siemens CU250D-2 PN-F PP Manuals

Manuals and User Guides for siemens CU250D-2 PN-F PP. We have 1 siemens CU250D-2 PN-F PP manual available for free PDF download: Original Instructions Manual

siemens CU250D-2 PN-F PP Original Instructions Manual

siemens CU250D-2 PN-F PP Original Instructions Manual (382 pages)

CU250D-2 Series

Brand: siemens | Category: Inverter | Size: 15.2 MB

Table of Contents

Changes in this Manual
5
Table of Contents
7
1 Fundamental Safety Instructions

13
2 Introduction

21
- About this Manual
  21
- Guide through this Manual
  22
3 Description

23
- SINAMICS G120D CU250D-2 Inverter
  23
- Commissioning Tools
  25
- Supported Motor Series
  27
4 Installation

29
5 Commissioning

55
6 Adapt Inputs and Outputs

79
- Digital Inputs
  80
- Fail-Safe Digital Input
  81
- Digital Outputs
  83
7 Configuring the Fieldbus

85
8 Setting Functions

111
- Overview of the Converter Functions
  111
- Inverter Control
  113
- Switching the Motor on and off
  113
- Running the Motor in Jog Mode (JOG Function)
  115
- Switching over the Inverter Control (Command Data Set)
  117
- Setpoints
  119
- Overview
  119
- Specifying the Setpoint Via the Fieldbus
  120
- Motorized Potentiometer as Setpoint Source
  120
- Fixed Speed as Setpoint Source
  123
- Setpoint Calculation
  126
- Overview of Setpoint Preparation
  126
- Invert Setpoint
  127
- Inhibit Direction of Rotation
  128
- Skip Frequency Bands and Minimum Speed
  129
- Speed Limitation
  130
- Ramp-Function Generator
  131
- Motor Control
  136
- V/F Control
  136
- Characteristics of U/F Control
  137
- Selecting the U/F Characteristic
  138
- Optimizing with a High Break Loose Torque and Brief Overload
  138
- Vector Control
  140
- Checking the Encoder Signal
  141
- Select Motor Control
  141
- Optimizing the Speed Controller
  142
- Advanced Settings
  144
- Operating the Converter Without Position Controller
  145
- Basic Positioner and Position Control
  147
- Commissioning Sequence
  148
- Normalizing the Encoder Signal
  149
- Define the Resolution
  149
- Modulo Range Setting
  151
- Checking the Actual Position Value
  153
- Setting the Backlash
  154
- Limiting the Positioning Range
  156
- Setting the Position Controller
  158
- Precontrol and Gain
  158
- Optimizing the Position Controller
  159
- Limiting the Traversing Profile
  162
- Setting the Monitoring Functions
  164
- Standstill and Positioning Monitoring
  164
- Following Error Monitoring
  166
- Cam Sequencer
  168
- Referencing
  169
- Referencing Methods
  169
- Setting the Reference Point Approach
  170
- Setting the Flying Referencing
  176
- Set Reference Point
  181
- Absolute Encoder Adjustment
  183
- Jogging
  185
- Jog Velocity
  185
- Incremental Jogging
  186
- Setting Jogging
  186
- Traversing Blocks
  188
- Travel to Fixed Stop
  196
- Examples
  201
- Direct Setpoint Input (MDI)
  203
- Protection and Monitoring Functions
  209
- Inverter Temperature Monitoring
  209
- Motor Temperature Monitoring Using a Temperature Sensor
  212
- Protecting the Motor by Calculating the Motor Temperature
  215
- Overcurrent Protection
  217
- Application-Specific Functions
  218
- Functions that Match the Application
  218
- Unit Changeover
  219
- Changing over the Motor Standard
  220
- Changing over the Unit System
  221
- Switching Units with STARTER
  222
- Electrically Braking the Motor
  224
- DC Braking
  224
- Braking with Regenerative Feedback to the Line
  227
- Motor Holding Brake
  228
- Monitoring the Load Torque (System Protection)
  232
- Load Failure Monitoring
  234
- Speed Deviation Monitoring
  235
- Safe Torque off (STO) Safety Function
  237
- Function Description
  237
- Prerequisite for STO Use
  239
- Commissioning STO
  239
- Commissioning Tools
  239
- Protection of the Settings from Unauthorized Changes
  240
- Resetting the Safety Function Parameters to the Factory Setting
  240
- Changing Settings
  241
- Interconnecting the "STO Active" Signal
  242
- Setting the Filter for Safety-Related Inputs
  243
- Setting the Forced Checking Procedure (Test Stop)
  246
- Activate Settings
  247
- Checking the Assignment of the Digital Inputs
  248
- Acceptance - Completion of Commissioning
  250
- Switchover between Different Settings
  254
9 Backing up Data and Series Commissioning

257
10 Corrective Maintenance

275
11 Alarms, Faults and System Messages

299
- Alarms
  299
- Faults
  303
- Status LED Overview
  308
- Identification & Maintenance Data (I&M)
  310
- System Runtime
  311
- List of Alarms and Faults
  312
12 Technical Data

325
Appendix

337
- New and Extended Functions
  337
- A.1 New and Extended Functions
  337
- Star-Delta Motor Connection and Application Examples
  340
- Parameter
  341
- A.3 Parameter
  341
- Handling STARTER
  344
- Change Settings
  344
- A.4 Handling STARTER
  344
- Optimize the Drive Using the Trace Function
  346
- Interconnecting Signals in the Inverter
  349
- Fundamentals
  349
- Example
  351
- A.5.2 Example
  351
- Application Examples
  353
- Setting an Absolute Encoder
  353
- A.6 Application Examples
  353
- Go Online with STARTER Via PROFINET
  357
- Adapting the PROFINET Interface
  357
- Create a Reference for STARTERS
  358
- Call the STARTER and Go Online
  359
- Connecting the Safety-Related Input
  359
- Connecting Fail-Safe Digital Inputs
  360
- Setting a Non Standard HTL Encoder
  361
- Setting a Non Standard SSI Encoder
  362
- Acceptance Tests for the Safety Functions
  365
- Recommended Acceptance Test
  365
- Machine Documentation
  368
- A.9.2 Machine Documentation
  368
- Log the Settings for the Basic Functions, Firmware V4.4
  370
- Manuals and Technical Support
  371
- Manuals for Your Inverter
  371
- Configuring Support
  372
- Product Support
  372
- A.10.2 Configuring Support
  372
- Mistakes and Improvements
  373
- Index
  375

Advertisement

Advertisement

Related Products

siemens Categories

Industrial Equipment Controller Control Unit

Oven

Washer

More siemens Manuals