YASKAWA E7U Programming Manual page 172

The following tables detail the factory default settings for the parameters that are affected by the setting of parameter o2-04.
Drive Model Nominal
CIMR-E7U Hp
0.5/0.75
20P4
20P7 2
21P5 1.5/2
22P2 3
23P7 5
25P5 7.5
27P5 10
2011 15
2015 20
2018 25
2022 30
2030 40
2037 50
2045 60
2055 75
2075 75/100
2090 125
2110 150
Note: b8-04 = Energy Savings Coefficient
C6-02 = Carrier Frequency
E2-01 = Motor Rated Current
E2-03 = Motor No-Load Current
E2-05 = Motor Line-to-Line Resistance
L2-02 = Momentary Power Loss Ride-Thru Time
L2-03 = Momentary Power Loss Minimum Base Block Time
L2-04 = Momentary Power Loss Voltage Recovery Ramp Time
L8-02 = Overheat Pre-Alarm Level
L8-06 = Input Phase Loss Detection Level
Table B.1 208/240VAC Drives
Factory Factory Factory
Default Default Default
for for for
b8-04 C6-02 E2-01
288.2 10kHz 1.9
3.3
223.7 10kHz
6.2
169.4 10kHz
8.5
156.8 8kHz
14.0
122.9 10kHz
19.6
94.75 15kHz
26.6
72.69 15kHz
39.7
70.44 8kHz
53.0
63.13 10kHz
65.8
57.87 10kHz
77.2
51.79 10kHz
105.0
46.27 10kHz
131.0
38.16 5kHz
160.0
35.78 5kHz
190.0
31.35 8kHz
260.0
23.10 2kHz
260.0
20.65 2kHz
260.0
18.12 2kHz
Factory Default Settings B - 2
Factory Factory Factory
Default Default Default
for for for
E2-03 E2-05 L2-02
9.842 0.1
1.2
1.8 5.156 0.1
2.8 1.997 0.2
3.0 1.601 0.3
4.5 0.771 0.5
5.1 0.399 1.0
8.0 0.288 1.0
11.2 0.230 1.0
15.2 0.138 2.0
15.7 0.101 2.0
18.5 0.079 2.0
21.9 0.064 2.0
38.2 0.039 2.0
44.0 0.030 2.0
45.6 0.022 2.0
72.0 0.023 2.0
72.0 0.023 2.0
72.0 0.023 2.0
Factory Factory Factory
Default Default Default
for for for
L2-03 L2-04 L8-02
0.1 0.3 95° C
0.2 0.3 95° C
0.3 0.3 95° C
0.4 0.3 100 ° C
0.5 0.3 95° C
0.6 0.3 95° C
0.7 0.3 95° C
0.8 0.3 95° C
0.9 0.3 90° C
1.0 0.6 100 ° C
1.0 0.6 90° C
1.1 0.6 90° C
1.1 0.6 95° C
1.2 0.6 100 ° C
1.2 0.1 105° C
1.3 0.1 110° C
1.5 0.1 100° C
1.7 0.1 95° C
Factory
Default
for
L8-06
5
7.5
10
12
12
10
17
21
17
15
24
20
18
20
17
16
18
20