 GAUGE MINIMUM. UNLESS OTHERWISE NOTED, ALL WIRES ARE 24 GAUGE MINIMUM.
4. 4. SYMBOL DESIGNATIONS SYMBOL DESIGNATIONS
TWISTED SHIELDED SINGLE CONDUCTOR TWISTED SHIELDED SINGLE CONDUCTOR
SHIELD TERMINATED TO GROUND SHIELD TERMINATED TO GROUND
TWISTED SHIELDED SINGLE CONDUCTOR TWISTED SHIELDED SINGLE CONDUCTOR
SHIELD FLOATS SHIELD FLOATS
TWISTED SHIELDED PAIR TWISTED SHIELDED PAIR
SHIELD TERMINATED TO GROUND SHIELD TERMINATED TO GROUND
TWISTED SHIELDED PAIR TWISTED SHIELDED PAIR
SHIELD FLOATS SHIELD FLOATS
TWISTED SHIELDED 3 CONDUCTOR TWISTED SHIELDED 3 CONDUCTOR
SHIELD TERMINATED TO GROUND SHIELD TERMINATED TO GROUND
TWISTED SHIELDED 3 CONDUCTOR TWISTED SHIELDED 3 CONDUCTOR
SHIELD FLOATS SHIELD FLOATS
5. 5. UNLESS OTHERWISE NOTED, ALL SHIELD GROUNDS MUST BE MADE TO THE RESPECTIVE UNIT BACKSHELLS. UNLESS OTHERWISE NOTED, ALL SHIELD GROUNDS MUST BE MADE TO THE RESPECTIVE UNIT BACKSHELLS.
ALL OTHER GROUNDS SHOULD BE TERMINATED TO AIRCRAFT GROUND AS CLOSE TO THE RESPECTIVE UNIT AS POSSIBLE. ALL OTHER GROUNDS SHOULD BE TERMINATED TO AIRCRAFT GROUND AS CLOSE TO THE RESPECTIVE UNIT AS POSSIBLE.
6. 6. PINOUT SHOWN FOR PACKARD CONNECTOR SUPPLIED WITH KAVLICO PRESSURE TRANSDUCERS. PINOUT SHOWN FOR PACKARD CONNECTOR SUPPLIED WITH KAVLICO PRESSURE TRANSDUCERS.
FOR REFERENCE ONLY, ALWAYS CONFIRM CORRECT SENSOR CONNECTIONS USING SENSOR MANUFACTURER DOCUMENTATION FOR REFERENCE ONLY, ALWAYS CONFIRM CORRECT SENSOR CONNECTIONS USING SENSOR MANUFACTURER DOCUMENTATION
BEFOR CONNECTING WIRES. BEFOR CONNECTING WIRES.
7. 7. RESERVED. RESERVED.
8. 8. IN THIS DOCUMENT, AN ASTERISK (*) IS USED FOR SIGNALS THAT ARE ACTIVE LOW (GROUND TO ACTIVATE). IN THIS DOCUMENT, AN ASTERISK (*) IS USED FOR SIGNALS THAT ARE ACTIVE LOW (GROUND TO ACTIVATE).
INSTALLATION WIRING DIAGRAMS, THE MORE TRADITIONAL OVERLINE SYMBOLOGY IS USED. INSTALLATION WIRING DIAGRAMS, THE MORE TRADITIONAL OVERLINE SYMBOLOGY IS USED.
9. 9. OPTIONAL INSTALLATION. OPTIONAL INSTALLATION.
10. IF INSTALLING UNGROUNDED THERMOCOUPLES, THE LO SIDE MUST BE TAKEN TO A GSU SIGNAL GROUND. 10. IF INSTALLING UNGROUNDED THERMOCOUPLES, THE LO SIDE MUST BE TAKEN TO A GSU SIGNAL GROUND.
11. THE RPM SIGNAL FOR THE JABIRU 3300 IS TYPICALLY OBTAINED BY TYING INTO ONE OF THE TWO WIRES RUNNING BETWEEN THE 11. THE RPM SIGNAL FOR THE JABIRU 3300 IS TYPICALLY OBTAINED BY TYING INTO ONE OF THE TWO WIRES RUNNING BETWEEN THE
ALTERNATOR AND THE ALTERNATOR REGULATOR. ALTERNATOR AND THE ALTERNATOR REGULATOR.
TWO PALE BLUE WIRES ON THE REGULATOR SIDE CAN BE USED FOR THE SIGNAL. TWO PALE BLUE WIRES ON THE REGULATOR SIDE CAN BE USED FOR THE SIGNAL.
12. IF MEASURING BATTERY CURRENT, PLACE THE SHUNT BETWEEN THE BATTERY POSITIVE TERMINAL AND THE BATTERY CONTACTOR. 12. IF MEASURING BATTERY CURRENT, PLACE THE SHUNT BETWEEN THE BATTERY POSITIVE TERMINAL AND THE BATTERY CONTACTOR.
IF MEASURING ALTERNATOR CURRENT, PLACE THE SHUNT BETWEEN THE ALTERNATOR B LEAD AND THE POWER DISTRIBUTION BUS. IF MEASURING ALTERNATOR CURRENT, PLACE THE SHUNT BETWEEN THE ALTERNATOR B LEAD AND THE POWER DISTRIBUTION BUS.
Figure 30-1 Notes for Jabiru Sensor Drawings (for all Section 30 drawings)
190-01115-01
Rev. AA
TWISTED SHIELDED 4 CONDUCTOR TWISTED SHIELDED 4 CONDUCTOR
SHIELD TERMINATED TO GROUND SHIELD TERMINATED TO GROUND
TWISTED SHIELDED 4 CONDUCTOR TWISTED SHIELDED 4 CONDUCTOR
SHIELD FLOATS SHIELD FLOATS
S
GARMIN SHIELD BLOCK GROUND GARMIN SHIELD BLOCK GROUND
AIRCRAFT GROUND AIRCRAFT GROUND
WIRE SPLICE CONNECTION WIRE SPLICE CONNECTION
COAXIAL CABLE COAXIAL CABLE
N/C = NO CONNECTION N/C = NO CONNECTION
ONE OF THE TWO WHITE WIRES ON THE ALTERNATOR SIDE OR ONE OF THE ONE OF THE TWO WHITE WIRES ON THE ALTERNATOR SIDE OR ONE OF THE
G3X/G3X Touch Installation Manual - Jabiru Sensor Wiring Examples
WIRE COLORS ARE SHOWN WIRE COLORS ARE SHOWN
ON ON
Page 30-1