Konica Minolta DRYPRO Model 793 Operation Manual page 127

Ch.6 Troubleshooting
Error Code Error Message
E4426 ERR_MEC1_OPEFAIL
Press the release button and check film path.
E4427 ERR_MEC1_OPEFAIL
Press the release button and check film path.
E4510 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4511 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4610 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4620 ERR_MEC1_OPEFAIL
Press the release button and check film path.
E4621 ERR_MEC1_OPEFAIL
Press the release button and check film path.
E4723 ID_ERR_MEC1_NOTFILTER
Filter after a re-set Press the release button.
E4810 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4811 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4812 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4813 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4814 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4815 ID_ERR_MEC1_FILMJAM
Press the release button and remove the film.
E4840 ID_ERR_MEC1_SORTERFAIL
Confirm the setting and press the release button.
E4A20 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
E4A21 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
E4A22 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
E4A23 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
E4A24 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
E4A25 ID_ERR_MEC1_COVEROPEN
Close the cover and press the release button.
An error code "CXXXX" may be displayed depending on a connected device. This
indicates an error relating to the DICOM communication, and has no influence upon
the DRYPRO 793. Thus print operation can be continued without problem.
Where errors "EXXXX" or "FXXXX" not shown in the list above occur, carry out error
reset following the procedure detailed in the section "Error Reset." If the error
repeats after resetting, switch off the DRYPRO 93 power supply by pressing the
operation switch and contact the nearest representative. In such cases, do not
switch off the power supply breaker.
If, however, the DRYPRO 793 emits unusual noises or smoke, the power supply
breaker should be switched off immediately, the power supply cord disconnected
and your technical representative contacted.
DRYPRO Vstage MODEL 793 Operation Manual Ver.1.01 2005.1
Error Descriptions
Position Retainer not descend.
Position Retainer not ascend.
Film jam in the Descent Transport Unit.
Film jam in the Elevator Transport Unit.
Film jam in the Elevator Transport Unit.
In release process of the elevator nip process,
Elevator Nip Sensor was not deactivated.
In process of the elevator nip process,
Elevator Nip Sensor was not activated.
Deodorant Filter not present.
Film jam in the Cooling Unit.
Film jam in the Cooling Unit.
Film jam in the Film Ejection Unit.
Film jam in the Sorter Transport Unit.
Film jam in the Film Ejection Unit.
Film jam in the Sorter Transport Unit.
Sorter selected despite it is not attached.
Front Lower Cover is open.
Left Cover is open.
Right Cover is open.
Front Upper Cover is open.
Exit Cover is open.
Sorter Cover is open.
< 125 >
Reset
Refer to "Film Jam in the Descent Transport Unit".
Note : Film jam is suspected as the cause.
Refer to "Film Jam in the Descent Transport Unit".
Note : Film jam is suspected as the cause.
Refer to "Film Jam in the Descent Transport Unit".
Refer to "Film Jam in the ElevatorTransport Unit".
Refer to "Film Jam in the ElevatorTransport Unit".
Refer to "Film Jam in the ElevatorTransport Unit".
Note : Film jam is suspected as the cause.
Refer to "Film Jam in the ElevatorTransport Unit".
Note : Film jam is suspected as the cause.
Check the Deodorant Filter is present, and
perform Error Reset
Refer to "Film Jam in the Cooling Unit".
Refer to "Film Jam in the Cooling Unit".
Refer to "Film Jam in the Film Ejection Unit".
Refer to "Film Jam in the Sorter Transport Unit".
Refer to "Film Jam in the Sorter Transport Unit".
Refer to "Film Jam in the Sorter Transport Unit".
Unselect the Sorter (Sorter not used), and
perform Error Reset.
Close the Front Lower Cover, and perform Error
Reset.
Close the Left Cover, and perform Error Reset.
Close the Right Cover, and perform Error Reset.
Close the Front Upper Cover, and perform Error
Reset.
Close the Exit Cover, and perform Error Reset.
Close the Sorter Cover, and perform Error Reset.
p.00 Resolving the
Film Jam
p.00 Caution Label
p.00 Error Reset